Optical Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
-
product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
Optical Square
10777A
The Keysight 10777A Optical Square, used with Keysight straightness measurement optics, adds squareness measurement capability to the Keysight5530 Laser Calibration System. The optical square measures the squareness of axes during laser calibration of a machine tool. The Keysight 10777A uses two accurately-aligned mirrors to direct an output beam at precisely 90 degrees to an input beam.
-
product
High Voltage Linear Amplifier
A800X
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
product
40mA One-Channel Amplifiers
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
product
Optical Power Meter & VFL
TM263
◇ Self Calibration◇ Set the Auto Off◇ Wavelength Memory function after turn off the tester◇ High Accuracy, high ,High sensitivity, high linearity◇ Stable VFL Output◇ USB Charge port◇ FC,SC Connector◇ 18650Li-ion Battery◇ Lower power consumption design, long standby time◇ Rubber Out shell, increased the protective properties for field work
-
product
Handheld Optical Light Source
JW3116
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3116 Handheld Adjustable Light Source is Joinwit newly designed fiber optic tester, it aims at fiber network installation, fiber network engineering acceptance and fiber network maintenance. Combined usage with JW3216 handheld optical power meter, it offers a quick and accurate testing solution on both SM and MM fibers. The JW3116 provides 1 to 4 wavelengths and output power can be adjustable on customer requests. Also the JW3116 features good appearance, good touch feeling and considerate humanity design.
-
product
Optical Tables and Breadboards
At Kinetic Systems, we’ve taken the guesswork out of selecting optical tables and vibration control equipment. Our honeycomb vibration isolation optical tables provide cost-effective solutions for virtually any application. For extremely sensitive applications in severe or unknown vibration environments, we recommend our highly damped 5300 Series honeycomb optical table with Active-Air vibration isolation. For normal or moderate environments we offer economical, broadband-damped tables such as our 5200 Series or 5100 Series with either Active-Air Isolators or Modular Rigid Supports.
-
product
Fiber Optic Test
1 Piece/PiecesSupply Ability:10000 Piece/Pieces per MonthPort:For GuangdongPayment Terms:L/C,D/A,D/P,T/T,Western Union,MoneyGram
-
product
Fiber Amplifier - Node With Supply
FANS 811-812
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
product
Power Amplifier
The Model LN power amplifiers offer extended output power, voltage capabilities, lowdistortion, versatility and the latest BJT power in the operational amplifier technology. All theseperformance features are not available in other power amplifiers.
-
product
Amplifiers
The amplifier is one of the most important components in a pulse processing system for applications in counting, timing, or pulse amplitude (energy) spectroscopy, providing the pulse-shaping controls needed to optimize the performance of the analog electronics.
-
product
RF High Power Amplifier Modules
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
product
Switched Amplifier With Analog Detector Output
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
product
Gain Shape Linearizer Amplifiers
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
product
Fiber Optic Sensing Interrogator
RTS250+
This unit provides users with up to 200 Hz sampling rate for up to 4 fibers, which is twice the speed of our proven RTS125+, the unit that was created in partnership with NASA to support the test and validation of their new vehicles.
-
product
Optical Fiber Microscope
Connector-end face contamination is a problem that shouldn’t be ignored when it comes to fiber optic cables and patch cords. Allowing contamination to take place or fester will lead to network issues and down-time which you don’t need. For any fiber optic cable network, a high quality fiber microscope is a necessary tool to identify where contamination may be presenting.
-
product
Narrowband RF/Microwave Power Amplifier
While our broadband amplifier series are designed for multi-purpose, narrowband amplifier series may provide more appropriate solution for your specific needs. By narrowing the frequency range, smaller, lighter amplifier solution at more reasonable cost will be usually available.
-
product
Reticles, Optical Slits, Optical Apertures
With over 30 years of experience in the manufacturing of high precision Reticles, Slits, Apertures, and Pinholes, APPLIED IMAGE has gained a reputation for delivering precise and accurate parts. We have supplied thousands of these parts to be used in Day/Night Sights, Binoculars, Targeting Systems, Telescopes, Tank Sights, Microscopes, and many other Bore-Sight devices.
-
product
Amplifier Dyno
AD-1
The AD-1 Amplifier Dyno is a tool that is designed to be used any place an amplifier exists. It can be used in a lab or production line to test true amplifier power output, quickly and easily. It is simple menu driven, does not require a computer, and cannot be cheated as the load banks are internal. It can be used in an automotive audio install shop to test true amplifier output while the amplifier is installed in the customer's vehicle.
-
product
Optometers, Amplifiers, Display Meters
Optometers are a specific type of digital multimeter (DMM) used for optical radiation measurements. The particular light detector(s) connected determine the wavelength range/spectral weighting function and displayed measurement units.
-
product
Optical microscopy (OM)
Materials Analysis Technology Inc.
Optical microscopy is used to display the surface morphology of samples by 2D intensity contrast due to deflection and reflection of visible light shined on areas of interest. Its resolution is about half of the incident wavelength, which is ~0.2 μm for visible light (wavelength of 400-700 nm). Such resolution limits the maximum magnification to X1000, and thus optical microscopy provides preliminary inspection of sample surface structure.
-
product
Optical Equipment
It is intended for the organization of multiservice, hybrid, optical-coaxial cable networks. Years of development and research in this area have allowed Planar LLC to create a product line that covers the widest range of applications. All equipment is an outstanding example of the high technology of Planar LLC, each of the models is the result of intensive research and lengthy tests. This synthesis of technical sophistication and daily labor practically means that all equipment is highly reliable and exceptionally cost effective.
-
-
product
Dual Channel HV Amplifier with Phase Inverter
A400DI
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
product
Optical Fiber Ranger
OFR300
Shanghai Tarluz Telecom Tech Co., LTD
OFR300 Optical Fiber Ranger is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the OFR300 fiber ranger detect fiber faults location more accurate and easy.
-
product
Fiber Optic Tools
Shenzhen Sharingtek Communication Co., LTD
Are used to install, maintain, and test fiber optic cables, connectors, and networks. Fiber optic tools are essential for ensuring that fiber optic networks are installed and maintained correctly, so that they can provide reliable and high-speed data transmission.
-
product
Variable Gain Amplifiers
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a broad family of Variable Gain Amplifiers (VGAs) for RF, microwave, and millimeter wave applications. Our VGAs cover frequencies from 50 MHz to 40 GHz and are used in a variety of Network, Commercial and Aerospace and Defense applications. These products are available in industry standard plastic packaging and are designed for both 50 Ohm and 75 Ohm applications.
-
product
Handheld Optical Fiber Identifier
JW3306C/CT
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3306C Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification work, can be detect in any location of both SM and MM fiber. Meanwhile when you combined with JW3306CT Optical Signal Generator, which can realize low-frequency signal online injection, and also realize to find a particular fiber online without modulation signal in optical fiber signal .
-
product
Ultrafast Laser Oscillators and Amplifiers
Coherent ultrafast lasers are designed and manufactured to provide the best performance, portfolio and support in the industry.
