-
Product
Fault Level Monitoring
-
The fault level or fault current is the maximum current to flow on a network in the event of a fault.
-
Product
Remote Plasma Source
MAXstream
-
Advanced Energy’s MAXstreamTM line is the next generation of remote plasma sources for chamber cleaning. The MAXstream is available in 3, 6, 8, 10, and 12 SLPM NF3 flow rates to optimize price and performance.
-
Product
Bidirectional AC Source / Sink With Regenerative Power Supply
EAC-4Q-GS
-
Single system from 30kVA to 500kVA and in parallel up to 2MVA and more. Galvanic isolation from the network. TFT touch display with simple menu navigation. Emergency stop in the front door. Indicator lights for operating status. Bidirectional current flow, up to 100% of the nominal output power can be fed back into the grid. Output voltage and phase angle adjustable per phase.
-
Product
8-CH Analog Input Module
ND-6017
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Hazardous Location Syringe Pump
500HLf
-
The Teledyne LABS HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
Product
Portable Hydraulic Testers
-
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
Product
Rotor-X Paddlewheel Flow Sensor
515
-
The Signet Model 515 sensors are offered in a variety of materials for a wide range of pipe sizes and insertion configurations. The many material choices, including PP and PVDF, make this model highly versatile and chemically-compatible to many liquid process solutions. Sensors can be installed in up to DN900 (36 in.) pipes using Signet's comprehensive line of custom fittings. These custom fittings, which include tees, saddles, and weldolets, set the sensor to the proper insertion depth into the process flow. The sensors are also offered in configurations for wet-tap requirements.
-
Product
Hydraulic Data Acquisition System
C2000
-
Measure hydraulic flow, pressure, temperature, speed, current (Amps), contamination and other custom inputs.
-
Product
LilyPad Light Sensor
-
The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs voltage between 0V and 3.3V depending on the level of ambient light shining on it. As more light is applied on the sensor, more current will flow from the board through the signal tab to the microcontroller you connect the sensor to. If the sensor receives no light, no current will flow through it. In a typical indoor lighting situation, the sensor will output around 1 to 2V. Adding this board into your next e-textile or wearable project will really open up the possibilities by being able to incorporate light level sensing capabilities.
-
Product
Vapor Source Mass Flow Controller With Viscous Choked Flow
-
The 1150C Vapor Source Mass Flow Controllers are pressure based measurement and control systems designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas using viscous flow through a choked orifice.
-
Product
SparkFun Thermocouple Breakout
MAX31855K
-
The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that makes reading a wide range of temperatures possible. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a 'hot' end and a 'cold' one). Once this is achieved, a voltage potential is formed and current flows. The SparkFun Thermocouple Breakout takes a standard Type-K thermocouple in one end, digitizes the temperature measured and sends that data out the other end via a SPI interface, thereby interpreting the data and translating it for you to read!
-
Product
Positive Displacement Pumps
-
Flowserve positive displacement pumps comply either with ASME or API standards. They cover screw and reciprocating pumps in different configurations that guarantee reliable and efficient pumping processes. Numerous sizes, hydraulics and material combinations are particularly well suited for use in applications where uncompromising reliability and efficiency over a wide flow range are key.
-
Product
Variable Constant Differential Flow Controller
VCD 1000
-
The Porter Model VCD 1000 flow controller is precision-engineered to control low gas flows at constant mass flow rates regardless of changes in downstream pressure.
-
Product
Flow and Pressure Meters
477
-
Parker Conflow’s Code 477 is an in-line flowmeter that provides both flow and pressure measurement functions in one compact unit, allowing a diagnostic check on ITP systems on coal cutting machines.
-
Product
Leakage Current Alarm Signaler
MPU-1
-
MPU-1 is dedicated to control (measure) leakage current in AC, low and medium voltage power networks. It is designed to make measurements, which results define network's safety condition for leakage current. The device enables to set limit for maximum safe value of flowing leakage current and for values above this limit visual and sound alarm is activated.
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Flow Cell Kit
QCMT
-
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
-
Product
Masks Bacterial Filtration Efficiency Tester
-
Sataton Instruments Technology CO., Ltd
Face Masks bacterial filtration efficiency BFE tester is to determine the bacterial filtration efficiency (BFE) of medical face mask materials by employing a ratio of the upstream bacterial challenge to downstream residual concentration of the tested medical face mask materials. The tester provides certain flow rate of bacterial aerosol. The operator can measure the number of colony forming units passing through the medical face mask material, which is clamped between a six-stage Anderson cascade impactor and an aerosol chamber, expressed as a percentage of the number of colony forming units present in the challenge aerosol.
-
Product
MFP-570 Main Fuel Pump
-
The MFP-570 provides main engine burn flow as well as servo flow and engine actuator flow. This two-stage “cartridge type” fuel pump is designed to be inserted directly into the engine fuel metering unit.
-
Product
Air Core Shunt Reactors
-
Shunt Reactors act as absorbers of reactive power to increase energy efficiency of the power system. Shunt Reactors are inductors that are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. The shunt reactors provide inductive compensation.
-
Product
Temperature & Environment Monitors
Room Alert
-
Monitors Temperature, Humidity, Power, Flood/Water, Smoke/Fire, Motion, Room Entry, Air Flow, Panic Buttons, Network Cameras and more. Offers built-in sensors & allows external sensors to be added.Allows unlimited alert notifications & unlimited users. Allows notification via email, SMS, SMTP, dial-out page, audio alert, webpage update, logfile update and more.
-
Product
Multiphysics Computational Fluid Dynamics (CFD) Simulation & Analysis
STAR-CCM+
-
Siemens Digital Industries Software
STAR-CCM+ is a stand-alone simulation solution for computational fluid dynamics (CFD), computational solid mechanics (CSM), heat transfer, particle dynamics, reacting flow, electrochemistry, electromagnetics, acoustics and rheology. STAR-CCM+ delivers accurate and efficient simulation technologies through a single integrated user interface and automated workflows. This facilitates the analysis and exploration of complex real-world problems.
-
Product
Anemometer
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Digital Wind Speed Air Flow anemometer Temperature Meter Tester
-
Product
Calibrated Leak Standards
-
LeakMaster is a leader in the industry when it comes to the manufacturing of calibrated leak standards (calibrated leak orifices). Each leak standard is meticulously manufactured to a specific leak or flow rate at a predetermined pressure. The purpose of each leak standard is to teach, or calibrate a leak test program, and allow the leak test instrument to memorize the characteristics of a leaking part. These leaks are also introduced into production parts to simulate a “leaking or failed” part condition. LeakMaster supplies a calibrated leak standard with every leak test instrument, and provides recertification services for all of their leak standards
-
Product
Flow Meters
-
Omega's flow technology portfolio includes variable area, positive displacement, electromagnetic, mass flow, turbine, doppler and transit time ultrasonic, paddlewheel, vortex, and coriolis.
-
Product
Stand-alone Ozone Delivery System For Advanced Processes
SEMOZON® AX8585
-
SEMOZON® AX8585 stand-alone ozone gas delivery system is designed around the AX8410 PRIME ozone generator to provide high flow, high concentration, ultra clean ozone generation and delivery. This fully configurable product line is designed to meet the ever changing needs of the semiconductor industry. Each SEMOZON AX8585 is a fully integrated, high output ozone gas delivery system intended for use in an increasing number of semiconductor process applications such as ALD, CVD, TEOS/Ozone CVD, photoresist strip, wafer cleaning, contaminant removal, and oxide growth.
-
Product
Peristaltic Pumps
PeriXus
-
Teledyne LABS PeriXus® peristaltic pumps was developed with your lab or manufacturing plant in mind. With its compact and modular design, this space-saving pump uses peristaltic technology to help reduce the possibility of contamination, making it a great pump to use when handling volatile materials.The ability to quickly change hoses allows you to switch from pumping one material to another in minutes, maximizing application flexibility. The available hose options are designed to handle even the toughest materials, including highly viscous fluids. With a flow rate of 0.005 to 162 mL/min, this peristaltic pump is ideal for a variety of markets, including pharmaceutical/biotechnology, research and development, petrochemical, and reaction chemistry.
-
Product
Rotor-X Paddlewheel Flow Sensor
2536
-
The Signet 2536 Rotor-X Paddlewheel Flow Sensors are offered in a variety of materials for a wide range of pipe sizes and insertion configurations. The many material choices, including PP and PVDF, make this model highly versatile and chemically-compatible with many liquid process solutions. Sensors can be installed in DN15 to DN900 ( to 36 in.) pipes using Signet's comprehensive line of custom fittings. These custom fittings, which include tees, saddles, and weldolets, seat the sensor to the proper insertion depth into the process flow. The sensors are also offered in configurations for wet-tap installation requirements.
-
Product
Ultrasonic & Mass Flow Meters
-
GAOTek offers high quality, affordable, secure and accurate Ultrasonic Flow Meters for sale to the United States, Canada and globally. Ultrasonic Flow Meters often have a sending and a receiving transducer for measuring the velocity of fluids to accurately calculate the flow of volume in a pipe by using sound waves, acoustic waves or vibrations with a frequency of >20 KHz. GAOTek offers a variety of top-notch Ultrasonic Flow Meters designed for different environments, from wide pipes to an all liquid environment, such as sea water, oil, sewage, alcohol, et al. GAOTek’s easy to use Ultrasonic Flow Meters come with a built-in printer and a built-in data logger. They provide accurate readings and have an accuracy rate of ±1% at rates greater than 0.2mps. They also offer multi-language menu selections, long lasting battery life for continuous usage, large LCD screens, and a huge storage.
-
Product
Reciprocating Pumps
ReaXus
-
Teledyne LABS ReaXus® reciprocating pumps covers a broad range of application needs, ranging from 5 mL/min to 300 mL/min and up to 6,000 psi. Whether you need low pulsation or are working with hazardous materials, the ReaXus line has an option for you. The single piston models are targeted towards moving material or providing pressure. The dual piston models are focused on continuous processing applications where a steady flow of material is important.The ReaXus product line is low maintenance and requires no calibration like other styles of pumps, saving your organization time and money.
