-
Product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 6 Bus Matrix Inputs
40-569B-116
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-116 is a 8 slot module fitted with 6 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
Tap Adapter
-
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB208
-
The FAB208 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB208 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110. We have two enclosures, the AX60551 and AX60552, to house the backplane.
-
Product
VME Bus Analyzer / Exerciser
VME650
-
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
Product
6-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB210
-
*Designed for PICMG 1.3 SBC*Compatible with AX61222TP/AX61220TP chassis*Supports one PICMG 1.3 CPU card slot, two PCI slots, two PCIe x1 slots, and one PCIe x16 slot
-
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-194A-001
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
MiniPCI Express to M.2 PCIe Adapter (B-key)
SKU-089-12
-
MiniPCI Express Adapter has M.2 (B-key) connector. It allows connection M.2 modules with B-key to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits, and this Adapter supports PCI express, SIM and USB 2.0 interfaces.
-
-
Product
Adapter Kit, 3.5 mm to Type-N, DC to 18 GHz
11878A
-
The Keysight 11878A adapter kit provides the RF components generally required when an SMA or 3.5 mm device needs to be measured with a network analyzer type-N configuration. This kit includes four type-N to 3.5 mm adapters for both male and female connectors.
-
Product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
-
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Robust Din-rail Fanless Embedded System With RISC-based (i.MX 6) Processor 4 COM, 2 CAN Bus And DIO
rBOX630
-
*Fanless design*RISC-based module (i.MX 6) processor*1 GB DDR3 SDRAM onboard*4 GB eMMC onboard*Completed industrial AP development software*Wide range DC power input (12 - 48V) with terminal block*Ready-to-run embedded Linux operating system*Wide temperature operation of -40°C ~ +70°C
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
ABex Rear Module for Direct Analog Bus Connection
ABex RM-RUBI
-
The ABex RM-RUBI is a rear module for the ABex system. It’s designed to connect instruments to the analog bus backplane from the back side of a chassis and to route signals for debugging purpose. Each of the 30 analog buses can be routed to one of the four 4 SMB-connectors.
-
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
PCIe-PXIe-8565
PXI Express Module
Includes PCIe-8560 peripheral card, PXIe-8565 3U system module, and ACL-EXPRESS cable in 1, 3, or 7 meter lengthsCompliant with PXI-5 PXI Express hardware specification Rev.1.0 and PCI Express Base Specifications Rev. 1.0a250 MB/s maximum system throughput
-
Product
Flexible 32-bit PCI to x1 PCI Express Adapter
SKU-049-0X
-
The Flexible 32-bit PCI to x1 PCI Express Adapter (Adapter) was designed to expand the 32-bit PCI bus into an x1 PCI Express bus. It allows you to connect the x1 PCI Express expansion board to the motherboard PCI connectorThe Adapter includes an x1 PCI Express adapter board, 32-bit PCI host board and PCI Express Flat cable.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
CEI-2x10GBASE-T
Network Interface Controller
- Support up to two 10GbE BASE-T interfaces- Marvell AQR113C inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
PCIe Adapter for 3 IP Modules
PCIe3IP
-
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
Adapter Hermetic
-
Hermetic(1*10-6atm cc/sec), Hermetic(1*10-8atm cc/sec) & vacuum (1*10-6 Torr), Hermetic(1*10-8atm cc/sec), Hermetic(1*10-8atm cc/sec) & vacuum (1*10-7 Torr)
-
Product
MiniPCI Express to M.2 PCIe(1) Adapter (E-key)
SKU-089-10
-
MiniPCI Express has M.2 (E-key) connector. It allows connection M.2 modules with M.2 (E key) or (A-E key) to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits and this Adapter supports PCI express (slot 1) and USB 2.0 interfaces.
-
Product
Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 110 GHz
11920B
-
The Keysight 11920B precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms and frequency range from dc to 110 GHz.
-
Product
Avionics Communications Bus
ARINC-664 p7 (AFDX)
-
ARINC-664 p7 (AFDX) is an avionics communications bus that has been mandated by both Boeing and Airbus for use in new civilian avionics designs. The following tutorial provides a brief introduction to the central features of AFDX.
-
Product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
RF Adapter Module
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
Product
PCIe Basic Protocol Tx and Bus Monitor
Sy629PCIe-BPM
-
The Sy629PCIe-BPM card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory.
-
Product
NM-SF 50 N-Male to SMA-Female Adapter
-
NM-SF 50 Adapter, N-Male to SMA-Female, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
Product
14-Slot 32-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6014R
Backplane
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- PICMG 2.7 Dual system Bus specificationR1.0 compliant- One system slot with 13 expansion slots, system on the middle slot of the backplane
-
Product
RF & Microwave Connectors, Adapters And Cables
-
SHF Communication Technologies AG
RF adapters, microwave cable assemblies and high frequency connectors up to 110 GHz can be supplied by SHF. Our partners KMCO and Totoku are located in Japan and provide excellent product quality, competitive pricing and fast delivery.
