Filter Results By:
Products
Applications
Manufacturers
-
product
Piezo Velocity Sensor
VE102
Piezo Velocity Sensor, Side Exit Connector / Cable, 100 mV/in/sec
-
product
Precision Positioning stage
N-661
Physik Instrumente GmbH & Co. KG
Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Single Channel High Voltage Linear Amplifier
F10A
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Wrist Strap Monitors
Single conductor (more commonly called single wire) ESD wrist strap monitors detect capacitance. These simplified monitors sense the input connection but do not discern precision resistance. They also offer additional value by monitoring the worksurface (ESD Mat) and the ground connection. The built-in LED offers local visual alerts, and a small piezo buzzer offers a nice clear audible alert to the operator at the bench.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Scanning Electrochemical Systems
The VersaSCAN is a single platform capable of providing spatial resolution to both electrochemical and materials-based measurements. Each VersaSCAN is based on a common high-resolution, long-travel, closed-loop positioning system mounted to a vibration-resistant optical base. Different auxiliary pieces are mounted to the positioning system. These ancillary pieces (e.g., an electrometer, piezo vibration unit, or a laser sensor) provide functionality to the positioning system for different scanning probe experiments. VersaSTAT potentiostats and Signal Recovery Lock-in Amplifiers are integrated via ethernet control to make accurate measurements of these small signals.
-
product
Controllers
Applied Scientific Instrumentation
100 MHz Microcontroller for faster command processing and servo controlClosed-loop DC servo control of up to four motorized axesFirmware upgradeable via serial connection0-10V DAC for single piezo axis controlRemembers last position on power down/upLCD display shows axes coordinates and status“Zero” and “Home” buttons for simple stand-alone operationsUSB or RS232 serial control with baud rates to 115200 BaudCompact ergonomic tabletop control unit 6”D x 9”W x 3”H (16½ x 23 x 9 cm)
-
product
Multi-Axis Stage Controller
MS-2000-WK
Applied Scientific Instrumentation
*100 MHz Microcontroller for faster command processing and servo control.*Closed-loop DC servo control of up to four motorized axes.*Firmware upgradeable via serial connection.*0-10V DAC for single piezo axis control.*Remembers last position on power down/up.*LCD display shows axes coordinates and status.*"Zero" and "Home" buttons for simple stand-alone operations.*USB or RS232 serial control with baud rates to 115200 Baud.*Compact ergonomic tabletop control unit 6"D x 9"W x 3"H (16 x 23 x 9 cm).
-
product
Piezo Sensors
TE Connectivity (TE) piezoelectric sensors provide durable vibration, accelerometer, or dynamic switch elements for a wide range of markets and applications. Piezo sensors and transducers are available in various forms including film, cable, and miniature elements in standard and customized packages.
-
product
Piezo Drivers
Use Trek high voltage amplifiers to drive piezoelectric elements and piezoelectric (ferroelectric) material poling.
-
product
300mA One-Channel Amplifiers
Piezo amplifiers/controllers are designed for high precision positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
product
Piezo Unit Aging Tester
BK2028/BK2028A
We designed the BK2028 and BK2028A Piezo Unit Aging Testers for you to test your piezo electric vibration units for long term reliability. The BK2028 can test up to 50 units at a time, while the smaller BK2028A tests 20. Both models are easy to set up and can be stacked. They allow you to control the number of tests you you run so that you can run a large number of DUT's under exact conditions and make sure your piezo units will do what you expect them to do for the life of your products.
-
product
Laser Modules
The piezo laser modules include an attenuator, a filter wheel, an X-Y aperture, and a rotating waveplate. These compact laser modules can be integrated independently or can be daisy-chained together into laser beam delivery systems and have a damage threshold of 5 J/cm2. Attenuator modules connected together can also provide independent control of energy in multiple wavelength systems.
-
product
40 mA to 800 mA EN Series Analog System
An EN modular multi-channel solution is composed of an ENT power supply, one or more ENV controllers/amplifiers and a case. Depending on the specific application, multiple control modules can be used. This allows for the most cost effective solution for the highest precision piezo control system.
-
product
Ultra-thin Mass Flow Controller
DZ-100
The DZ-100 inherits the same CRITERION™ technology—a differential pressure detection system for laminar viscous flow ranges—used on HORIBA STEC’s MFC, the D500. This innovative technology controls the mass flow of various gases with high precision. As with the D500, the user-configurable DZ-100 supports multi-range and multi-gas applications. The compact design of the MFC reduces the internal volume of the internal gas flow path, and the optimized control algorithm improves response characteristics. It uses a compact CPU with high processing capacity, and the piezo drive circuit and control CPU are installed in the MFC module while the power supply components are housed in a separate small control box. Up to four MFC modules can be controlled by connecting them with the dedicated miniature connectors.
-
product
100mA One-Channel Amplifiers
Piezo amplifiers/controllers are designed for high precision positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
product
Multi Range/Multi Gas Digital Mass Flow Controller
SEC-Z500X Series
This is HORIBA's best selling model for digital mass flow controllers. It has multi-range/multi-gas functions enabling users to change the type of gas or full-scale flow rate on-site quickly and easily.With high accuracy +/- 1.0% S.P, piezo actuator valve, high speed response and being all-metal this mass flow controller is suitable for process yield improvement and simplified parts management. Digital/Analog, DeviceNet™, and EtherCAT® communications are all available.
-
product
Piezo Actuator Valve
PV Series
The Piezo Actuator Valve PV Series consists of piezo actuator valves with metal diaphragms and metal O-rings. When combined with a pressure sensor or flow rate sensor and ratio control unit (PCU series) you can use the Piezo Actuator Valve PV Series to create a pressure control or flow rate control system.
-
product
10mA One-Channel Amplifiers
USB connected devices have become common in lab environments. The nano box USB is a standalone piezo amplifier with 16 bit D/A resolution. Its small size and powerful amplifier includes a USB 2.0 interface that offers a variety of helpful commands.
-
product
Tunable Littman/Metcalf Laser System
Lion Motorized
Motorized Littman / Metcalf Motorized Tunable External Cavity Diode Laser, 630nm .. 1770nm, up to 100mW, hands-off operation, fully remote controlled wavelength scans, large mode-hop free piezo tuning range, narrow linewidth, free space and fiber coupled versions. Check our ar-coated diode stock list for availability.
-
product
Rapid Automated Modular Microscope
RAMM
Applied Scientific Instrumentation
*Featuring automated high-speed XY stages, precision piezo & motorized Z focusing, and a wide range of scanning options.*Configurable with infinity-corrected optics, dichroic filter cubes, multi-wavelength excitation and emission filterwheels, shutters, and detectors including cameras and photomultipliers.*Auto-focus, focus stabilization, tracker, and robotic specimen loader available.*Arrangement provides a solid platform for high throughput screening, genetic sequencing, experimental research, and much more.*Designed for flexible cost-effective OEM development using high quality high MTBF components to reduce cost and increase customer satisfaction.
-
product
Piezo Actuator Unit Multi Tester
BK2118
You are always improving your technology and we are right there with you. We developed the BK2118 to help you ensure that your piezo actuators are what you expect them to be. With up to 4 vibration sweeps and 2 channels, you can test a variety of characteristics at a speed that matches your product line. The core technology in the BK2118 is the same as our top selling BK2120C, with the same easy interface and the ability to back up your product's performance with saved test data. It also has the option of entering your own feedback so you can easily see how your DUT's perform during testing.
-
product
Video Autofocus Option
Applied Scientific Instrumentation
ASI's video auto-focus provides a simple focus control solution when using an analog video camera and any of ASI's products with Focus Control including standard and piezo XYZ stage systems, linear and gantry stage systems, and stand-alone MFC-2000 focus controllers.
-
product
Single Channel High Voltage Linear Amplifier
A600
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Low Noise High Precision High Voltage Amplifier
WMA-280
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
product
Hydrophones
Piezo is a critical element in producing a hydrophone for military and commercial underwater listening applications. Hydrophones utilize piezoelectric elements to detect sound pressure waves produced by underwater vessels, animals, and the environment. Hydrophones must have a flat frequency response that is proportional to the magnitude of the sound pressure wave. CTS piezo elements provide this critical function in hydrophones by providing excellent frequency response and high coupling factors necessary in hydrophone applications. CTS materials provide excellent electrical properties for hydrophone applications while allowing the ability to form the piezo element to the desired mechanical structure for the hydrophone.
-
product
Medical Ultrasound
Piezo elements form an essential component in medical diagnostics. Medical Ultrasound uses high-frequency sound waves to look at organs and structures inside the body. Medical professionals use medical ultrasound to view internal organs and during pregnancy to view the fetus. CTS provides both monolithic and composite piezoelectric elements used in medical ultrasound applications.
-
product
Bulk Acoustic Wave Technology
BAW
Macom Technology Solutions Holdings Inc.
MACOM’s BAW product portfolio is ideal for high performance Industrial, Aerospace, Defense, and Communications applications that require critical frequency filtering. Our high-performance RF filters enable our customers manage signal integrity in the 1 to 6 GHz frequency range. Bulk Acoustic Wave Resonators consist of two metal electrodes above and below a layer of a piezoelectric material. The piezoelectric material converts an electrical signal to a mechanical signal and vice versa. The metal electrodes provide the connections to/from the piezo material. The frequency at which resonance occurs depends on the thickness of the combined metal-piezo-metal stack. Advances in thin-film piezoelectric fabrication have enabled BAW resonators to meet RF filtering challenges up to 6000 MHz using standard MEMS fabrication process. High-performance BAW resonators-based RF filters are made of piezoelectric material having high Q-factor (>3000) and high coupling coefficient. Currently, no competitive technology provides the same high performance for RF filter applications when compared to BAW resonator-based RF filter up to 6000 MHz for the same size and cost.
-
product
Actuators, Adjusters, & Transducers
We offer a wide range of adjustment screws, micrometers, and kinematic positioners, as well as stepper motor, DC servo, high-precision piezo inertia actuators, and voice coil actuators. Additionally, our piezoelectric offerings include modular, screw, and replaceable-tip piezoelectric actuators, as well as Langevin transducers for ultrasonic welding applications. A wide variety of piezoelectric chips and stacks are also available.
