Distributed Systems
-
Product
Die-To-Wafer Bonding Systems
-
Several different D2W bonding methods are available and selected depending upon the application and customer requirements. In direct placement D2W (DP-D2W) bonding, the singulated dies are bonded to the target wafer one by one using a pick-and-place flip-chip bonder. Plasma activation and cleaning of the surfaces of the dies on the handler wafer are essential steps for establishing a high-yielding bond and electrical interface between the dies and target wafer. This is where the EVG320 D2W activation system comes in.
-
Product
SR/QE Testing System
PVE300
-
Industrial Vision Technology Pte Ltd.
Solar Cell Multi-function SR/QE Testing System is specially designed for Photovoltaic Industry to characterize the Optical Performance of Raw material, process wafer, finished solar cell, as well as small Module.
-
Product
Desktop Type AE Systems
-
Compared to the online remote AE systems, desktop type AE systems are connected to and accessible within the local network, either directly by wires or via wireless local networks. Such desktop type AE detection system is normally use with a computer or laptop on a desk or table on site or near the facility. It is usually conducted and real-time controlled by professionals to accurately locate the AE ‘Hits’ sources and analyse the AE data in full aspects. There are two types of AE systems that can be used as desktop type systems, the SAEU3H multi-channel AE system and the RAEM systems respectively.
-
Product
Slip Ring Test System
-
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
Product
Manual Semiconductor Metrology System
-
Front USB port enables easy storage of measurements and other data to flash drivesMTI Instruments’ Proprietary Capacitance Circuitry for Outstanding Accuracy and DependabilityNon-contact measurements76-300 mm diameter wafer rangeOptional wafer measurement ringsWafer stops for exact centeringEthernet interfaceFull remote control software (Windows compatible)Optional calibration wafers
-
Product
Power System Recorder
TESLA LITE
-
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
Product
ATCA 14 Slot System
-
14 slot custom system leveraging essential features of AdvancedTCA® to meet needs of industrial control application.
-
Product
Shock Test Systems
-
Accurately measure the fragility of products and evaluate how they respond to specific shock inputs.
-
Product
Portable Signal Conditioning System
SCS-800
-
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.
-
Product
Automatic Tablet Testing System
UTS 4.3
-
The UTS 4.3 LAB is a universal and fully automatic tablet testing system based on the long-proven UTS 4.1 - this was developed for industrial use and can be found in production worldwide. The UTS 4.3 LAB is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly and individually adapted to your needs and requirements. FDA regulations can be fulfilled with the optional FDA-21-CFR-Part-11 module.With UTS 4.3 LAB – as with the proven UTS 4.1 IPC – you can test round, oval, square and rectangular tablets as well as numerous special shapes. For difficult oblong tablets, the globally used Oblong Centering System (OZB) can also be integrated.
-
Product
Characterization System
System 7700
-
Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your your device, not on your test system.
-
Product
Optical Scanning Systems
-
that feature high scanning speed and accuracy. Our non-contact 3D scanners are ideal for 3D digitization of physical models, quality control and reverse engineering.
-
Product
Pegasus Verification System
-
The Cadence® Pegasus® Verification System is a cloud-ready physical verification signoff solution, which enables engineers to deliver advanced-node integrated circuits (ICs) to market faster. The groundbreaking technology delivers up to 10X improved performance on DRC runs and reduces turnaround time from days to hours.
-
Product
Laser Raman Microscopy System
RAMANforce/RAMANtouch
-
Nanophoton is the pioneer of confocal laser scanning microscopy and spectroscopic analysis. To celebrate, we relaunch our fastest and highest resolution confocal Raman microscope RAMANtouch/RAMANforce. With a newly designed spectrograph and the latest optical technologies, RAMANtouch/RAMANforce’s spatial resolution and sensitivity have been highly improved, making it the optimal solution for all applications.
-
Product
Vibro-Diagnostic Monitoring System
CTD-2060
-
Vibro-diagnostic Monitoring System CTD-2060 – is a device for continuous machines machinery condition monitoring and protection. It monitors and measures data from proximeters and vibration sensors through 6 channels at once.
-
Product
Automatic Welding Control System
-
The system is designed to move the tractor and position the welding head of the machine, which implements the industrial technology of one-sided automatic welding using the "cross-slide" method with obtaining guaranteed high-quality formation of the top and root of the seam.
-
Product
Application Specific LC Systems
Nexera MX
-
Higher throughput is of the utmost importance to laboratory efficiency and profitability. Nexera MX processes twice the number of samples as conventional LCMS systems in the same amount of time.
-
Product
Rack Data Acquisition System
TraNET EPC
-
The Elsys Data Acquisition Intrument TraNET EPC with its high channel density and robust housing is designed for highprecision measurements in industrial environments. It is a scalable system that may grow to a total number of 64 SE channels in one device. Several devices can be synchronized with the Elsys Sync-Link box.
-
Product
3-in-1 Test System
CIBANO 500
-
CIBANO 500 combines a micro-ohmmeter, timing analyzer, and a coil and motor supply. All important CB tests on all types of CBs can be carried out even when a station battery is not available.
-
Product
Spectrum Monitoring Systems
RFeye®
-
The product range includes entry level systems for dense network deployments through to best-in-class systems for military applications. RFeye Nodes are recognized as the "industry standard" for fixed remote distributed monitoring. In addition, we supply portable and vehicle based systems and a range of RFeye Arrays that are an extremely cost-effective alternative to traditional direction finders
-
Product
Antenna Training and Measuring System
-
The complete Antenna Training and Measuring System includes a set of 1 GHz antennas, a set of 10 GHz antennas, an RF Generator, a receiving system, and the Data Acquisition and Management Software for Antennas (LVDAM-ANT), a user-friendly software operating under the Microsoft® Windows™ environment. The receiving system consists of a rotating Antenna Positioner linked to a Data Acquisition Interface connected to the USB port of a personal computer.
-
Product
Solar Simulation Systems
-
PET Solar Simulators consist of a Light Source with a built-in Lamp Power Supply. The Solar Simulator has an ellipsoidal reflector that surrounds the lamp and collects most of the lamp output. The radiation from the lamp is focused onto an optical integrator that helps produce a uniform diverging beam. The beam is diverted 90° by a mirror onto a collimating lens. Special filters are placed between the mirror and the collimating lens to shape the radiation spectra to match various air masses. The output is a uniform beam that closely matches the sun's radiation spectra for a given air mass. Various models offer different areas of illumination. Each model can be manufactured to simulate the sun's radiation for different air masses.
-
Product
Analysis System
Trident (EDS-EBSD-WDS)
-
The Trident Analysis System combines the latest advances in Energy Dispersive Spectroscopy (EDS), Electron Backscatter Diffraction (EBSD), and Wavelength Dispersive Spectrometry (WDS) in a single analytical tool. With the Smart Features included in the easy to use EDAX analysis software, each technique can be optimized and used independently or they can be combined to provide seamless integration, resulting in comprehensive data collection that can then be shared between the different techniques.
-
Product
Automatic and Accurate Inspecting Systems
Circuit AOI
-
The Circuit AOI system is designed to perform automatic and accurate inspecting systems. It integrates rigid mechanical system with advanced vision technology and manufactured and tested by strict is standards. It is suitable for circuit inspection for PCB/FPC, verification and repair. Innovation and unique inspection algorithms are applied to inspect open, short, protrusion, nick, scratch, pin hole, island, line width/space violation, object missing and others defects. AOI system can use offline setup project and check results. It will improve the throughput.Compare to halogen lighting, the full angle LED lighting of Circuit AOI can obtain the best image contrast and is good for different panel type inspection.
-
Product
System
SYS-36
-
Systems with 36" chambers tend to be a customer favorite for their flexibility. They are easily used for many different types of coatings. Often times they are best utilized in a prototype or multi part production facility where a specialized system such as a dual chamber box coater is not required. They are, however, still configurable for specialized processes.
-
Product
Vapour Permeability Measurement System
-
Mass Spectrometer vapour permeability measurement system which works across every gas or group of gasses used in modern engineering. This is important as vapour permeability issues effect many performance and safety critical aspects across the engineering industries.
-
Product
Gel Strength Test System
LD-LGST-A10
-
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
Product
True Concurrent Test
TestStation Duo
Test System
The TestStation Duo is a true concurrent test system with independent test modules providing fast in-circuit test throughput and lowering high-volume production costs.It effectively doubles the test throughput of conventional in-circuit test systems, without doubling capital equipment costs or increasing manufacturing floor space, by combining two complete and independent test modules inside a single tester frame.
-
Product
Gunshot Detection & Localization System
-
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
Product
Curing System by Ultraviolet-Ray
Others
-
This is the relay amplifier box for the multi-point type UV monitors. Received UV light intensity is converted to electric signal for transmission. This allows distance between the light receiving inlet and the controller to 10 meters maximum.
