Filter Results By:
Products
Applications
Manufacturers
-
product
Interior Wiring Testing
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
product
Trailer Light Testers
Pro-Check 725
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
product
Ultra-Compact Testers
adaptronic wiring testers of the ultra-compact class are available as low voltage testers and also as high voltage testers, as KT version with display and keyboard and as NT version with the grafical user interface NT Control.
-
product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
LAN Tester
TVR10/10/100
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
product
NI-9976, 2-Pin, Male COMBICON to 2-Pin, Female Screw Terminal Block Plug
196739-01
2-Pin, Male COMBICON to 2-Pin, Female Screw Terminal Block Plug - The NI-9976 consists of a bag of 10 screw terminal plugs for any 3- or 4-channel 2-position screw terminal C Series module. These terminal plugs provide direct connectivity to the module. All C Series modules ship with the required connectors, so you can purchase the NI-9976 to reduce wiring on multiple devices or use for spare replacements.
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
High Altitude Wiring Clamp
Weshine Electric Manufacturing Co., Ltd
1. The operation is simple, through pushing and pulling the special operation lever can realize the clamp mouth free opening and closing, complete the wiring work.2. Connection clamp between the upper and lower jaws of the use of the principle of moving pulley to save the effort, the use of smaller tension can be obtained larger clamping force.3. There is a steel needle inside the clamp mouth to ensure good contact between the clamp mouth and wiring position
-
product
Microwave Coaxial Cable Assemblies
MWX0 series
JUNFLON® MWX products are flexible signal transmission lines that take advantage of the remarkable properties of fluoropolymers. They are suitable for use with a wide range of frequencies up to 67 GHz. These products feature low insertion loss and low VSWR, low signal leaks and low interference due to high shielding effectiveness, and higher density wiring for use in the narrow device interiors. Junkosha provides highly reliable products for microwave /millimeterwave applications tailored to customer assembly needs.
-
product
ITA, ICon, With Protective Cover
410123101
The iCon ITAs small width and inboard handle allow for easy side-to-side stackability. The u-shaped cable clamp allows modules to be pre-wired before assembly and offers a maximum cable bundle diameter of 1.21". The slide-off cover allows easy access to wiring for maintenance and probing.
-
product
CAN FD/CXPI Communications Expansion Kit
OP-SB87FD
OP-SB87FD is an expansion board for LE-8200A/LE-8200 used for monitor/simulation of CAN (ISO 11898-1), CAN FD (ISO11898-1:2015), and CXPI (JASO D015). With this kit and the line state sheet, LE-8200A/LE-8200 works as a stand-alone type analzyer for CAN, CAN FD, and CXPI. The board supports development of CAN (used for automotive industry and other industries), CAN FD (next-generation standard of CAN providing more high-speed and communication capacity), and CXPI (invented in Japan to replace direct wirings) devices.
-
product
PCI Termination Products
Acromag provides a broad selection of hardware accessories to simplify the use of our I/O boards. This collection of panels, cables, and adapters facilitate field wiring and cable connections between boards within the card cage. Select from an assortment of cables and termination panels to simplify wiring and installation.
-
product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
Strain Relief Plate, Receiver, iCon
310113456
The strain relief attaches to the wiring side of the iCon receiver and can be secured before receiver installation. The strain relief is made of aluminum and black powder coated and includes 6 wire ties.
-
product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
product
Cable Tester
KT-468
Test device used UTP and STP network wiring and phone line. Check continuity and configuration of wiring with unshielded and shielded modular plugs. Test for open circuits,shorts,miswires and reversals. SHIELD detection tests a cable`s shield integrity. Main unit and one remote allow one person testing
-
product
Signal Isolators
Signal IsolatorsDatexel manufacture a large range of Signal Isolators. The DAT511 is a loop powered isolator with 3000 V galvanic isolation between the input and output. It is a 2 wire device so there is no external wiring. The DAT511H is similar but is Hart compatible. The DAT4035 is a universal input signal (Thermocouples, RTD's, mV, Volts, mA, resistance and potentiometers) conditioner with 2000 V isolation between the input and output and it is PC programmable. It is a 2 wire loop powered device. The DAT4135 is similar but it is a 4 wire device so it has the ability to boost the output or provide a voltage output.
-
product
GFCI Socket Tester
TEL5
Standard Electric Works Co., Ltd
● Fast, easy wiring check.● Easy to read light indication.● Confirm the correct wiring of AC socket.● Test GFCI for correct wiring & operation.● Detect 5 wiring faults.● GFCI circuit trips to confirm the tester is working.● The testing current for GFCI is about 8mA.
-
product
Linear Actuators DPDT Switches
DPDT
Most Thomson actuators require at a minimum the use of a double-pole double-throw remote switch. To better assist our customers, we provide two versions of a DPDT switch (with or without enclosure) to work directly with our actuator units. A wiring diagram label and an "OFF" center position are included.
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Wireless Functional Test Fixtures
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
product
Cable 96-Pin Female to 100-Pin Male Micro-D, 2m
40-973B-096-2m-FM
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
product
Electrical Insulation Tester Kit with Dual Display
420001
When undertaking power installations, the 420001-insulation tester can provide special help to test wiring. This unit can provide 125V,250V, 500V and 1000V source for the test, and under each range it can supply 1mA current to feed the capacitance load. With the auto-range function, it can measure up to 4,000 Megaohm with the resolution of 1Kohm.
-
product
HMIs And Annunciators
Schweitzer Engineering Laboratories, Inc.
HMIs and annunciators improve situational awareness, efficiency, and safety by providing local indication of alarm conditions. Integrating these devices with remote I/O, relays, or real-time automation controllers eliminates duplicate I/O wiring.
-
product
100 Pin Micro-D Cable, Male To Male, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9B200
This 2m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
product
Compact Differential Pressure Transmitters
Series 668B/D
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
product
9050 Slide Mount
The 9050 Slide Configuration provides maximum test system versatility. This configuration allows for easy instrument wiring and chassis access which allows for shorter cable lengths and a flush rack mount to save valuable work space.Ordering has been simplified with packages offered that include the 9050 receiver, receiver mounting plate, flanges and instrument bracket. Slide kits are available in depths designed to fit most common racks. To determine the slide kit needed, measure rack depth between mounting rails. Slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures.
-
product
Isolated Controller Area Network (CAN)
ADI isolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
product
Saluki S2107 Series Optical Cable Identifier (up to 36dB)
S2107 Series Optical Cable Identifier is an intelligent instrument designed for the construction and maintenance of optical cable lines in optical communication system. In view of the complex wiring environment and the difficulty of locating faults during the construction and long-term use of optical cables, S2107 series can provide fast, effective and accurate fault solutions. When the target optical cable is bent or shaken, the optical cable census instrument can quickly capture the vibration signal and display it through waveform and sound, so as to locate the target optical cable quickly.
