-
-
Product
PMC to PCI Adapter / Carrier
PMC2PCI
-
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.
-
Product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
-
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
AC Current Clamp Adapter
LAD-800
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable CT ratio 10:1 and 100:1.●φ80mm CT window, possible to measure from leakage to big current up to 1000A.
-
Product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
Local DVB-T2 Adapter
T2 Edge DTH
-
T2Edge DTH is ENENSYS local DVB-T2 adapter of the OneBeam DVB-T2 solution. Running on the transmission site prior to the DVB-T2 transmitter, the T2Edge DTH aims at receiving a DTH stream to build a new DVB-T2 multiplex. It selects the services from the DTH stream and generates a T2-MI stream. The T2EdgeDTH performs an advanced PSI/SI processing to update PSI/SI information related to the filtered services.
-
Product
Cables & Adapters
-
Are available in various lengths and are equipped with a variety of video, audio, and control connectors.
-
Product
PCIe Adapter for 3 IP Modules
PCIe3IP
-
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
Product
Adapter / Carrier Converter Card
PCIBPC104pET
-
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
Product
14-slot PICMG 1.3 Bus Passive Backplane
FAB101
-
The FAB101 features one CPU card slot and thirteen 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Furthermore, the FAB101 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491, and AX6145, to house the FAB101 and any customer's industrial integrations flexibly.
-
Product
Banana Adapters
-
Pasternack Enterprises Banana adapters category has 6 part numbers, the majority are RoHS and REACH compliant. impedance Banana adapters are part of a complete adapter product line from Pasternack.
-
-
Product
Robust Din-rail Fanless Embedded System With RISC-based (i.MX 6) Processor 4 COM, 2 CAN Bus And DIO
rBOX630
-
*Fanless design*RISC-based module (i.MX 6) processor*1 GB DDR3 SDRAM onboard*4 GB eMMC onboard*Completed industrial AP development software*Wide range DC power input (12 - 48V) with terminal block*Ready-to-run embedded Linux operating system*Wide temperature operation of -40°C ~ +70°C
-
Product
XMC-to-PCI Express Adapter
4821
-
The XMC2PCE is a passive 8X XMC to PCI express carrier card which permits the use of XMC cards in PC style PCI express 1X, 2X, 4X, 8X or 16X motherboard slots.
-
Product
16-Port RS232 Async Serial Communications Adapter PMC
2238
-
The Technobox 16-Port Async Communication adapter provides sixteen 16550-based UARTs using RS232 signaling levels.
-
Product
Adapters & Pin Converters
-
Need to adapt your emulator's JTAG connection? We have a variety of pin converters to help connect your debug probe to your target board's JTAG connection, such as TI, MIPI, ARM, and Cortex.
-
Product
NI-5752B, 50 MS/s, 12-Bit, 32-Channel, Kintex-7 FPGA Support, Digitizer Adapter Module for FlexRIO
784062-01
Digitizer
The NI‑5752B is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions. The NI‑5752B is compatible only with PXI FPGA Modules for FlexRIO that have Kintex‑7 FPGAs.
-
Product
Test Adapter
FECVF1600
-
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
XMC-to-PCI Express Adapter
7769
-
Our XMC-to-PCI Express Adapter 1X w/ VITA 61 (XMC 2.0) Style Connectors (7769) permits the use of a single-wide XMC module in a 1X PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector.
-
Product
PCIe Gen3 X16 Bus Expansion Via Dual X8 OCuLink
PCI125
-
The PCI125 is VadaTech’s 4th generation PCIe expansion module based on the PCI-SIG specification. The Module has a Retimer/Conditioner to improve signal integrity for enhancing system performance and reliability across long cables. It removes both random and deterministic jitter from the input signals eliminating inter-symbol interference and resets the output jitter budget. It supports the full 16 lanes.
-
Product
STD Bus, Vectorbord Plugbord
4610-1
-
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
Product
Adapter
P350NM75NF
-
P350NM75NF Adapter, Frequency Range: Up to 12 GHz, Impedance: 50 Ohm to 75 Ohm
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Square Post for Wire Wrap
610138118
Signal Contact (Receiver)
Primary mating contact 610138200. (May mate with other Twin Female contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
BGA Socket And BGA Adapter Systems
-
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
-
Product
Bus Analyzers & Exercisers
Analyzer
Corelis offers several bus analyzer products to satisfy different technical needs and price points. Corelis bus analyzers and exercisers offer analysis, test, debug, and validation capabilities for product development, system integration, and manufacturing of digital boards and systems. All of our bus analyzers are PC-based and come with software that runs on Microsoft Windows 7, Windows 8/8.1 and Windows 10.
-
Product
Receiver, G20, 20 Module, 6.75" Series Adapters, EMI
310120193
Receiver
Receiver, G20, 20 Module, 6.75" Series Adapters, EMI
-
Product
Digitizer Adapter Module For FlexRIO
Digitizer
Digitizer Adapter Modules for FlexRIO can be used with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO to create a high‐performance instrument with customizable firmware. With sampling rates from 40 MS/s to 3 GS/s and up to 32 channels, these modules cover a wide range of requirements for both time- and frequency‐domain applications. Digitizer adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
