Circuit
-
product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
4 & 5 Pin Trailer Circuit Tester
PT7866
Traces each lighting function to the terminal in question. Plugs into the trailer plug. Each LED light corresponds to the circuit being energized. Provides an easy to connect ground terminal for trailer lighting set-up.
-
product
Multifunction Tester
COMBI521
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
M2T Transmitter
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
-
product
Riser
Designed to provide extra space in a SUMIT stack. They are printed circuit boards (PCBs) with SUMIT mounting holes and bus connectors.
-
product
Phase Locked Oscillators
Phase locked oscillators (PLO) utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals at lower frequencies. Frequency multipliers, amplifiers and filters are used to extend the low frequencies for higher frequency requirements. The standard offering covers the frequency range of 2 to 110 GHz and provides both internal and external reference options. The frequency stability and phase noise are dependent on the oscillator reference type.
-
product
Torque Meter Bench
BTR is a desktop torque for torque meas urements consisting of a digital indicator model DTR and a strain gauge torque extremely rugged and compact which has a precision better than 0.20%. Ideal for the calibration and the control of torque keys and to rque screwdrivers. Microprocessor indicator is fed by 4 internal batteries with an autonomy of 200 hours, with the AUTO POWER OFF function which activates if any change in the measurement is detected in an interv al of 30 minutes. The new generation electronic section consists of a particularly long-term stable analogue circuit and of a 16 bits A/D converter which ensures 65.000 internal divisions with an acquisition sp eed of 200 conversions per second. On the display there is an analogue bar for torque, that is still active, even in the programming menu.
-
product
LIGHT RANGER MUTT
TT9103
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
product
1000 Amp AC/DC Inductive Amp Clamp
6043
• A great tool for accurate measurement of current sources up to 1000 amps• Use with most digital multi-meters• 1mV/Amp output guarantees easy reading on your meter• Ideal for checking starter draw, alternator output or parasitic battery drain testing• Design allows accurate current readings without breaking the circuit• Low battery indication – auto power-off• Switch settings OFF/200A/1000A• Large jaw opening, 2.2″ and large jaw space, 2.2″ x 2.75″• Imported
-
product
ESD Testers
Hanwa Electronic Ind. Co.,Ltd.
◆Adaptable to the following international standard waveform;JEDEC, ESDA, AEC, and JEITA◆This system’s uniquely short discharge circuit is made possible by its original mechanical design.◆The short circuit minimizes the influence of inductance and capacitance on the data.◆The use of a single circuit ensures data stability for each device pin tested.
-
product
Power Supply 302D
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
product
Fast Photo-Electric Tester
LS616S
The machine is made up of three main parts: measuring circuit of electric parameter, measuring circuit of photometric parameter and circuit of CPU system. Voltage and current signals are amplify and sent to high speed A/D transform, and the transform digital signals are sent to microprocessor, the input current signals of brightness detector are sent to A/D transform via I/V convert, and the transform digital signals are sent to microprocessor. Microprocessor processing the input photometric and electric data, it automatic switch between different range and calculate and display the data in the mean time.
-
product
Torque Transducers
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
product
Surface Insulation Resistance Testing
AutoSIR2™
One AutoSIR chassis can hold between 1 to 16 measurement cards and can monitor up to 256 x 2-point test patterns or 78 x 5-point test patterns, or 32 x 9-point test patterns at selectable intervals from minutes to days. Each channel is current limited (1 M Ω), ensuring that dendrites are preserved for failure analysis. The frequent monitoring capability provides a full picture of the electrochemical reactions taking place on a circuit assembly, and provides early trend analysis enabling tests to be curtailed, thus saving considerable test time and money.
-
product
Cable Testers
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
product
Analogue (1kV below) Insulation Tester
4132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
product
Loop / PFC Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Configurable CAN FD Module With A Focus On Analog I/Os
PCAN MicroMod FD Analog 1
The PCAN-MicroMod FD breadboard can be purchased together with ready-to-use motherboards that provide peripherals for specific requirements. Spring clamp connectors are used to connect CAN, I/O and supply. The motherboard PCAN-MicroMod FD Analog 1 focuses on analog inputs and outputs, which are provided with the appropriate protective circuit.
-
product
Potential Transformers
Osborne Potential Transformers (PT’s) are used to reduce higher system voltages to lower values that are appropriate for instrumentation and/or protection circuits. They have been designed to meet specified current ratios, and burden impedance at a specified transformation error. One area of unique Osborne expertise is in designing for phase shift when potential transformers are to be used for power measuring applications.
-
product
Reliability Testing
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
product
Clamshell Type Mechanical Fixtures
Series 10
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
product
Rogowski AC Current Probe,30 MHz, 600 A
N7041A
The Keysight N7041A Rogowski coil current probe measures AC currents up to 600 A, with bandwidth ranging from 12 Hz to 30 MHz. The probe has a thin, lightweight, flexible, and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult-to-reach parts and confined spaces of a circuit under test. It can also measure large AC current without an increase in transducer size.
-
product
RF Amplifier
SA831
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition, because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
product
SparkFun Qwiic MicroPressure Sensor
The SparkFun Qwiic MicroPressure Sensor is a miniature breakout equipped with Honeywell's 25psi piezoresistive silicon pressure sensor. This MicroPressure Sensor offers a calibrated and compensated pressure sensing range of 60mbar to 2.5bar, easy to read 24 bit digital I2C output, and can be calibrated and compensated over a specific temperature range for sensor offset, sensitivity, temperature effects, and non-linearity using an on-board Application Specific Integrated Circuit (ASIC). With its ultra-low power consumption and Qwiic ports, you've got yourself a power packed little sensor!
-
product
Cable Assemblies for Interconnect Solutions
High quality connectors are just the beginning. Circuit Assembly (CA) also has over three decades of experience in producing a wide variety of cable assemblies for various applications. CA has the technical and manufacturing capabilities to provide customers with high-quality and cost-effective cable assemblies tailored to meet their needs. Circuit Assembly utilizes a quality process recognized by ISO 9001, and CA's cable assemblies are UL/CSA certified.
-
product
Vacuum Meters
* Absolute vacuum & absolutepressure measurement.* Wide measure range from 1 to1500 mbar.* Overload protection up to 2000mbar max.* 8 kind display units :torr, mm Hg, micron, mbar, KPa,Pa, inch Hg, psi* Separate probe, easy operation.* Heavy duty sensor used for air, oilgas, liquid.* Auto shut off saves battery life.* Microprocessor circuit.* Maximum & minimum records.* Data Hold function.
-
product
PWM Type AC Power Supply
LSP-5KVA
• Circuit Type: (IGBT) MPWM Pulse Duration Modulation • Input: 1 Phase 220V±10%, 50Hz/60Hz±5% • Output Voltage: HIGH/LOW Adjustable 1)1 Phase Voltage Range: (HIGH)0～300V, (LOW)0～150V 2) Nominal Voltage: +10%～+25%, -10%～-30% • Output Frequency: 50Hz, 60Hz, adjustable between 45 and 70 Hz, 400Hz • Load Voltage Stabilization Rate: ≦0.5% • Frequency Stabilization Rate: 0. 1% (Fix Point 50Hz, 60Hz and 400Hz) • Wave Distortion Rate: ≦2% (Resistor Load); Efficiency: ≧85% • Output Instruments: Frequency Indicator, 4-digits RMS digital frequency indicator, resolution is 0.1Hz Voltage Meter, 4-digits RMS digital voltage meter, resolution 0.1V Ampere Meter, 4-digist RMS digital ampere meter, resolution 1Ma Power Indicator, 4-digits RMS digital power indicator, resolution 1W Power Factor Meter Resolution 0.001 • Protective Devices: Over load, short circuit, over voltage, over current, over temperature protective and alarm devices • Operating Environment: Temperature 0～40℃ Relative Humidity 0～90%
-
product
Winding Resistance Meter 50Amps, 2 Channels
WR50-12
Raytech Digital Winding Resistance meter WR50-12 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
product
Tools for FPC Connectors
The actuator opener is a tool that makes the Flex circuit connector actuator open quickly without using fingernails.
-
product
PathWave RF Sythesis (Genysys)
Analyze RF and microwave circuits and systems with fast simulation and powerful optimization tools. Explore performance trade-offs with automatic circuit synthesis technology. PathWave RF Synthesis (Genesys) provides entry-level functionality suitable for all RF and microwave circuit board and subsystem designers.
