-
Product
PCB Adapter, Receiver, SIM, VTAC, 16 Positions, 6 Slots, to (1) Cat6
510170105
PCB Adapter (Receiver)
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules. Please note this part is too wide for use in multiple adjacent slots (for more information, please reference the attached drawing).
-
Product
Receiver, G20, 20 Module, 6.75" Series Adapters, EMI
310120193
Receiver
Receiver, G20, 20 Module, 6.75" Series Adapters, EMI
-
Product
32/64-Bit 33/66 MHz PCI-X-to-PMC-X Adapter
4068
-
The Technobox, Inc. P/N 4068 PCI-X-to-PMC-X Adapter permits operation of a standard 32- or 64-bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
Product
Shuttle Bus PMC Intelligent Interface Card
IIB-SB-PMC
-
The Shuttle Bus PMC is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, Multiplex De-Multiplex Multiple Remote Terminal, and Ground Data Bus (GDB)capability to the Shuttle Bus, together with a Pulse Code Modulation Mode. This card provides all features and functions required in a PMC platform, withSimplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
Test Adapter
RAMCHECK® SIMM
-
The RAMCHECK SIMM Adapter is another addition to the RAMCHECK memory tester. It provides a needed solution for testing older 72-pin EDO/FPM DRAM SIMM modules. An optional adapter for 30 and 72-pin SIMMs is also available
-
Product
PMC to PCI Adapter for test and development
8091
-
The PMC-to-PCI Adapter for Test is an active extender that accommodates live insertion of one PCI Mezzanine Card (PMC) for performance analysis and testing in a PCI bus environment.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
LXI Reed Relay Matrix - Single 32x32 Plugin, No Direct Y Access, 1 Analog Bus
65-227-101
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
PCIe Adapter for 3 IP Modules
PCIe3IP
-
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (f), 26.5 to 40 GHz
R281A
-
The Keysight R281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Adaptive Inverse for Actuator Compensation Toolbox
AIFAC
-
Actuator nonlinearities such as dead-zone, backlash, and hysteresis are ubiquitous in mechanical connections, hydraulic servo-valves, electric servomotors, piezoelectric, pneumatic and magnetic actuators, and even appear in biomedical systems. The Adaptive Inverse For Actuator Compensation (AIFAC) Toolbox for Simulnk allows control system engineers to design high-performance adaptive controllers to compensate for uncertain or undesirable actuator dynamics that would otherwise adversely affect closed-loop control system performance.
-
Product
Adapter, 2.4 mm (m) to APC-7, DC to 18 GHz
11902A
-
The Keysight 11902A is a 2.4 mm male to APC-7, metrology grade adapter with dc to 18 GHz operation.
-
Product
PCIe Smart Bus Extenders
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system enabling rapid production testing and engineering debug. The hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
Dsub25 To 5 SMB Adapter
PX0106A
-
Keysight's PX0106A Adapter converts Dsub25 outputs to five SMB outputs with path through connection. It supports the Keysight M9614/15A.
-
Product
High-Stability Adapter
10723A
-
The Keysight 10723A high-stability adapter converts the 10706A Plane Mirror Interferometer into an 10706B High-Stability Plane Mirror Interferometer. The 10706B is a thermally-stable optic with measurement drift reduced to approximately 1/12 the value achieved by conventional plane mirror interferometers.
-
Product
Mid Bus Probes
MBP850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
EMI Filters & Adapters
Emissions
-
The commonality in this section is conducted noise. Noise is not just a consideration when complying with EMC legal requirements, its is also potentially damaging and/or cause of failure of product performance or communications, even if the noise level is below EMC standards limits.
-
Product
Radar Power Bus Simulation
-
AMETEK Programmable Power, Inc.
Provides sequenced programmable power to a phased array radar test facility
-
Product
3-slot ATX-supported PICMG Bus Passive Backplane (vertical)
ATX6022/3VP2
-
*1 PICMG, 2 PCI*Compatible with AX61120TP*Supports ATX power supply*For 1U chassis
-
Product
Test Port Adapter Set, 2.4 Mm To 3.5 Mm
85130F
-
The Keysight 85130F test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector designed for connecting to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.
-
Product
Single Front Slot Universal Low-Profile PCI to PCMCIA Adapter, Black Bezel
P313B
-
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P313. This model, from the P-series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
-
Product
Local DVB-T2 Adapter
T2 Edge DTH
-
T2Edge DTH is ENENSYS local DVB-T2 adapter of the OneBeam DVB-T2 solution. Running on the transmission site prior to the DVB-T2 transmitter, the T2Edge DTH aims at receiving a DTH stream to build a new DVB-T2 multiplex. It selects the services from the DTH stream and generates a T2-MI stream. The T2EdgeDTH performs an advanced PSI/SI processing to update PSI/SI information related to the filtered services.
-
Product
Adapter, 2.4 mm (f) to 3.5 mm (m), DC to 26.5 GHz
11901D
-
The Keysight 11901D is a metrology grade, 2.4 mm female to 3.5 mm male adapter with dc to 26.5 GHz operation.
-
Product
PXI 4 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-021-184X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PMC to PCI Express Adapter w/ TSI384
8636
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI Express primary side and a PCI/PCI-X secondary side.
-
Product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 2 Slots, Texas Instruments PCI1520 Chipset
P222-TI1520
-
The PCI to 2-slot PCMCIA/CardBus PC-Card adapter supports 3.3V & 5V PC-cards (PCMCIA/Cardbus) simultaneously. Hot-swap PCMCIA/Cardbus PC-cards without powering off the system. 2 independent icons in MY COMPUTER. The adapter is quick & easy to install, allowing PC-card devices to be used in any desktop or tower PC.
-
Product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
-
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
