Conducted Immunity
EUT's resilience to an injected disturbance through associated cable.
See Also: Immunity Test, Coupling Decoupling Network
-
Product
Conducted Immunity Test System
-
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
Product
Conducted Immunity Test Systems
-
Conducted Immunity System (CIS) to Test According to IEC 61000-4-6. The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
Coupling Decoupling Network (CDNE)CDN
Emissions
-
CDNEs are based on the CDN as specified in IEC61000-4-6 (Conducted RF Immunity test). In this test, the CDN is used for the coupling of RF onto a cable. In principle, the CDN can be used in reverse, ie coupling any RF on the cable out to an analyser. In an earlier version of EN 55015, these CDNs were specified as suitable for measuring emissions. However, the current version of the standard specifies a CDNE which is essentially a CDN refined to deliver higher accuracy particularly at higher frequencies.
-
Product
EMC Testing Services
-
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
Product
EMC Testing Knowledge & Equipment
-
Creating, delivering, installing, and training on EMC test systems; RF Immunity systems, RF Radiated and Conducted Emissions systems, Conducted Immunity and Pre-compliant EMC systems.
-
Product
Electromagnetic Immunity Scanner
SmartScan 350
-
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
Product
Conductivity Meters
-
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
Product
Conductivity Sensor
ACF60-35
-
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity sensor fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
EMI EMC test Solutions for Immunity
-
Scientific Mes-Technik Private Ltd
EMI EMC test Solutions for Immunity
-
Product
Conductivity Sensor
-
Conductivity sensors from Aanderaa are compact, fully integrated sensors for measuring the electrical conductivity of seawater. Conductivity is a key parameter for in-situ measurements of several fundamental physical properties of seawater.
-
Product
Benchtop Conductivity Meter
LAQUA EC2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Portable Conductivity Meters
-
Labodam portable conductivity meters are adapted with different modes for measuring quality of water on parameters such as conductivity, TDS, and temperature. Due to their portable design, they are suitable for outdoor measurements i.e. on site water testing, remote area water testing, and for research purposes. They are reliable and user friendly.
-
Product
Carbon Sensor Conductivity Meter
HE-960LC
-
Can measures conductivity of low concentration. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960LC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
Product
Software for Immunity Test METES-EMS series
-
METES-EMS is software for Automated Test Solution to meed Immunity Std. each for Keys : Support for latest Windows OS Access via USB/LAN interface to measurement equipments to achieve
-
Product
Water Conductivity and Temperature Probe
CS547A-L
-
The CS547A is a water quality probe that measures both electrical conductivity (EC) and temperature. It connects to a Campbell Scientific datalogger via the A547 interface. This probe is compatible with most Campbell Scientific dataloggers.
-
Product
Liquid Thermal Conductivity Instruments
THW-L1
-
The Transient Hot Wire (THW-L1) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity, thermal diffusivity, and specific heat instrument for measurement of liquids and pastes in accordance with ASTM D7896-19. The THW-L1 was designed with speed and operational simplicity in mind. With a single measurement of 1 second in duration, small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity, thermal diffusivity, and specific heat. The THW-L1 utilizes a non-stationary measurement approach and rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a thin heating wire 40 mm in length and is completely inserted into the sample to be tested.
-
Product
Pocket Conductivity Testers
-
Labodam pocket conductivity testers are equipped with platinum sensors and 1 point brush calibration system. These easy to use pocket conductivity meters come with waterproof design features for protection against harsh conditions. The conductivity meters can be used for measuring the conductivity of drinking water, waste water, brine water, and liquids with high, low conductivity.
-
Product
Battery Conductance Tester
SAT-AC
-
Shaanxi Aitelong Technology Co., Ltd
SAT-AC Battery Conductance Tester is a multi-function and portable digital data storage measurement instrument to test battery running condition and parameters quickly and precisely. It can display and record many key parameters for multi-groups like battery string and each battery cell’s voltage, conductance, connecting strip resistance, battery’s internal resistance and so on; offer the ability to distinguish battery’s condition effectively and accurately; compose with intelligent PC measurement analyzing software, user can track battery’s decay trend, and alarm beforehand to help technician and administrators process according to status.
-
Product
PH/ORP, Conductivity, Oxygen & ISE Meters
-
As one of the leading brands for laboratory and field measuring instruments, WTW develop solutions that are used worldwide in drinking and waste water treatment, environmental monitoring, research and industry. The portfolio ranges from high-precision benchtop meters for the laboratory to robust handheld meters for mobile use and complex multi-parameter systems. Whether pH value, conductivity, dissolved oxygen or ISE - our devices deliver reliable and standard-compliant results even under the most demanding conditions.
-
Product
Multifunctional Immunity Test System For Automotive Electronics
EMS-ISO7637
-
EMS-ISO7637 automotive multifunctional immunity test system meet newest ISO7637-2 requirement of
. This standard was issued by international organization for standardization, and this system included all of ISO-7637 required test waveform and meet most of automotive manufacturer’s requirement for automotive electronic immunity test. -
Product
Thermal Conductivity Apparatus
-
Objective Thermal Conductivity of Liquids & Nanofluids & Engine Oils etc.
-
Product
Electromagnetic Immunity Scanner
SmartScan BASIC
-
The BASIC is manually operated system for performing susceptibility scanning at the system level with minimal data storage capability. This system includes:1. Up to 8kV (optional. 4kV base) pulse generator for ESD susceptibility testing- Camera and camera shutter to take DUT picture and failing spots- Control computer2. Up to 8kV Probe Sets:- 1mm Hx/y Field Probe- 5mm Hx/y Field Probe- D=8mm Hz Field Probe- D=8mm Ez Field Probe- Contact API for custom design probes3. Manual input of testing location and failing condition over the DUT to be included in final report.
-
Product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
-
Compact handheld device for measuring the electrical conductivity of non-ferrous metals.
-
Product
Conductivity and Temperature Water Pocket Meter
LAQUAtwin EC-22
-
The only pocket meter that directly measures conductivity in 0.12ml sample. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
Product
Battery Conductance Tester
FST-8000
-
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
Product
Conductive Anodic Filament Testing
-
AutoCAF™ is able to measure up to 256 individual measurement sites under conditions of high humidity and temperature in accordance with IPC-TM-650 2.6.25 Test Method & IPC 9691 CAF Test Users Guide.
-
Product
12V Conductance Batter Tester
MBT100
-
Tests 12V starting/charging systems, including flooded lead acid, AGM, and gel cell batteries. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries.
-
Product
Conductivity Probe
ACS60-35
-
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity probe fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
