-
Product
USB Cable
143555-0R5
-
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
Product
RIBBON 20Pin 0.3M J2 (4 cards)
50-976-020-0.3M
-
Ribbon Expansion Cable for 50-51x series of PCI matrix cards
-
Product
20-Pin GMCT Cable, Female to Female, 16A, 2m
40-970B-020-2m-FF
-
The 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Ferrules, 2m
A003PF4-F-5A200
-
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Ferrules, 0.5m, Spring Latch
A068SMR-F-5B050
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 0.5m, 90º
A1604FT-C-0A050
-
For applications where a 90 degree down cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 8 20-Pin Ribbon Cable Connectors
540160010240
-
Cable Assembly, Receiver, QuadraPaddle, 36", 8 20-Pin Ribbon Cable Connectors
-
Product
Cable Assy 9-Pin D-Type, F/F, 2m
40-970-009-2m-FF
-
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
Cable
RCONQPMC-4
-
RCONQPMC-4 - Transitions from a SCSI-68 pin connector to eight CJ70 Twinax, 3 lug, 1553 cable jack ends and one D-Sub 50 pin connector for additional I/O.
-
Product
Cable Assembly, 104-Pin D-Type, Female to Unterminated, Ferrules, 2A, 1m
40-972-104-1m-FU
-
This 1m long female to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and has unterminated ends with ferrules.
-
Product
Cable Manufacturing
-
For years, we’ve been at the forefront of optimizing and automating how cable manufacturers test their fibers. Whether it’s cable design qualification, in-process testing, or final quality control—PK instruments around the globe are running 24/7 measuring thousands of fibers.
-
Product
USB-to-Serial Cable Converter
-
This cable is the solution for users who want to communicate with GE Multilin IEDs via PCs that have USB communication ports. Using this cable is quick and easy. Simply install the cable driver on your PC, plug in the cable and you are ready to communicate.
-
Product
Cable Fault and Test System Vans
-
Whether you are working on-site, in the countryside or an urban environment, having the right equipment available when conducting fault location operations is vital. When the correct tools can be accessed easily, fault-location time speeds up dramatically, and faults can be dealt with more efficiently. Megger’s range of cable test vans offer solutions to the challenges of fault location in the real world, no matter the environment. Our test van systems have been developed in collaboration with end users to ensure that they live up to the standards of daily fieldwork. Our vans are designed to be adaptable to the end users needs so that the most appropriate tests may be carried out for the cable in question, regardless of whether it is low, medium or high voltage.
-
Product
Cable Connectors & Adaptors
-
After many years supplying high qaulity signal conditioning instruments we understand the need to use high quality cable connectors & adaptors. The connectors used by Kemo on its cable assemblies are fitted by engineers with years of experience. This attention to detail ensures quality signal transmission and minmial noise within the signal path.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 2m, 45º
A1604F5-1604F5-0A200
-
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
Product
Cable Tracing
-
High-power tone generator enables signal detection over 20 miles away and makes tracing through walls and enclosures easier with multiple tones and power levels suited for network, signal wire, coax, and telephone cable applications.
-
Product
Cable and Pipe Locator
PT-14
-
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
Product
VTAC, Patchcord, Receiver, 72", VTAC, DVI-D, to DVI-D Male
7-142706735-072
-
VTAC, Patchcord, Receiver, 72", VTAC, DVI-D, to DVI-D Male.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
-
Product
Inductive Tone and Probe Cable Locator Kit
72-8500
-
This tone & probe set is a basic necessity for anyone running data, voice or any other low voltage cable. It is also suitable for tracing alarm, coax or speaker cables which are already installed.
-
Product
Cable Assy 37-Pin D-Type M/M 2m HV
40-970-037-2m-MM-HV
-
The 37-Pin D-Type High Voltage cable assembly is constructed from PTFE insulated 7/0.2 (24AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 37-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 2m, Exit Away From Pin 1
40-970-050-2m-MF
-
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, .25 Meter
187252-0R25
-
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
Product
Ribbon cable headers
HDRterm50
-
Ribbon cable headers are commonly used with IP compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The HDRterm50 converts from 50 pin ribbon cable to a 50 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
Product
Type X2 double-shielded GPIB cable, 10 m
763061-10
-
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
Product
Cable Testers
E446
-
Tests 3 pin XLR leads, 2 and 3-pole B-gauge jack leads, RCA (phono) leads, most commonly used fuses, and other continuity paths using test leads supplied. Continuity indication by buzzer.
-
Product
Micro Dsub GPIB Cable For PZ2100A (1m)
PX0114A
-
The cable converting MicroD25 GPIB to standard GPIB; compatible with the Keysight PZ2100A
-
Product
Cable Test and Diagnostics
-
Cable testing and diagnostics provides information about the cable’s global condition (e.g. the cable’s overall insulation system), and will reveal localised problems, such as poor joints and terminations; it will also reveal localised weak spots in the insulation. Various cable tests are carried out to spot potential failures before they can cause severe outages. Megger cable test equipment provides access to all of the technology needed to make informed cable management decisions through the different stages of the cable’s life cycle.
-
Product
Cable Assembly, Receiver, 36", Mini Coax, 6 SMB Plugs
540093010207
-
Cable Assembly, Receiver, 36", Mini Coax, 6 SMB Plugs.
