-
product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
product
LXI Microwave Matrix, 10GHz, Single 8x4 With Loop-Thru
60-750-184-A
The 60-750-184-A is a single 8x4 10GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
product
AC Power Source
6500 series
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
product
Scatterometer with Thin Film Measurement Capabilities
OptiPrime-X Series
The n&k OptiPrime-X series are automated metrology systems used to fully characterize and monitor Thin Film and OCD applications for both current and next generation IC processes.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-01
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
Particle Size Analyzers
Particle systems can be complex, but measuring them doesn’t have to be! Anton Paar offers two different technologies to characterize particles from the nanometer to the millimeter range. The Litesizer series employs light-scattering technology to determine not only particle size, but also zeta potential, transmittance, molecular mass, and the refractive index of nano- and microparticles in liquid dispersions. The PSA series uses laser diffraction technology to measure the size of particles in both liquid dispersions and dry powders in the micro and millimeter range. Side by side they open up a wide range of possibilities for comprehensive particle characterization.
-
product
PNA-X Microwave Network Analyzer
N5247B
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
InfiniiVision Oscilloscopes
3000T X-Series
100 MHz - 1 GHz, DSO and MSO models Speed testing with simplified operation and documentation enabled by the 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone Touch Triggering See the most signal detail with 1,000,000 wfms/s update rateQuickly modulate and characterize signals with built-in WaveGen 20 MHz ARB, 3-digit voltmeter and 8-digit frequency counter & totalizer options Decode serial busses faster with hardware-based serial analysis options Protect your investment with full upgradeability
-
product
Fully Portable Stand-Alone OTDRs
LOR-200
The LOR-200 is a family of fully portable stand-alone OTDRs. The instrument is integrated in a Windows XP based PC-platform with touchscreen interface.The LOR-200 is based on Luciol's novel scanning photon-counting technology (US patent #7,593,098). It achieves a superior dynamic range, and allows high resolution fiber characterization up to a total distance range of 160 km.
-
product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
-
product
Semiconductor Device Parameter Analyzer/Semiconductor Characterization System Mainframe
B1500A
Current-voltage (IV) measurement capabilities of spot, sweep, sampling and pulse measurement in the range of 0.1 fA - 1 A / 0.5 V - 200 VAC capacitance measurement in multi frequency from 1 kHz to 5 MHz and Quasi-Static Capacitance-Voltage (QS-CV) measurement capabilitiesAdvanced pulsed IV and ultra-fast IV measurement capability from minimum 5 ns sampling interval (200 MSa/s)Up to 40 V high voltage pulse forcing for non-volatile memory evaluation
-
product
Pilot VX
Pilot VX is a flexible, configurable flying Probe test system with an unrivaled set of technologically advanced tools, able to provide the test solutions required by the huge diversity which characterizes today’s electronics.
-
product
SystemSolutions
Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your yourdevice, not on your test system.
-
product
Analog/Linear Tester
Amoeba 4200
4200 is capable of running multiple test sites independently with a parallel efficiency of up to 85% for quad-site and octal-site testing.It comes with test development and production software suite, which makes the transition from test development and bench characterization to production seamlessly.
-
product
2D Near-Field Analysis of VCSEL Arrays
VTC 4000
Instrument Systems Optische Messtechnik GmbH
The VTC 4000 near-field camera from Instrument Systems was specially developed for the ultrafast, precise 2D analysis of VCSEL arrays. It enables polarization-controlled characterization of all relevant parameters simultaneously for the single emitters of the array.
-
product
Gross Alpha/Beta Measurement Systems
Gross alpha/beta measurement is one of the simplest radioanalytical procedures which are applied widely as a screening technique in the field of radioecology, environmental monitoring and industrial applications. This procedure has been developed to determine whether radionuclide specific analysis is required to further characterize the water. Regular measurements of gross alpha and gross beta activity in water may be invaluable for early detection of radioactive contamination and indicate the need for supplemental data on concentrations of more hazardous radionuclides.
-
product
Imaging Platform
TRITOM
The patented TriTom imaging platform is based on Photoacoustic Fluorescence Tomography (PAFT) technology that provides unparalleled capabilities for whole body imaging and in vivo characterization of small animal models.
-
product
Continuous Time Interval Analyzer - PXI
GT668PXI-40
A true breakthrough in high-speed Time Measurement and test technology, GuideTech’s GT668PXI-40 leverages the power of its CTIA continuous time-stamping technology, eliminating the need for supplemental triggers, pattern markers or clock recovery circuits.GuideTech’s CTIAs enables serial interfaces pattern verification and full jitter analysis in milliseconds for fast, automated characterization and high-throughput production test on all ATE platforms, including low-cost and in-house testers.GT668PXI-40 cards can be expanded up to 36 Channels Single Ended Input in a single 3U PXI chassis.
-
product
Digital Surface Resistance Test Kit
PAS-853BRM
- Surface Resistance Kit from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period control- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and point-to-ground (Rtg)- Measures resistance of Static Control Floors, ESD Work Surfaces and Packaging Material- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Conductive Rubber Electrodes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included
-
product
Thermal Conductivity Analyzer
TCi
The default C-Therm TCi Thermal Conductivity Analyzer employs the Modified Transient Plane Source (MTPS) technique in characterizing the thermal conductivity and effusivity of materials.
-
product
Low Leakage Switch Mainframe
B2201A
The B2201A reduces the cost of test by enabling characterization tests to be automated, with only slight compromise to the measurement performance of the semiconductor parameter analyzer. It supports a 4-SMU, full-Kelvin configuration and a capacitance meter, with room for future expansion. Includes 14 inputs, each with a unique internal measurement path, and a distinctive capacitance measurement compensation feature for two of the inputs. Provides front panel control via keypad or optional light pen, and supports instruments such as pulse generators.
-
product
SAM Premium Line
PVA TePla Analytical Systems GmbH
The SAM Premium Line combines acoustic microscopy and optical microscopy. It enables the scanner to be combined with both an inversion as well as a reflected-light microscope. The technology used in the SAM Premium Line is based on a core platform that employs the latest production and research technology. The individual systems are characterized by high throughput, high flexibility and a wide scanning range. They can be expanded to suit customer requirements and specified for the most diverse applications.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Modulation Distortion Up To 53 GHz
S95070B
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
product
X-ray Microscopy
Xradia Family
✔ Characterize the properties and behaviors of your materials non-destructively.✔ Reveal details of microstructures in three dimensions (3D).✔ Develop and confirm models or visualize structural details.✔ Achieve high contrast and submicron resolution imaging even for relatively large samples.
-
product
Optical Light Source
CARY-LS300B
The CARY-LS300B optical light source provide 1310/1490/1550 nm three outputwavelengths to meet specific application requirements. It is a idea solution for the fiberoptic network characterization, out-door network construction inspection and lab application.
-
product
Handheld Fiber Optic Light Source
Anfkom International Co.,Limited
3109 optical light source can provide 1 to 4 output wavelengths to meet specific requirements,including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber,as well as other wavelengths according to customer needs.Together with the 3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
-
product
Keysight N7800A Test Management Environment (TME) Software
Special recommended calibration options: The N7800A software calculates point-to-point ISO GUM measurement uncertainty. The special “H-series” calibration options in the link below provide lower measurement uncertainties through use of direct comparison to devices directly characterized by NPL or NIST (or another NMI), along with data on a CD for easy import into the N7800A (avoids manual entry). The overall resulting N7800A measurement uncertainty then incorporates this lower device uncertainty in the overall calculated uncertainty. For more information on the special options please view this spreadsheet N7800A Special Calibration Matrix.
-
product
TF Analyzer
The TF Analyzer platform is the heart of the modular and flexible measurement systems for the characterization of piezoelectric materials.
-
product
PCI Express 4 CEM Receiver Test Automation
N5991PC4A
The N5991PC4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 4.0 CEM Add-In Cards and systems
