PCB
See Also: Printed Circuit Board, PCBA, Crosstalk
-
Product
Pre-Bonded Metalbacked PCB
-
Teledyne Labtech's significant in-house resources have the capability to satisfy the most exacting demands of complex pre-bonded PTFE Microwave PCB. Our extensive machine shop facilities allows Teledyne Labtech to offer a complete sourcing solution from low volume prototypes to high volume production requirements. Teledyne Labtech can also offer pre-bonded metalbacked PCB with integrated wave-guide transitions and co-planar wave-guides.
-
Product
Test Handler
JOT M5
-
Simple, cost-effective way to automate PCB and pallet based testingSafe, reliable product handlingQuick-adjust ease: no product-specific partsFaster handling of smart productsIndustry 4.0 autonomous interconnectivityTruly scalable for growing test needsReusable, application-specific test boxesM-TestBoxes compatible with M1 handlerBoxes are fully independent, just pull out from M5 rack and use in off-line testingFail product separation to integrated magazineSpacious service-friendly constructionErgonomic workspaceTouchscreen UI with base statistics and service capabilityEasy start-stop operabilityAutomated width adjustment
-
Product
25-Pin D-Type Female Straight PCB Mount
40-963-025-SF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Digital Incircuit Test
PFL780/760
-
The PFL780 and 760 use IC clips as a test interface. This makes them ideal for the service and maintenance of legacy systems. If you need to work on high density surface mount PCBs you should consider the GRS500 as a more suitable alternative.
-
Product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
-
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
Riser
RISER-SUMIT-2
-
WINSYSTEMS’ RISER-SUMIT-2 boards are designed to provide extra space in a SUMIT stack. They are printed circuit boards (PCBs) with SUMIT mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
Combination Board Testers
QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities for conventional PCBs.
-
Product
Fault ID & Repair
-
As a manufacturer of bare PCBs, you know that your reputation sits right on top of every board you send out. You have to get them right, but with every PCB you discard, you’re throwing away precious labor, materials, power and time, along with many other costly elements that go to make up your products. That’s why it’s important to know which of your flagged boards are in fact electrically sound, and whether repair is a viable, reliable option.
-
Product
8 Pin Power D-Type Male Connector, 40A, PCB Mount
40-963-008-RM
-
This connector is suitable for Pickering Interface's modules that use the 8-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
3D Solder Paste Inspection
aSPIre 3
-
Industry-leading measurement accuracy and inspection reliability- Perfect solution to eliminate shadow problems, base plane settings, and problems with projection direction- Full 3D foreign material inspection solution for the entire PCB- High productivity through the highest accuracy
-
Product
Exchangeable Test Fixture
MA 2109/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
Product
Header/Shroud Right Angle Kit, ITA, QuadraPaddle, For Custom PCB Mounting (requires 510 151 107)
510109316
-
Header/Shroud Right Angle Kit, ITA, QuadraPaddle, for Custom PCB Mounting (requires 510 151 107)
-
Product
Strain Sensors
-
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
Product
SMT/BGA Rework Station
PDR IR-C3 Chipmate
-
The PDR IR-C3 Chipmate entry level SMT/BGA rework system is specifically designed to be lower cost but still cope with the challenges of repairing today's small, medium sized PCB assemblies.
-
Product
160-Pin DIN41612 Connector, Straight PCB Mount, Male
C1604MX-XPS-0A
-
Accessory allows a user to create their own PCB based termination solution. This connector is not suitable for directly mounting onto a Pickering switching or cabling product.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type E, Ø1.50mm, 305gf
K100-E150305-SKAU
-
K100 Series, Pitch 100mil, Tip Style E, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 96 Pin SCSI Plug
510109485
-
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 96 Pin SCSI Plug
-
Product
9-Pin D-Type, Male, Straight PCB Mount
40-963-009-SM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Engine Control
StepGenerator4
-
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
Product
FR-4 PCBs
-
Monthy Capability: 1200 Sq M/MonthLayer: 4 LayersMaterial: FR4 TG140Dimension: 335.14mm*245.65mmFinished board thickness: 1.6mm+/-0.13mmFinished copper thickness: 2ozMin Trace Width/Space: 8/8milMin hole size: 0.3mmMin hole wall copper: ≥25UMSoldermask Color: YellowSurface finishing: HALApplication field: Consumer electronics
-
Product
ABex Terminal Module for Göpel 1149Cx-FXT BSCAN Cards
ABex TM-1149Cx-FXT
-
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
-
Product
90 Degree Hybrid Couplers To 600 MHz
-
This category of hybrid dividers features designs from 5 to 600 MHz with 2:1 to 4:1 bandwidth. Maximum insertion loss of 0.5 dB is specified for most units. These 90-degree hybrids are designed for a power rating of 1 watt maximum for a load VSWR of 1.2:1 or better. For use in 50-ohm environments.Pulsar Microwave currently offers this product line in three space-saving packages. The connectorized outline 412 comes standard with SMA female connectors. Outline C is a surface mount package useful for handheld applications with limited PCB area. Outline 301 is hermetically sealed for rugged environments.
-
Product
Advanced Diagnostics for ScanExpress™ JET JTAG Embedded Test Solutions
ScanExpress JET Advanced Solutions
-
ScanExpress JET advanced diagnostics add additional diagnostic resolution with fully automated analysis translating functional test results to down to the net and pin level, even with BGA packages.The seamless integration with ScanExpress JET and ScanExpress Runner as well as the ability to output ScanExpress Viewer fault reports for PCB visualization make ScanExpress JET Advanced Diagnostics a must-have tool for any JTAG test system.
-
Product
3.5 Inch SBC with 7th Gen Core i7 CPU and PCIe/104
VENUS
-
Based on the “Kaby Lake” 7th generation Core i7 processor, Venus offers high CPU performance in a small form factor rugged SBC with modest power consumption. It incorporates a full suite of rugged features such as soldered memory, latching connectors, a thicker PCB, and true -40/+85ºC operating temperature, making it suitable for the most demanding vehicle applications. High I/O density, multiple expansion sockets, rugged design, modest power consumption of 14W, and wide temperature operation combine to make Venus an extremely attractive option for applications requiring high CPU performance or ruggedness.
-
Product
SIM, Module, ITA, 90 Series, Fully Loaded with pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106)
510171102
-
This fully loaded SIM module kit comes with 34 pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106). This kit also includes two PCB brackets for securing module to PCB.
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
PCB Adapter, Receiver, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort
510170116
-
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single DisplayPort connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
Product
Manual Drive Unit
ATE MA350
-
Parallel contact stroke: 20 mm. Contact force max.: 300 N. Component on PCB: 58 mm. Pressure frame unit-opening angle: 66.Weight: 2,60 kg
