Control
Known value
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Type X2 double-shielded GPIB cable, 16 m
763061-16
-
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
Product
Packet Analysis Probe for PCI Express
N4220A/B
-
When purchased with a logic analyzer, the application software you order is installed on the instrument hard drive. If you need to add application support after your initial logic analyzer purchase or are controlling a logic analyzer from a host PC, you must install the appropriate software before you can make measurements.
-
Product
Battery Voltage Supervisor
BVS
-
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
Product
SparkFun Dev Board
AST-CAN485
-
The SparkFun AST-CAN485 Dev Board is a miniature Arduino in the compact form factor of the Pro Mini. In addition to all the usual features that a mini Arduino has, it possesses an onboard CAN (Control Area Network) and RS485 ports, enabling quick and easy interfacing to a multitude of industrial devices. The CAN485 Dev Board bridges the gap between the maker and industrial spaces!
-
Product
Power Quality
-
Schweitzer Engineering Laboratories, Inc.
SEL power quality controls increase power efficiency and reliability by improving a system’s power factor and voltage stability.
-
Product
High-Voltage Test Device
PGK 70 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
NI-9227, 50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module
781099-01
-
50 kS/s/ch, 5 Arms, 24-Bit, 4-Channel C Series Current Input Module - The NI‑9227 was designed to provide high-accuracy measurements to meet the demands of data acquisition and control applications. It includes built-in anti-aliasing filters. When used with a C Series Voltage Input Module, the NI‑9227 can measure power and energy consumption for applications such as appliance and electronic device test. You can not only measure and meter current and power but also look at quality factors such as noise, frequency, and harmonics.
-
Product
Temperature and Humidity
-
Is a complete line of high performance diagnostic tools designed for HVAC/R, electrical, industrial maintenance, automotive as well as quality control and fire prevention applications.
-
Product
100 amu CIS Analyzer
CIS100
-
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
Product
Shaft Power Measurement Solutions
-
Our marine shaft power meter systems measure shaft torque, power, propulsion, rpm and thrust (if required), to ensure optimum performance is maintained throughout the lifecycle of a vessel. Using highly accurate & reliable strain gauge technology, combined with cutting-edge electronics, our system has an accuracy of 0.1%. It can be installed and commissioned within 1-2 days on a variety of shafts including intermediate shafts, thrusters, propellers and controllable pitch propellers. Our technology, along with our expertise in dynamic sampling of strain gauges, enable us to unlock a significant amount of information regarding the performance of the engine & propulsion shaft, along with the propeller.
-
Product
Digital Control Step Attenuator
-
Digital control attenuators with TTL parallel control offering fast switching speed and high attenuation accuracy
-
Product
IQ Vector Modulators
-
PMI offers a various I/Q Vector Modulators having analog control or digital controls and we can design models that meet your specific needs. We can offer up to 40 GHz operating frequencies.
-
Product
Switches-Limiter
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
Product
Fixed Area Hydrogen Monitor
HY-ALERTA™ 600B
-
H2scan’s HY-ALERTA™ 600B Fixed Area Hydrogen Monitor will provide hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. They are designed for either ceiling or wall mount and have RS422 capability that extends the interface from the sensor to the controller to several hundred feet. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to any other combustible gases, thus eliminating false positive alarms and increasing system reliability.
-
Product
Chamber Controller Software
-
EDC (Embedded Device Control) is specifically designed software for Sentek chamber system controllers running Temperature and Humidity environmental tests. The EDC software features an intuitive interface, a powerful data review function and live data viewing.
-
Product
Switching Unit
ZET 454
-
The ZET 454 switching unit is intended for serial switching of 72 circuits of ZET 452 control devices to one of the sixteen sockets. The ZET 452 electric circuits control device is connected to a socket on the ZET 454 switching unit front panel. On the front panel of ZET 454 there also are sockets for tested device circuits connection, which is performed using the adapter harnesses.
-
Product
Edge Connector Fixture
220EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
Signal Generator, 20MHz, 2 Channel, Arb.
33512B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
Parrafin Oven
UNpa
-
The universally applicable oven is our classic appliance for temperature control in science, research and material tests in industry. The technologically perfected masterpiece made of high-quality, hygienic, easy-to-clean stainless steel leaves nothing to be desired in terms of ventilation and control technology, overtemperature protection and precisely tuned heating technology.
-
Product
Polyalphaolefin Liquid Chillers
PAO
-
PAO, a fluid that does not react with water and is compatible with most metals, is the basis of the Bemco PAO-II series of fluid conditioners. Similar to the Bemco PCL Chillers, PAO-II Liquid Chillers are furnished as free standing caster mounted systems, ready to provide a reliable and precisely controlled flow of temperature conditioned PAO fluid. These systems are optimized for use with Polyalphaolefin fluid in an Aerospace environment.
-
Product
Altitude Test Chamber
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Morningtest altitude test chamber combines temperature and altitude environments with optional humidity for simultaneous environmental testing. An altitude chamber allows users to control the environmental test chamber temperature while subjecting the product under test to various levels of altitude up to 150,000 feet.
-
Product
Diagnostics & Testing Equipment
-
Parker offers an array of diagnostic and test solutions for measuring hydraulic and pneumatic data and for troubleshooting operational problems. These include analog and digital flow and pressure meters and viscometers as well as associated devices such as sensors, vacuum and pressure controllers, quick couplings, and test point connectors.
-
Product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
-
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
-
Product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
-
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions. .The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
Double Regulation Power Supply
-
Double regulation power supplies include: DO series, AxN series, ATR series.The Power Supplies of the AxN series are built with the double regulation technique. The first regulation is obtained by the partialization of the grid circulation angle as automatic variac. The second regulation functions as a linear stabilizer with constant dissipated power. As a result, this solution allows to obtain both low power dissipation and, thanks to the linear regulation, excellent output characteristics.DO series Power Supplies are made with the double regulation technique. A linear stabilization circuit is added to a thyristor-controlled bridge, which allows to reduce the power absorbed by the network. This type of control allows a volume reduction compared to linear power supplies but it preserves the characteristics of low noise and speed of response.ATR linear Power Supplies series are built with the double regulation technique. the first regulation is obtained by the personalization of the grid circulation angle as automatic variac. The second regulation functions as a linear stabilizer with constant dissipated power. As a result, this solutions allows to obtain both low power dissipation and, thanks to the linear regulation, excellent output characteristics.
-
Product
Precisive® 5 Application Specific Gas Analyzers
-
The Precisive® Gas Analyzer is a real-time gas analyzer based on MKS' unique Tunable Filter Spectroscopy (TFS™) platform. The Precisive suite of products are calibrated for the measurement of a wide range of gases across multiple process industries. The real-time, continuous measurement capability provides immediate analysis ensuring control of critical process parameters.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 5.82M
40-297-152
-
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Intelligent Refrigerant Extraction Tester
DET-10M
-
Shanghai Dean Electrical Co., Ltd
The instrument adopts numerical control temperature control and signal acquisition system;The autoclave is made of integral stainless steel 316#, without welding seam, and can withstand high temperature and high pressure up to 50MPa;Automatic temperature, pressure, time and cycle times Control, real-time display of parameters;Four-way safety protection;Used to test the refrigerant resistance of enameled wires in refrigeration systems.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
