Polarization
property of transverse waves which specifies the geometrical orientation of the oscillations.
See Also: Resistivity & Induced Polarization, Resistivity, Polarizers
-
product
STDETransformer Demagnetizer
STDE
This option allows neutralizing the residual magnetization of the power transformer core after the winding resistance test. The principle of the option is to apply a constant current of alternate polarities to the transformer winding, as per the IEEE 0062 1995 standard.
-
product
Chamber/Pyroelectric Task
Radiant's Chamber/Pyroelectric Task sets the sample to a series of temperatures by performingGPIB control of an external thermal device. At each temperature it captures the sample’s polarization response and/or small-signalcapacitance. These are combined to calculate the pyroelectric coefficient. The Pyroelectric Task is to be used with a Radiant Test System and a Linkam Stage (-196C to 600C), Thermal Chambers, Hot Chucks, or a Furnace to automatically measure the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled. Radiant's Pyroelectric measurement Task can be added to Vision at additional cost. This measurement suite fully characterizes the pyroelectric charge (polarization) response of the sample under test. The Pyroelectric Task suite controls various thermal controllers such as Quantum Design, Lake Shore, Delta Design, and many others. Detailed Listing of Thermal Controllers Registered in Vision. The Chamber/Pyroelectric Task is quoted upon request.
-
product
Log Periodic Antenna
ZDS7-1-6G-832
Log Periodic Antenna, Frequency 1~6GHz, Gain 9dBi, VSWR 2.5, Linear polarization, N-Female
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Fiber Optic Components For Optoelectronic Packaging
OZ Optics offers a wide range of standard and custom fiber optic components for optoelectronic packaging. Components include collimators, focusers, patchcords, connectors, and metalized fiber. The low backreflection collimators and focusers are available for a wide range of industry-standard connectors and wavelengths. The hermetically sealable patchcords, with glass or metal solder, and metalized fiber meet high Telcordia standards. The polarization maintaining patchcords and connectors use our specially designed ferrules that minimize insertion loss, backlash, and rotational errors.
-
product
Cross Hole Energizer P/S
CHE
Specially designed for small-scale cross-hole surveys, this compact hammer can be used to generate both P and S waves.The hammer can be downloaded using the steel cable and clamped to the requested depth by a pneumatic clamping system manually controlled by a lever from the surface; simply pushing up the steel cable to execute the first shot, the trigger installed on the energizer will start the acquisition for the “P/S”. After that you will have to drop the mass to make the acquisition with inverse polarity.
-
product
PXI Solid State Multiplexer, 10 Amp, Dual 3-Channel
40-666A-011
The 40-666A-011 is a dual 3-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI Solid-State Matrix Module, 6x2, 10 A
40-553A-011
The 40-553A-011 is a high current 6x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each matrix switching path can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Digital RCD Tester
1113 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Very low consumption.● 50Hz and 60Hz operation.● Accurate digital readout of disconnection time.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Auto power off. ● Backlight function. ● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
product
Digital Circuit Tester 3-49V
28830
Operating range of 3-49 volts DC to work on most vehicle electrical systems. 360° visibility of polarity. The red light indicates positive polarity, green indicates negative polarity. Long, 12ft. coil cord and heavy-duty alligator clamp for secure connections. The probe is insulated to prevent the possibility of shorting the side of the probe to other components.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
TOROIDAL COIL TURNS TESTER
TURNS-TTPT
Digital TURNS TESTER for Counting Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity and DC Resistance.Turns Measurement ( through Toroidal Turns Test Platform) : -> TTPT-100 : 5 Turns ~ 1000Turns-> TTPT-1000 : 500 Turns ~ 10,000Turns
-
product
Magnetometer
M-Scan
The M-Scan is a battery powered Locator manufactured in heavy-duty, high-impact ABS with a robust aluminium sensor tube. It has a large, easy-to-read LCD, showing battery level, signal strength and polarity indication backed up with a clear audible response that ensures that the target can be quickly located and identified.
-
product
20kV 4 Collector Test Set
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process.
-
product
Multi-angle Polarized Light Scattering Measurements
LISST-VSF
In-situ measurements of P 11, P12 and P22 elements of scattering Mueller matrix, (P11 is VSF) from 15-150º.VSF (P11) only at small angles, 0.05 to 10º in 32 logarithmic steps in angles.Only two detectors employed with absolute radiant sensitivity (A/W) calibration.Beam attenuation measured with optics similar to our LISST-100X.Roving Eyeball™ optics permit 1-degree resolution in angles between 15 -150º.Sampling rate at 3 seconds per measurement set (involves 3 turns of Roving Eyeball with unpolarized, vertical, and horizontal polarized laser).Daylight rejection by laser modulation.Dynamic range in VSF measurements extended via laser power modulation.Data from small and large angles in a single data stream, including depth and temperature.
-
product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
product
6-48V Auto Tester
1959
Peaceful Thriving Enterprise Co Ltd
*Voltage Display: 6, 12, 24, 48V*LED indicates polarity.
-
product
Cable Tracers
Shanghai Beha Electronics Co., Ltd.
*Trace wires or cables.*Continuity and polarity testing.*Digital Multimeter
-
product
PXI Solid State Switch Module, 3xSPST, 10 A
40-182A-012
The 40-182A-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Multi-Purpose Digital H. V. Phasing Meter
MDP-50K
Standard Electric Works Co., Ltd
● AC 50kV and DC 50kV measurement with direct reading.● 4000-count LCD.● Input impedance : 400 Mohm● Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV DC : 4.000kV / 40.00kV / 50.0kV● MDP-50K must be connected with an approved hot stick, such as HS-175, HS-120.● Polarity indication : Positive / Negative● Backlight function.● Auto power off.● Power source : 1.5V(AA) alkaline battery × 2.● Low battery indication(Multi-level). ● Protection class : IP66
-
product
Digital Display Auto Circuit Tester
1676
Peaceful Thriving Enterprise Co Ltd
This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.
-
product
EOS Tester
KT-200SG
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
product
Antenna, Biconical
EM-6912A | 30 Mhz – 300 MHz
A balun, feedline, and element cage give the Electro-Metrics EM-6912A response curves that are almost linear, making it ideal for swept measurements. An added benefit is that the EM-6912A has an improved BALUN design, which makes it insensitive to changes of orientation while vertically polarized. Readings obtained will be the same no matter which element is closest to the ground plane, eliminating a potential source of measurement error.
-
product
12V Circuit Tester With LED Polarity Indicator
1658
Peaceful Thriving Enterprise Co Ltd
Checks open or short circuits on 12V automotive computer circuits and all primary automotive electrical circuits. Safely tests standard primary automotive circuits and on-board computer controlled electrical system without damaging the micro-processor.
-
product
Universal Multichannel System up to 1.5 kV
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 1.5 kV (A1538D) and 0 ÷ 1/1.3/1.4 kV output voltage (A1515B)- Maximum Current 10 mA, 0.1 or 1/0.1, 3/0.3 mA (dual range boards)- Radiall Multipin, SHV or DB37 connectors- Available with either positive or negative polarity (A1538D and A7038)- Up to 2 nA / 100 pA current set / monitor resolution- Up to 20 mV / 2 mV voltage set / monitor resolution- Very low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A1515B only)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for GEM and Vertex detector and dedicatedaccessories (A1515B boards only)
-
product
System Control Modules for 34980A
The 34980A System and Control modules provide additional measurement and control capabilities that are typically used in test applications. Choose from modules that include digital I/O with programmable polarity, D/A converter with onboard memory to create waveforms, and frequency counter/totalizers.
-
product
Multi Function Automobile Tester
6522
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance, temperature and power providing testing.
-
product
Battery Cell Tester
This Centre zero instruments help to read the voltage irrespective of polarity.
-
product
LC/MS/MS Method Package For D/L Amino Acids
Most important amino acids exist as stereoisomers. D- and L- forms of mirror image isomers, or enantiomers, are named according to their activity on polarized light. By using CROWNPAK CR-I(+) and CR-I(-) columns with chiral stationary phases, the D- and L-forms of amino acids can be analyzed separately. With CR-I(+) elution order is from D- to L-, and with CR-I(-) the elution order is reversed.
-
product
H.V. Probe Meter
PD-40AM
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
