Conductivity
-
Product
Universal Converter
C8000
-
Multi channel converter for all optek photometric and conductivity sensors and electrochemical pH electrodes. Flexible configuration of sensors, measuring ranges, units and product specific setups make the C8000 converter series a powerful device in process monitoring in both conventional and single-use systems.
-
Product
DCDC
FC Series
-
The FC Series are ultra-low noise, high performance DC/DC converters that are packaged in low profile (0.4 inch high) cases. Essential quality performance features are designed and built-in. A high performance Pi input filter minimizes input reflected ripple, while 5-sided electrostatic shielding and tape-wound toroids, rather than pot cores, minimizeradiated EMI. Advanced circuit design techniques reduce conducted output noise in the form of current spikes, to an extremely low level.
-
Product
Automated Titration Analysis Systems
-
MANTECH is a leading manufacturer of multi-parameter and titration analysis systems. We can deliver custom analysis systems that perform the following functions: pH, Chloride, Oxygen, Turbidity, Alkalinity, Fluoride, Oxidation-Reduction Potential (ORP), Nitrate, Electrical Conductivity, Color, Salinity, Total Hardness, Acidity, Ammonia, Temperature and Soil pH & Conductivity.
-
Product
Battery Chargers
-
DC Battery ChargersStep-Up & Step-Down DC Source Chargers and Equalizers These units provide up to 600 watts to charge a 12V or 24 V battery systems (1 or 2 banks) from a 12, 24, 32 or 36 volt source. The single-board design incorporates state-of-the-art switch mode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. All Series are capable of charging up to two independent banks of batteries.
-
Product
Limiter
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The series of products‘ limiting ability can be achieved by the diode conduction and cut-off characteristics.The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of low insertion loss, small size and high reliability. The products can be applied to receiving channel low noise amplifier protection in radar system. KeyLink's limiters can be categorized as follows.
-
Product
PRO Conductivity (EC) Controller and Pump Kits
MC745
-
The Milwaukee MC745 PRO Conductivity (EC) controller and pump lets you measure and adjust EC levels automatically.
-
Product
Pin Grips For Flat Specimens
-
Pin grips are very user friendly and are designed for conducting tensile tests of hard metal plate specimens that are difficult to grip. Specimens are held within the grips by passing pins through holes in the specimens.
-
Product
Cable Testers
-
Can be used to fast check if Ethernet/telephone/BNC/HDMI cables are conducting, short-circuit, crossed or open-circuit. They are ideal tools for technicians to install, maintain and inspect week current system circuit.
-
Product
IsoPods: Streaming Meters For Recording Temperature, PH, Conductivity And Dissolved Oxygen
-
eDAQ isoPods™ are portable streaming data recorders. These electrically-isolated meters can be used for recording data in situations where signal noise and crosstalk would otherwise be an issue.
-
Product
Software Compatibility Testing Services
-
ImpactQA uses compatibility testing to ensure interoperability between your business-critical systems to discover important modifications or additions required. Following functional necessities, we offer solutions so that our clients could avoid loss of reputation and financial risks caused by poor system compatibility. Testing conducted before the product releases identify compatibility glitches and controls project budget over the prescribed limits. ImpactQA offers an end to end compatibility testing services and infrastructure to make sure your apps deliver for your users and your business.
-
Product
Regenerative Grid Simulator
61800 series
-
Market demand for Distributed Resource (DR) products such as PV inverters and wind energy systems is steadily growing as the world strives for clean renewable energy sources. This demand has created a need for rigorous regulation testing to standards such IEEE 1547 / IEC 61000-3-15 / IEC 62116 ensuring proper and safe operation of on-grid products. It has become critical to manufacturers to conduct these tests to prove compliance and to relieve product liability concerns. Chroma’s new 61800 family of Grid Simulators has been designed to fulfill these test requirements by providing a full 4 quadrant, fully regenerative, grid simulator with advanced features for compliance, safety and product verification testing.
-
Product
Temperature & Humidity Chambers
-
Canden Reach-in stability chamber models -Q20,Q40,Q60 is designed to conduct stability testing on pharmaceutical products in accordance with the guidelines set by the FDA/ICH. These chambers play a crucial role in assessing the long-term stability, quality, and shelf life of pharmaceutical formulations.
-
Product
High Temperature ICP® Accelerometers
-
PCB® offers specially designed and tested ICP® accelerometers for conducting vibration and shock measurements under demanding environmental conditions of up to 356 °F (180 °C). These sensors combine proven quartz and ceramic shear sensing technology with specialized, built-in microelectronic signal conditioning circuitry to achieve dependable operation in extreme temperatures and through repetitive temperature cycling. Laser-welded, hermetically sealed, lightweight titanium or stainless steel housings offer further protection from the environment. Prior to shipment, each sensor undergoes a battery of tests to ensure survivability for its intended use. Such tests include temperature soak at elevated temperatures, temperature cycling, and exposure to highly accelerated screening procedures with hydraulically actuated shakers.
-
Product
Dopant
-
In semiconductor manufacturing, electrical performance starts with atomic-level control. Dopant technologies make that possible by introducing carefully measured doping constituents that help devices conduct, switch and perform reliably. For precise control of fluxes for Molecular Beam Epitaxy (MBE) dopant constituents, or for gases that do not require thermal cracking, Veeco’s Dopant products are ideal.
-
Product
PXI 3A Power MUX BRIC, 12-Channel, 12-Pole
40-571-303
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
150 kHz-230 MHz Broadband Power Amplifiers
-
Output power up to 80W for standard conducted immunity testing. Our 150 kHz-230 MHz amplifier range covers output power ranging from 20 W to 80 W.
-
Product
Fittings
-
Specialized, removable connectors and housings used to securely mount sensors (for pH, ORP, conductivity, or oxygen) into pipes, tanks, and reactors.
-
Product
Light/Laser Flash Analyzers
-
Light or laser flash is a measurement technique used to determine the thermal diffusivity, thermal conductivity, and specific heat capacity of materials. Light flash measurements are essential for characterizing the heat transfer and storage properties of a variety of materials, whether the sample of interest is expected to insulate, conduct, or simply withstand temperature changes.
-
Product
Process Analyzers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Industrial meters for pH, ORP, conductivity and oxygen. In 2- and 4-wire technology, explosion-proof.Bus Communication: HART, FOUNDATION Fieldbus, Profibus DP and PA. Robust industrial housing with high IP protection. Suitable for outdoor use. For analog and digital sensors. Simple intuitive operation. From DIN rail transmitters up to the modular system.
-
Product
Food Analyzers
-
The function of the milk analyzer is to make quick analyses of milk on fat (FAT), non-fat solids (SNF), proteins, lactose and water content percentages, temperature (oС), pH, freezing point, salts, conductivity as well as density of one and the same sample directly after milking, at collecting and during processing.
-
Product
3U VITA 62 Power Supply Module, 300W With Hold Up Power, Conduction Cooled
064-112
-
Designed to VITA 62, this 3U x 9HP DC power supply module is conduction-cooled and provides up to 50ms hold-up time and a BIT controller.
-
Product
32-Channel RS485/422 Differential
4792
-
The Conduction Cooled 32-channel Reconfigurable RS422/RS485 Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring a differential interface. Thirty-two (32) generalpurpose RS422/RS485 driven digital I/O differential pairs are wired to the rear PN4 connector. For each of the 32 channels, the bidirectionality is controlled by an output from the FPGA.
-
Product
SM / Expansion Unit
-
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
Product
Sensor String System Flexible Subsea Observatories
SeaGuard Sensor String
-
The Aanderaa SEAGUARD® Sensor String Systems are complete and flexible subsea observatories for measurements of e.g. dissolved oxygen, conductivity, temperature, current, pressure and tide.
-
Product
Seawater Refractometer
AQUAR-H5O
-
The Palm Abbe AQUAR Digital Seawater Refractometer is a professional refractometer for testing seawater, salt water, and brackish ocean water for oceanography, aquaculture, aquariums, desalination plants, and ocean research. The model AQUAR-H5O measures seawater salinity in Practical Salinity Units (PSU), Sigma-t Density, Specific Gravity, Conductivity, and Chlorinity.
-
Product
Flow Through Fittings
-
In-line or bypass housings designed to securely hold, protect, and position analytical sensors (pH, ORP, conductivity, oxygen) directly within a fluid process stream.
-
Product
Battery Boxes Testing Equipment
-
Battery boxes can be tested for faults by placing the box on a metal plate. By applying a test voltage to an electrode inside the box, the moulding can be checked thoroughly - particularly at the injection points - and any faults found. Defects will be identified by a spark passing from the electrode, through the defect itself, to earth (the conductive material placed outside the battery box.
-
Product
Electrical Impedance Tomography
-
Electrical Impedance Tomography (EIT) is an imaging technique that visualizes conductivity or impedance distributions both in 2D and in 3D. Sciospec is partnering with world leading scientists in the field to deliver solutions that enable using EIT both in research and in practical applications.
-
Product
Probes, Clamp-On
EM-6980 | 20 Hz – 50 KHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
VPX Extender 3U VITA67.1 Conduction Cooled
1940000519-9001R
-
3U VPX Extender for conduction cooled boards mounted in conduction cooled chassis VITA 67.1 (VITA 67.1 connectors not included)
