-
Product
General Purpose I/O Modules
HY-TTC 30XH
-
The HY-TTC 30XH is a CANopen based, user-friendly and smart Input/Output module that can be utilized as flexible control system extension in mobile applications. HY-TTC 30XH is used in combination with, and controlled by a master electronic control unit, communicating with the slave module via the standardized CANopen® protocol. By mounting the master control unit centrally on the machine and the I/O modules close to the sensors or actuators, a distributed electronic architecture can be implemented in order to reduce mounting time and cost for cabling.
-
Product
MTM-Bus Tester
PXIe-1149.5
-
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
Serial Bus Buffers, Extenders, and Accelerators
-
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
Product
I²C/SPI Interface Device
-
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
PXI CANopen Interface Module
-
The PXI CANopen Interface Module is a high-speed CANopen interface for developing applications with the NI-Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The PXI CANopen Interface Module can transmit/receive PDOs and SDOs according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
Product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
-
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
Product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
-
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
Product
PXI 5A Mux 1-Bank 48-Ch Isolated COM
40-651-011
-
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Handheld Serial Data Analyser
SDA-02
-
Non-intrusively displays, captures and analyses electrical asynchronous data. Directly accepts RS232, RS485/422 and CMOS/TTL signal levels. Modbus over Serial Line protocol capability (RTU & ASCII), automatically checks & generates CRC/LRC, can act as master or slave.
-
Product
PXI 5A Mux 8-Bank 5-Ch Isolated COM
40-651-014
-
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 40A, 14V
40-664A-001
-
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
Dynamic Digital I/O (3U), 32 Ch., Per Pin Control, Up To 100 MHz W/256MB Memory & LVDS
GX5292
-
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch., per Pin Control, up to 100 MHz w/256MB Memory & LVDS
-
Product
Dynamic Digital I/O (3U), 32 Channel, 100 MHz
GX5291-100
-
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch. up to 100 MHz w/128MB On-Board Memory, 32-ch Domain.
-
Product
Dual 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-002
-
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
voltage controlled crystal oscillator
VCXO
-
A VCXO (Voltage Controlled Crystal Oscillator) is a crystal oscillator the output frequency of which is controlled by adding an external control voltage via a frequency control input on a variable capacitance component such as a varactor diode connected in parallel to a load capacitance (CL). Epson VCXOs are divided into two types according to Voltage-Frequency (V-F) characteristic slopes depending on the AFC (Automatic Frequency Control) input configuration of the VCXO. One is a VCXO with a positive V-F slope and the other is a VCXO with a negative V-F slope. Please note that the input voltage of a control circuit will vary according to the individual type, as shown in Figs. 3 and 4. Epson's VCXOs are capable of either, depending on the customer's preference. Epson's VCXOs have been increasingly used for broader applications such as slave oscillators in phased-lock loops, or frequency modulators. Among the above types, a VCXO combined with a TCXO is called a VC-TCXO , respectively. These components have the merit of delicately controlling their output frequency electrically.
-
Product
Manual Oscillators
MOS-01, -01A
-
The MOS-01 manual oscillator module is used as a quality, general-purpose sinewave oscillator and digital readout monitoring system in the MAC-01, -02, or -03 AC Power Sources/Frequency Converters. The unit has guaranteed operating range of 20 HZ to 20 KHZ which is covered in three one-decade scales. The LCD digital metering system is switch-selectable to readout either frequency, voltage or current. A toggle switch selects the input for the attached AC Power Source/Frequency Converter to originate from the manual oscillator itself or from an external laboratory or programmable oscillator source. With oscillator mode switch in Internal position, the BNC connector delivers the signal to drive additional slave units or for oscilloscope sync or monitoring. BNC input/output is completely isolated with 1500 VAC breakdown and excellent common mode rejection. The oscillator modules must be factory installed and calibrated.
-
Product
Wiring Boxes
-
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
-
Product
EBIRST Slave Mode Connection Cable
93-970-301
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
4-CH RTD Thermal Input EtherCAT Module
EPS-3504
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Modbus Master Data Scanner
ModScan
-
ModScan is a Windows application which operates as a modbus master. It allows you to access and change data points in a connected slave device using either the RTU or ASCII Transmission mode. ModScan is ideally suited for quick and easy compliance testing of the modbus protocol and its built-in display of serial traffic allows effective troubleshooting of field connections.
-
Product
XMC Module
XMC-FPD-xxx
-
XMC Bus VITA 42• 3.3V I/O, 5V tolerant businterfaces• Local Bus Clock rates at66MHz• Compliant PCIeSpecification, r1.0a x1• Direct slave data transfers• DMA Capability• Up to 160Mb/s Transfer• DMA Transfer per Fifo Level
-
Product
Open Master/Slave Application Protoco
Modbus TCP
-
Modbus-TCP means that the Modbus protocol is used on top of Ethernet-TCP/IP. Modbus-TCP is an open Industrial Ethernet network which has been specified by the Modbus-IDA User Organization in co-operation with the Internet Engeneering Task Force (IETF) as an RFC Internet standard.
-
Product
PTP Toolbox
OSA 5410/11
-
The OSA 5410 Series is a family of compact and cost-effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network. Following a toolbox approach, the family members of the OSA 5410 Series can be utilized in a variety of network synchronization applications including IEEE 1588v2 Access Grandmaster, Boundary and Slave Clock, GNSS receiver and Primary Reference Time Clock (PRTC), synchronization signal conversion and sync probe applications.
-
Product
PCI Express to VME interface
SIS1100e/3104
-
Single width 6U VME master/system controllerred ball, 1/2/4 GBit/s optical link, red ball, up to 450 m link distance, red ball 128 MBytes memory (PPC Ethernet or VME slave)
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Flow Leak Testing
Leakmaster UltraFlow v3
-
NEW AND IMPROVED EtherNet/IP FEATURING "SLAVE MODE". PROGRAMMABLE ELECTRONIC PRESSURE REGULATOR . DIGITAL MASS FLOW SENSOR WITH BROAD TESTING RANGE . LED STATUS INDICATOR. DUAL ACCESS DOORS FOR FLEXIBLE MOUNTING
-
Product
GPS Wireless Clock
-
Signals & Systems India Private Limited
GPS Clock offers an easy, cost-effective solution for accurate, synchronized time displays without expensive, disruptive installation procedures. Because there are no wiring requirements, installation times are drastically reduced. It is ideal for renovation projects, as there is no need to worry about installation work, as well as new construction. The GPS clock can be synchronized through GPS Antenna or Wireless Antenna. The display can be wall/panel / tabletop mountable. It can be used as a wireless clock to synchronize many wireless slave clocks in and around the buildings.
-
Product
Relay
40-145-101
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
-
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
