-
Product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
-
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Modbus Register Converter
Model 2390
-
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
-
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
-
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
Single 8x2 1-Pole 16 Amp PXI Power Matrix With Loop-Thru
40-552-012
-
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
-
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
-
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Dial Up Modem Test
ModemTest 1.3
-
Test your dial up modem and telephone line for errors and connection speed. A local loopback test is provided as well as a master / slave test. The master / slave test requires 2 modems and 2 telephone lines. ModemTest is compatible with most dial up modems. (9.6 - 56Kbits)
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
PXI General Purpose 2A Relay Module 19xDPST
40-132-202
-
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
Modbus RTU Analog Input Modules
-
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
Product
PXI 10 x SPST 10 Amp Power Relay Module
40-160-001
-
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
Master-Slave Distributed Motion & I/O Master Controller
PCIe-7856
-
The PCIe-7856 is a PCI Express interface card providing two ports for Motionnet and HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned at the millisecond-level in real time by using a master-slave architecture.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
-
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Digital Input Board
VME-1129
-
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
PXI 18 Channel Power Mux 1 Pole
40-665-001
-
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
Product
8 channel 16 bit Digital to Analog Module
CPCI-DA8-2
-
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
-
Product
EOC Slave
EOS-204W
-
Hangzhou Softel Optic Co., Ltd.
EOS-204W is the EOC slave based on HomePlug AV solution for Ethernet access over coax. It works together with EOC master which is based on HomePlug AV solution as well to construct a two-layer Ethernet data transmission channel on CATV coax cable, provide the Ethernet access service based on the existing coax cable networking. EOS-204W is the slave with 4 Ethernet ports and WIFI.
-
Product
PXI Single 16x4 1-Pole 5A Power Matrix
40-549-001
-
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
NI-9145, 8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis
784756-01
-
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
Product
PXI Single 8x2 1-Pole 10A Power Matrix
40-551-002
-
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
Product
PXI 100 x SPST Ruthenium Reed Relay Switching
40-140A-221
-
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
Smart Protocol Analyzer
-
Works transparently over the Computer's I/O ports (serial & network). The analyzer supports Modbus, Fisher-ROC, BSAP, DNP and other Protocols. In addition to monitoring, this tool is capable of simulating Master and Slave devices.
-
Product
Test Slave For The LIN Bus With Various I/Os
PLIN slave
-
The PLIN slave is an evaluation board with an interface for a LIN 2.0 bus. The device also offers comprehensive I/O functionality, which is accessible via operating and display elements.
-
Product
USB I2C Adapter
MS (Master & Slave)
-
*Plug & Play*No additional driver necessary*HID device drivers are included in major operating systems*Open interface description enables communication without a DLL
-
Product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
-
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
8x4 Power Matrix, 2-Pole, 2xGMCT
40-550-902
-
This version of the 8x4 power matrix is for heavy current/low duty cycle power switching. Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current.
-
Product
Raptor HV High Voltage Tester
-
The Raptor-HV, also called the high voltage slave, is an optional product that extends the Raptor’s applications to tests that require the use of a moderately high AC voltage.
-
Product
MIPI Soundwire Total IP Solutions
Soundwire
-
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
Product
PXI 25 x DPST Electromechanical Relays
40-146-002
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
