-
Product
Optical Performance Monitor
-
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
Product
Monics®
-
Kratos Defense & Security Solutions, Inc.
Monics is the industry leading carrier monitoring and interference detection product used by the majority of the of the world’s largest satellite operators, service providers and telecommunications providers to monitor over 200 sites in 60 countries around the globe. Monics helps operators effectively see what is happening with their communications payloads and protect bandwidth and Quality of Service (QoS), while optimizing staff utilization and minimizing costs.
-
Product
PXI Waveform Digitizer
PXD731x/70xx
Waveform Digitizer
Digitize high-resolution waveforms with the fully isolated PXD Series digitizers. Minimize interference and measure "in-circuit" within circuits. Measurement errors are reduced by a high input impedance.
-
Product
High Range UV Fluorescence SO2 Analyzer
Model N100H
-
Teledyne Advanced Pollution Instrumentation
The Model N100H instrument uses the proven UV fluorescence principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high range SO2 gas. The instrument includes interferent rejection, providing a simple and precise solution for a broad range of continuous emission monitoring systems (CEMS) and stack testing applications.
-
Product
Signal Analysis
Synchronous Accumulation (Order Analysis)
-
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
Product
Monics® SatID®
-
Kratos Defense & Security Solutions, Inc.
Kratos’ leading RF interference geolocation product, satID® provides an accurate, fast, all-in-one solution for locating and identifying sources of interference, including VSAT/TDMA terminals. With the capability to geolocate within 5 km of the interfering signal, satID is the most accurate geolocation product available today.
-
Product
Spectrum Monitoring Software
-
A comprehensive set of tools for spectrum monitoring, interference analysis, signal identification and geolocation
-
Product
Lightning Rod Flaw Detector
PADD
-
We developed the PADD for the detection of internal and external partial discharges on metal oxide lightning rods. Defects can cause radio interference in communication systems or TV images, interference whose origin is very difficult to locate. We have developed a unique technology for detecting radio frequencies for use under voltage.
-
Product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
-
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
Product
DDLS 200 with 2 Mbit/s Transmission Rate
-
Leuze electronic GmbH + Co. KG
Optical data transmission for RS interfaces and fieldbuses up to 300 m and up to 2 Mbit/s. Infrared data transmission protects the DDLS 200 from interference. Systems are available for all common industrial fieldbus interfaces. The ranges are stepped and reach a maximum transmission distance of 300 m. Low ambient light sensitivity through special FSK method. Available interfaces: PROFIBUS, Interbus and CAN/DeviceNet, as well as RS422 and RS 485.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Basic Threaded Probes (F723, F733, F734, F735, F737) H733LARDS1
1022713
-
The Basic Threaded Probes (H733LARDS1) are designed for precision in electrical testing and measurements. This model, part of the H733 family, ensures a reliable connection with a flux-proof solder type that minimizes the risk of interference. Crafted with meticulous attention to detail, these probes come with a total length of 27mm and a collar height of merely 0.2mm, making them ideal for systems where spatial constraints are critical.
-
Product
USB 3.1 Interface Module
-
Super speed “USB 3.1 type C modules” for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for USB 3.1 link untouched.
-
Product
Interference & Compatibility Evaluation System
ICEy
-
Schmid & Partner Engineering AG
ICEy is the most advanced reactive near-field E/H-field scanning system for the analysis of EM interference and compatibility (EMI/EMC) in highly integrated electronics. ICEy is the only system that provides accurate EM measurements traceable to international calibration standards and also allows independent interlaboratory comparability of EMI/EMC measurement results.
-
Product
Active Dual Loop Antenna
KH30936
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
Product
Blockage Locators
-
Shenzhen Noyafa Electronic CO.,LTD
Noyafa Blockage Locator can be used in both household and engineering. The sensing range is enhanced, and it is free from external interference. It can pass through the 60cm-thick cement wall and the pipe blockage under the floor to reduce the removal area. Accurate detection and adjustable sensitivity.
-
Product
WiFi Traffic Generators
LANforge WiFIRE
-
wireless traffic generator is an excellent choice for testing Access Points and other WiFinetworks. The CT520 uses a modified Wireless driver for WiFi NICs based on the Atheros chipset. It cansupport up to 32 Virtual Stations. Each of the Virtual Stations has its own IP address, IP port space, MACaddress and routing table. The Virtual Stations can be assigned to communicate to a particular AccessPoint, use a particular SSID, and have a WEP (64 or 128bit) or WPA/WPA2 key assigned. More advanced802.1X authentication is also included. There is a single WiFi radio per CT520 but multiple LANforgesystems can be clustered together for more realistic radio interference patterns and increased trafficgeneration capability. The radio supports 802.11 a, b, g or n mode. Transmit power andchannel/frequency is configured on a per-radio basis. Most other settings are configurable per virtualstation
-
Product
Trace-Level UV Fluorescence SO2 Analyzer
Model T100U
-
Teledyne Advanced Pollution Instrumentation
The Model T100U Trace-level SO2 analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven UV fluorescence principle, and is designed to allow ultra-sensitive SO2 measurements while still meeting the requirements for use as a US EPA compliance analyzer.The analyzer uses both the light and dark phases of the pulsed UV light source to continuously detect and correct for electronic noise, giving exceptionally stable and sensitive performance. A separate UV detector allows the instrument to continuously correct for variations in lamp intensity. Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift, and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon "kicker" and advanced optical design combine to prevent inaccuracies due to interferents.
-
Product
UltraTEV Plus
-
The UltraTEV Plus is the latest innovation being introduced to the award winning UltraTEV range. This easy to use instrument incorporates additional sensing capabilities and real time advances analytical features enabling you to distinguish between true PD, noise and other interference allowing you to make better decisions while saving time and money and enhance the safety of your staff and your network.
-
Product
Parallel NTDS Isolation Tap Box
-
IXI’S NTDS parallel isolation tap box is the ideal solution for relibility tapping NTDS parallel type A, B, C, and H interfaces. It connects easily to existing cables forming a tee connection that can be used for data monitoring and acquisition over long distances without interference with your system.
-
Product
IEC 61000-4-5 EN61000-4-5 Lightning Surge Tester, Surge Generator
506AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
Automatic lightning surge generator (or Lightning surge immunity) is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Miniature Fiber Optic Pressure Transducers
-
*The diameter of the working length section can be as small as 0.5 French *The sensor tip size can be as small as 0.8 French The flexibility of the glass fiber offers excellent deliverability without being prone to kinking like electrical wires *The front looking configuration of the sensor tip prevent side-facing/wall bouncing artifacts in the measurement*The lack of metallic components provide full immunity to interference from RF, MW and MRI systems
-
Product
Shielded Rooms
-
HIGHVOLT Prüftechnik Dresden GmbH
Electromagetic field and line-conducted interference needs to be eliminated in order to measure low-intensity partial discharges with a PD background noise level (≤ 1 pC) in accordance with IEC 60270.
-
Product
Tunable Edge Filters
-
Tunable edge filter is a customized product. It usually belongs to 2-port optical tunable filter product platform. Instead of using narrow bandpass filter in the 2-port tunable optical filter, the tunable edge filter utilizes a low-pass or long-pass interference filter. By changing the incident angle of the light beam, the cut-off wavelength will be tuned. Standard Tunable edge filters support C-band or L-band wavelength range.
-
Product
Optical Channel Monitor
-
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
Product
Absorbing Clamp
AB-CLP
-
• EMI Receiver equipped with absorbing clamp can indirectly test radiated interference power of household electrical appliance, power tool and similar electrical appliance with frequency from 30~300MHz.
-
Product
Detectors
-
Solar blind detector for operation in the 1 to 180 nanometer region. It is encased in a vacuum tight housing for vacuum operation. The Model 425 is ideal for measurements in the Extreme and Vacuum UV (EUV and VUV) where the solar blind feature eliminates potential interference from long wavelength ultraviolet and visible light. It may be operated in pulse-counting mode or DC. The CEM is also available with coatings like Cesium Iodide or Magnesium Fluoride to enhance response in different energy regions.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Dynamic 9D Ladar
-
DYNAMIC 9D LADAR provides micron-level resolution while eliminating issues associated with surface reflectivity, slow data acquisition speeds, limited accuracies, restrictive incident angles, and susceptibility to production environment noise.Laser Radar systems require large sample averaging to obtain reasonable accuracy, effectively slowing data rates. API’s OFCI technology uses fast laser chirping to generate a wide spectrum for optical interference. The interference signal detected yields 100x higher sensitivity than Laser Radar.
