Circuit
-
product
Multi Function Testers
Kyoritsu Electrical Instruments Works, Ltd.
Live circuit warning LED:Immediate illumination of a warning lamp if the circuit under test is live Auto Discharge:Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing Integral overload protection on internal continuity and insulation test circuitry Autoranging 500V DC test voltage for insulation tests 200mA short circuit current on continuity ranges Loop and RCD Testing Wiring connection check LED''s:Immediate indication if wiring of circuit under test is correct Overheat Protection:Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement Supply Voltage Indication:Can display supply voltage value in loop impedance mode Low Current Loop Impedance Test:Short duration low test current will prevent tripping of many passive RCDs
-
product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
8U 21 Slot VME64/64X Enhanced Crate
VME8100
short circuit protection, Over / Undervoltage protection, Over temperature protection. Remote monitoring and control take place through CAN bus, Ethernet, USB and RS232 interfaces. The crates are also SBC controlled via graphic OLED Display, provides Automatic Daisy Chain and supports Chained Block Transfers (CBLT). User-friendly control software completes the VME 8100 features. The Unit is powered by 92 ÷264 Vac, 50 ÷ 60 Hz, power factor 0.98% (230VAC).
-
product
PXI BRIC4 FIBO Matrix Dual 124x4 2pin Brkout
40-592A-014
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.
-
product
AC/DC Clamp Milliammeter (CE)
M-700
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current.*Suitable for measurement of 4-20mA DC controlled circuit.*DC mV analog signal output.*Lowest influence from Magnetization and Terrestrial magnetism.*Wide measuring ranges up to DC 1000mA and AC 10A.
-
product
LXI Series
LXI instruments range from LXI modules that plug into a chassis to standalone instruments that have dedicated LXI and hardware trigger bus connections. These instruments can be configured to measure many types of variables to precise values. Some of these instruments also incorporate 6.5-digit DMMs as well as user-programmable digital alarm circuits.
-
product
CPCI Test Extender 6Ux180mm
117FFE6018-0XXX
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
product
ASA101A
The ASA101A Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA101A you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board.With the ASA101A we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at a super-affordable price.
-
product
SPICE circuits & model Debugger / Analyzer
SpiceVision PRO
SpiceVision PRO takes the complex SPICE descriptions produced by many EDA tools and generates clean, easy-to-read transistorlevel schematics and circuit fragments, and design documentation to speed up debugging and project development.
-
product
Insulation & Multifunction Tester (LCD Display)
1153 AI
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Cable Detectors
With certain models of cable detectors you can locate open power cables, either live or dead (without current), with voltages up to 300V. Cable detectors can locate cables, circuits, short circuits and ground points. To perform these functions, it is not necessary to disconnect electrically sensitive devices or to disconnect theCable Detectors to locate open power cables, either live or without current, up to 300V power from the cable which is being tested. Cable detectors can also locate ferrous and non-ferrous metals, wood and plastic with a high level of accuracy.
-
product
Insulation & Multifunction Tester (LCD Display)
4102 MF
Standard Electric Works Co., Ltd
● Measures Insulation Resistance, voltage (AC-DC) measurements● Automatic hold facility.● Continuity test with a short circuit current of minimum 200mA.● MOV and Gas Arrester Testing.● Energy conservation is feature.● EnerSave™ limits the test duration to about 10 Seconds to save energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
product
Resonance Dip Meter
NRM-2
National RF’s Resonance Dip Meter is a test instrument used to determine the resonant frequency of a tuned circuit or resonant network, such as an antenna system. In addition, the unit may function as an RF detector, or a secondary frequency source. The instrument is analogous to the older vacuum tube “grid dip meter,” once popular in every electronic laboratory or radio station. Unique to this updated version is a buffered output that may drive a digital frequency counter for exact measurement of resonant frequency, or connected to an oscilloscope to be used as an RF detector and waveform/modulation monitor.
-
product
Linear Bench Power Supplies Local Control, Ultra Low Ripple/Noise
Series MSK
Kepco's MSK linear power supplies provide a selection of five models, offering 100 Watts of stable benchtop power. They use a high gain linear (series pass) stabilizer circuit for ultra low noise and low ripple output, good stability, and accurate resettability, and they are MIL-STD-461 compliant.MSK's "Preview" switch (d-c on-off) allows voltage and current to be pre-set with the digital meters displaying the set values. At "d-c off," no voltage is applied to the output terminals and no load current needs to be drawn to set the current limit. At "d-c on," the set voltage is applied to the output terminals, the appropriate mode indicator illuminates and the meters indicate actual voltage and current.
-
product
(70×90×15mm) C-Band DWDM Full Function Pre EDFA Module
WPA4300-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Huatai WPA4300-FM02 series with 70 × 90 × 15mm MSA compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 waves DWDM system applications.
-
product
Current Probe
PA-699
*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability
-
product
Voltage Testers
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
product
6-48V Digital Circuit Tester With Pierce Probe, Long Probe And Small Probe
1675D
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12, 24 and 48V systems.
-
product
Configurable OSAT Friendly Pick-and-Place Handler
Delta Eclipse
Eclipse delivers scalable performance for testing a wide range of semiconductors, from analog ICs to high-performance CPUs and mobile processors. The Eclipse is a high-speed pick-and-place handler designed to test up to 16 Integrated Circuits (ICs) in parallel, at temperatures from -45°C to +155°C*, with throughput up to 13,000 UPH.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-252-111
The 40-252-111 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
3U OpenVPX High Density Multifunction I/O Board
68CB6
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
product
Transistor-Level Defect Simulator
Tessent DefectSim
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
product
AC and DC 20-Amp Power Supply
ACDC-20
The ETI Model ACDC-20 is a rugged and portable 20-amp AC and DC power supply. Its applications include resetting circuit breaker charging motors and other general purposes. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1.92 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 2.8 kVA. The ACDC-20 is housed in a rugged plastic enclosure approximately 21.5” x 18.5” x 11.5” and weighs approximately 115 lbs.
-
product
Flying Probe Testers
SPEA’s Flying Probe Testers help manufacturers of printed circuit boards to deliver top-quality products in the fastest time-to-market, avoiding fixture cost and increasing accessibility when compared to bed-of-nails testers.
-
product
Filter Design Software
QuickFil
QuickFil is a software for designing passive electronic filters. The result is an optimized circuit of inductors (L)and capacitors
-
product
Receptacle Tester w/GFCI
61-501
*Warns against faulty wiring in 3-wire receptacles*For use on 120VAC circuits*1-year warranty
-
product
High Performance Programmable AC Power Source
61500 Series
Chroma 61500 Series have built in 16-bit measurement circuits and firmware utilities to measure the true RMS voltage, current, true power, apparent power, reactive power, power factor, current crest factor, and inrush current.
-
product
SIMRC - 16-Channel 1-Pole MUX, Screened Reed
1020-R-16-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Wire Sorter
Shanghai Beha Electronics Co., Ltd.
*Standard signal transmitter identifies up to 12 lines*Clear indication of short circuits, open circuits, or interruptions*Integrated continuity tester
-
product
Pulse Laser
Is a variable, pulsed high power laser source, a building block ideal for MOPA, LIDAR, OTDR laser systems development and applications. This fully integrated compact module contains a Distributed Feedback (DFB) laser and built-in optical amplifier stage, and a variable nanosecond pulse generation circuits. It provides up to 200 mW optical peak power in 1064 nm wavelength region, with a programmable pulse width from 10 ns to 1000 ns, and a selectable pulse repetition rate from 100 Hz to 1 MHz The optical pulse generation can alternatively be controlled via an external electrical trigger. In a compact design, NPL-CWDM-M is applicable for OEM integration or as a stand alone pulsed laser source. Contact Optilab for more information.
