PCB
See Also: Printed Circuit Board, PCBA, Crosstalk
-
Product
PCB Adapter, Receiver, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510170114
PCB Adapter
Mates with p/n 510171114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
Product
Printed Circuit Board
RISER-PPM-1
Printed Circuit Board
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
PCB Adapter, ITA, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510108140
PCB Adapter
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
Product
High Temperature
-
PCB® offers specially designed and tested ICP® and charge mode accelerometers for testing in extremely high temperatures.
-
Product
MPI PCB Probe Systems
-
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
DUT Boards
-
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
Product
Diagnostic Cores
VersaCore™
-
The diagnostic cores are uniquely designed in the VC20 format. Using the customizable PCB, components can be added to create a "golden core" to quickly troubleshoot your system Test SMUs, Test Motherboard, Test Pogo pins, Test Relay matrix.
-
Product
8GB SO-DDR5-5600 1GX16 1.1V SAM
AQD-SD5V8GN56-SC
Memory Module
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
-
Product
Process Improvement
-
Omron’s numerous software solutions for quality control, process improvement, defect monitoring and more are ideal for PCB manufacturers seeking to boost productivity.
-
Product
Fineliner
-
The parallel tester Fineliner enables two-sided contact with fne structures. Withvisual detection of both substrate sides and corresponding adapter position correction≥ 300μm test points can be contacted. The rigid needle adapter with a pitch of ≥ 400μmalso allows a high contact density. This results in a large test depth on the substrate.The integrated DMC reader ensures a correct test result assignment. Multiple PCB canbe tested step by step through in the X-direction of the Fineliner, further eliminatingsubstrate tolerances in the X-direction, and enabling more cost-effective adapters andmeasurement techniques. A quick-release system with identifable replacement kitsensures safe and quick retooling.The measuring technology can be defned customer-specifcally. There are 2040 pyloninterface points per side.
-
Product
Press-fit-Tooling
-
The electronics industry is increasingly using Press-fit applications. Through-hole components are increasingly being converted to press-fit solutions. A press is used to push the press-fit connectors into a PCB. This is done in our ESD-safe room. The customised press-fit tooling is used in this process to support the work. The tooling is made of aluminium, brass, stainless steel and ESD-safe composite materials.
-
Product
SSMA Connectors
-
Pasternack SSMA connector category includes 52 part numbers, most are RoHS and REACH compliant. SSMA connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack SSMA connectors are built to precise microwave and RF industry specifications. Connectors in SSMA series are manufactured in male or female gender with 50 Ohm impedance. SSMA connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SSMA connector designs include crimp/solder, solder, solder (without contact) or solder/solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SSMA connector series is in-stock. Not just in stock, but these connectors will ship the same day as they are purchased.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg
-
Product
Linear Testfixture (Cassette Not Included), UTT 456 x 320 mm
MG-07
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 590 x 100 x 184 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
CAT-5 Video Drivers
-
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 305gf
K100-H080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
07R THT Vertical | Non-Threaded | With Shaft
07R3-xx-00
-
Miniatur selector with shaft, PCB mounting and up to 3.5 Ncm switching torque
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 155gf
K100-G150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
Large Format PCB
-
Teledyne Labtech is one of the few companies in the world who can offer large format PCB for use in RF/Microwave applications. Our continued investment has expanded our capabilities to enable Teledyne Labtech to offer a large range of non-standard PCB. Our auto-clave vacuum oven capability allows Teledyne Labtech to manufacture large format Multilayer PCB.
-
Product
Universal SOIC-to-0.600 [15.24] DIP Adaptor
Series 647
-
Universal SOIC to .600 [15.24] DIP Adapter. 44 pin adapter for mounting Aries Series 547 Universal SOIC ZIF (zero insertion force) Test Socket to .600 [15.24] DIP PCB layout. Consult Data Sheet No. 10015 for test socket information.
-
Product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
PCB Adapter
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
Product
Automated Soxhlet Extractor
Soxtec™ 8000
-
The Soxtec 8000 extraction unit is a fully automated system for fast and safe extraction of soluble matter from a wide range of matrices. It performs the four extraction steps boiling, rinsing, solvent recovery and auto-shut down, fully unattended. Just load, start and walk away. The Soxtec 8000 is specially designed to ensure the highest possible throughput and safety.Parameters: Crude fat, Total fat and Extractable matterSample types: Fat in food and feed. Extractable matter in textile, paper pulp, plastics, rubber etc. PCB and PAH in soil and sludge (the Soxtec is a preparatory step to GC-MS).
-
Product
25-Pin D-Type Female Straight PCB Mount
40-963-025-SF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
RF Connectors
HD-EFI Connectors
-
The HD-EFI product series is a micro-miniature interface designed to allow large board tolerance stack ups, blind mating, and multiple RF lines. It is available in common PCB jack and cable plug configurations, with an assortment of bullet adapters to accommodate many board to board spacing options.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 155gf
K100-L150155-SKAU
-
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
500-Pin SEARAY Connector, Male Without Backshell, 1 Amp, 500 Port
C500RMX-4SB-0A
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Optical Inspection
-
Typically, in a standard PCB manufacturing facility, there will be a department where people perform inspection of PCBs through a manual processes, such as visual inspection with magnifiers, microscopes, etc...
