Surface Resistance
-
product
Earth Contact Resistance Tester
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
product
Transformer Winding Resistance Meter
10A
*10A DC continuous current in 4 ranges of 0.01A, 0.1A, 1A and 10A.*4 ½ digit display for higher resolution.*Dual channel measurement.*Suitable for operation in energized switchyard conditions.*Specialized protection circuits for suppression of inductive voltage kickback.*SMPS based - lightweight and portable.
-
product
Earth Resistance Testers
Is a soil resistance measuring instrument. It is used for sizing and projecting grounding grids.
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Battery Resistance Tester
BT-3915
Kongter Test & Measurement Co., Limited
Regular test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106. The excellent performance of BT-3915 for testing battery internal resistance and voltage will help you pick out the weak batteries and ensure their performance in short time measurement.
-
-
product
Resister
Our ARFC type Film Flat Chip Resistor & ARFCN type Thin Film Chip Resistor Network are high precision Metal Film resistors produced with high purity. Alumina Substrate and Ni-Cr-Si Resistor Film based on high precision Etching Technology. The electrode Terminals are made with Spattering Film and Nickel-Solder Plating, and solderability is very good in all Flow, Reflow and Dipping type soldering for Hybrid IC, SMT, PCB etc. Our ARFC Metal Film Resistor & ARFCN type Thin Film Chip Resistor are being produced under the thorough quality control, and are being used widely in high precision and high reliability electronics circuit such as Measuring Instrument, Medical Instruments, Communication and other Industrial Instruments.
-
product
Ground Network Earth Resistance Tester
HTDW-5A / 736
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for the test of grounding resistance of large power grid in power departments, substations and other institutions.
-
product
Resistance Calibration
Process Instruments maintains fractional part-per-million accuracy with a state of the art resistance calibration facility. Specialized services include precision resistor manufacture, resistor and shunt repair, characterization of alpha and beta temperature coefficients and the determination of barometric effects on resistance values.
-
product
Anti-Surge Chip Resistors (Double-Sided Resistive)
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
product
Low Resistance Or Continuity Testing
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
product
High-precision Surface Inspection for Wind Turbine Blades
waveCHECK™
8tree's waveCHECK is a handheld-portable 3D-inspection tool for inspecting wind turbine blades in manufacturing and operation. Its efficient detection of surface defects and instant visual feedback revolutionize surface inspection.It can detect wrinkles, steps, gaps, rain erosion and any other surface damage.
-
product
SURFACE PROFILE GAGES
Steel is often abrasive blast cleaned or otherwise roughened prior to painting. The peak-to-valley height of the resultant surface profile is an important factor in the performance of applied protective coatings. Low profile may reduce coating bond strength (adhesion). Too high and the peaks may receive insufficient coverage and possibly rust prematurely. The costly application of more coating may be required if the profile is too high. For these reasons, surface profile should be measured prior to coating application to ensure that it meets contract specifications.
-
product
4 2/3 Digital Resistance Meter
CS2-RS
CS2-RS Resistance Indicator has been designed with high accuracy measurement, display and communication of Ohm (2 wire) as like as Coil of motor or transformer.The meter supports Field Calibration function. It can be calibrated with sensor (Resistance) to meet machinery structure.We build flexible function as like as 3 bank (for multi-range scaling and set point) and 3 external control inputs meet to various testing equipment inquiry.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments applications.
-
product
Surface Defect Inspection System
Wafer for inspection of surface condition of specular flat substrate, glass substrate, others φ 100 ~ φ 300 compatible
-
product
DUT Resistance Tester
AllWin Instrument Science and Technology Co., Ltd.
1. This test verfies the integrity of DUT2. The resistance is measured by measuring voltage3. Current is made by distribution
-
product
Surface Form Analysis System
Tropel® FlatMaster®
Tropel® FlatMaster® Surface Form Analysis System Fast and Precise Measurements of Ground, Lapped, Honed, Polished and Super-finished Components. The Tropel® FlatMaster® offers industry leading performance for surface form measurements to precision component manufacturers. Our non-contact optical technique analyzes the entire surface of the part in seconds, regardless of its size or complexity. The FlatMaster provides five nanometer resolution and a standard accuracy of 50 nm (2.0 μ). It rapidly and accurately measures flatness, line profile, radius and other surface parameters on a variety of materials and surface finishes.
-
product
Battery Internal Resistance Tester
HTBNZ-V / 290
Wuhan Huatian Electric Power Automation Co., Ltd.
Using advanced AC discharge test method, can accurately measure the battery voltage and internal resistance.
-
product
Insulation Resistance Measurement
MI20KVe
The MI-20KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV.
-
product
Ground Resistance
Provide accurate and reliable measurements of both ground resistance and soil resistivity for installation and troubleshooting.
-
product
Resistivity Meter
Model 2180
The unit is compact and lightweight. The basic system is 7″ wide by 2.5″ high and 12″ long. When measurements are needed below approximately 100 micro-ohm-centimeters, the basic system is piggybacked onto a second enclosure that houses a power amplifier with a current gain of ten. The combined unit measures 7″ wide by 5″ high and 12″ long. The combined unit weighs 11.5 pounds. Two short cables interconnect the two enclosures for powering the power amplifier and routing the signals to the fixture or four point probe. The front panel of the basic system includes a 32-character backlit LCD display and a set of function keys. An easy-to-use menu will allow access to user defined parameters such as sample thickness, sample volume, and calibration constants; upper and lower alarm limits, relative measurements, and several others.
-
product
Moisture Resistance/ Humidity Test
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
product
Surface Mount Switches
Dow-Key® Microwave offers PCB mounted, miniature electro-mechanical microwave switches. These switches are designed with an overall size of 0.75” x 0.75” x 0.58” and weight of 0.5 ounces for test and aerospace applications where small size, reduced weight, and less power consumption are critical.
-
product
Insulation Resistance Tester
BC2010 / 751
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for measuring cable, motor, generator, transformer, transformer, high voltage switch, lightning arrester and so on.
-
product
Surface Roughness Testers
Widely used in production site to measure surface roughness of various machinery-processed parts, calculate corresponding parameters according to selected measuring conditions and clearly display all measurement parameters.
-
product
3D Optical Surface Profiler
NewView™ 9000
The NewView™ 9000 3D optical surface profiler provides powerful versatility in non-contact optical surface profiling. With the system, it is easy and fast to measure a wide range of surface types, including smooth, rough, flat, sloped, and stepped. All measurements are nondestructive, fast, and require no sample preparation.
-
product
High Resistance Neutral Grounding Devices
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
product
Ground Resistance Tester
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
product
Hand-Held Surface Probe
HP 1000-SP
Advanced Thermal Solutions, Inc.
The HP 1000-SP is a stainless steel, single-sensor hand-held probe designed for measuring the surface temperature of solids. Its pointed tip allows for exact positioning of the sensor on the desired spot. This enhances measurement accuracy by eliminating any conduction heat transfer that may occur through the stem.
-
product
Large Range Resistivity Tester
HS-SFRT
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
