Distributed Systems
-
Product
Analysis Tool for ECU Networks and Distributed Systems
CANape
-
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware, CANape can store multiple gigabytes of data per second. Calibration data management and convenient measurement data evaluation including data management as well as reporting make CANape a complete tool for ECU calibration. Of course, CANape also provides access to bus data, diagnostic data and analog measurement data.
-
Product
Distributed Control Systems
-
As the heart of plant-level digitalization, ABB's Distributed Control Systems (DCS) are designed to transform your multi-faceted, 24/7 process operations. Our market-leading control architecture constantly monitors and drives plant productivity, maximizing asset utilization, process efficiency and production quality. A focus on availability, safety and cyber security ensures the protection of your people, assets and equipment. And by maintaining tight controls over raw material consumption, plant energy levels and waste by-products, ABB DCS solutions help to significantly reduce environmental impact.
-
Product
CW Transmitters
-
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
Product
cDAQ-9185, 4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785064-01
Chassis
4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9185 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
Product
Air Circuit Breakers
-
Mitsubishi Electric Automation, Inc
Low-voltage air circuit breakers (ACB) can be used as the main circuit breakers of power distribution systems in buildings, factories and ships. The AE-SW series offers a "fixed" type or "drawout" type option. This ACB series ranges from 630 amps to 6300 amps and provides high-level circuit monitoring as well as friendly networking capablities for a wide range of applications.
-
Product
Multifunctional Power Meters
-
Advanced stationary devices designed to measure, monitor, and analyze electrical quantities, energy consumption, and power quality in industrial and power distribution systems.
-
Product
DAS
-
The Distributed Antenna Systems (DAS) function is to enhance the performance of a wireless network coverage of a specific area. DAS is a network of antennas which are all connected to the same source. The DAS solution is more efficient than having a large single antenna to cover an area and that’s why it is highly suited for in-buildings service and a restricted outdoor area. Amphenol Procom offers a wide range of both indoor antennas and passive devices, especially for Public Safety applications.
-
Product
System Integration
-
Eastern OptX now offers System Integration for all of our equipment along with other instruments including: RF, microwave, and Optical test equipment, power conditioning, distribution, and back-up, system controllers, and data recording devices. We also offer test solution development including mechanical design, rack layout, and custom control software. Eastern-OptX will help you to design and develop your test solution and deliver a completely assembled and tested system.
-
Product
Resistors
-
A passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.
-
Product
Video Distribution Systems
VDU-100 Series
-
Systems Engineering & Management Company
SEMCO'S tactical military products have been developed in response to the requirement for near real-time, high-quality, encrypted video and sensor data capture, transmission and distribution in support of covert and overt military operations. These products provide for unprecedented audio-video and data communications from warrior-to-warrior as well as from warrior-to-command. Transmission modes include tactical and handheld radios, wireless and wired LAN, SATCOM, wireless Mesh, and Cellular, with full motion video capability in as low as 125 Kbps bandwidth. Video resolution, bandwidth and frame rates are adjustable, with high quality video frames capable of being transmitted in bandwidths as low as 9 Kbps. These products include video recording, with both local and remote download capability, as well as remote video enhancement, pan, tilt and zoom control, and multiple NTSC/PAL camera and imaging device interfaces. With administrative and password control, these products provide for unlimited remote viewing on PCs, Androids, iPhones and iPads anywhere in the world.
-
Product
ETAP ADMS
Advanced Distribution Management System
-
Advanced Distribution Management System must offer flexible solutions to address the core requirement of the new digital grid to provide resiliency and reliability to the network while having the scalability to intelligently and proactively assess the outcome of the operations and contribute to the new requirements to minimize network cost and improve asset optimization.
-
Product
Reactors
-
Chengdu Mengsheng Electronics Co., Ltd.
Reactors (also called inductors) are key power equipment used to regulate current, voltage and harmonics, and are widely used in power transmission, distribution systems and power electronic equipment. Our reactor products include single-phase reactors, three-phase reactors, air-core reactors, iron-core reactors and, which can meet the needs of different application scenarios. Designed and manufactured with high-quality metal materials and insulating materials to ensure high efficiency and safety and stability, and provide a variety of cooling methods such as natural cooling, forced air cooling and oil immersion cooling, suitable for various environmental conditions. With excellent performance and reliable quality, our reactor products can effectively improve the stability and reliability of the power system and meet the stringent requirements of modern power systems.Browse our electrical reactor products, if you need customization, please contact our team.
-
Product
Digital Cable Phasing Meter
PMT3000
-
Power Measurement Technologies Inc.
The PMT3000 Digital Cable Phasing Meter facilitates the testing, maintenance and installation of electrical distribution systems. Voltage magnitude, phase angle, phase rotation, frequency and tap capacitance measurements are provided in one convenient battery powered hand-held instrument.
-
Product
Fluke Battery Tester And Analyzer For Stationary Battery Systems
-
Fluke Battery Analyzers are the ideal test tool for maintaining, troubleshooting and performance testing individual stationary batteries and battery banks used in critical battery back-up applications in data centers, telecom networks, power distribution systems and more. With an intuitive user interface, a compact design, and rugged construction the Fluke Battery Analyzers are designed to provide optimum performance, test results and reliability.
-
Product
DAS Antennas
-
In-Building Distributed Antenna System (DAS or i-DAS) antennas are low profile and designed to be mounted discreetly to a hard or tiled ceiling. Used in a series throughout large buildings, campus areas or even in below ground sections of a building the antennas can provide a distributed LTE or Wi-Fi signal to where it is required most. With a growing demand for in-building connectivity and higher data rates, larger smart or connected buildings require a series of antennas in order to distribute signal around the building or campus area.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-50
-
CLKSYNC-50 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
PXI MultiComputing Remote Control Module
Remote Control
PXI MultiComputing Remote Control Modules enable PXI systems to transfer data at multigigabytes per second with only a few microseconds of latency. You can use these models in applications such as real-time tests, hardware-in-the-loop (HIL) tests, and structural tests that need a large number of distributed PXI systems to share data with low latency.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-40
-
CLKSYNC-40 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
Shared Memory Network
-
Avionics Interface Technologies
AIT's Shared Memory Network (SMN) interface modules provide host systems with an interface to a high speed (2.125 Gbps) optical data network which can be used to share data, in real-time, between multiple distributed systems.
-
Product
DCS Intelligent Remote Redundant Ethernet I/O Expansion
-
Intelligent Remote Redundant Ethernet I/O expansion unit for the Distributed Control Systems (DCS systems). Supports Modbus TCP Protocol and can be used with PC's or PAC controllers. Has two processors for added redundancy.
-
Product
Disciplined OCXOS
-
GPS Disciplined OCXOs (Oven Controlled Crystal Oscillators) are a range of advanced clock modules which provide electrical timing functionality for distributed network systems. These units primarily revolve around the 1PPS (pulse per second) timing synchronisation signal produced by a GPS frequency receiver which is derived from transmitted timing information received from GPS satellite systems.
-
Product
Downed Conductor Detection
-
Schweitzer Engineering Laboratories, Inc.
Downed conductor detection technologies detect many high-impedance faults on a distribution system, improving safety as well as mitigating wildfire risk.
-
Product
Encoder
SFT3226SA
-
Hangzhou Softel Optic Co., Ltd.
SOFTEL SFT3226SA multi-channel encoder is our newest professional SD audio & video encoding and multiplexing device with powerful functionality. It adopts the slot structure with one device supporting maximum 2 SFT3226SA modules. Each module can support 16 channels and work standalone. It is equippedwith 16/32 CVBS channels input. It can multiplex the 16/32 encoded TS to generate a MPTS and 16/32 SPTS output through GE output port and one MPTS output through 2 ASI output ports. In conclusion, its high integration and cost-effective design make this device widely used in variety of digital distribution systems such as CATV digital head-end, satellite and terrestrial digital TV, etc.
-
Product
RangeNet software
RangeNet
-
Command and Control Technologies Inc.
RangeNet software is designed to simplify creation of distributed range control systems and enhance situational awareness of command, safety, and range personnel. It is a modular framework that is easily adapted and extended to a variety of mission types anywhere in the world. It integrates planning, configuration, simulation, training, mission execution & post mission analysis under an integrated architecture. RangeNet is a “plug-in” software module of the Command and Control Toolkit™ (CCTK), the real-time command and control middleware from CCT.
-
Product
Extension Unit
ZET 452 MP
-
The ZET 452 MP extension unit improves the capabilities of electric circuit parameter control devices:*increases the number of measuring circuits;*makes it possible to build distributed systems for cable networks checking.
-
Product
GO-2000 Goniophotometer
-
Hangzhou Everfine Photo-E-Info Co., LTD
GO-2000 is a highly automated luminaire light distribution performance test system, mainly used for all kinds of indoor lamps, road lamps and floodlights ( add B-β test accessories) light distribution performance test, total luminous flux test and electrical parameters (voltage, current, power, power factor) measurement.
-
Product
Aircraft Power Distribution
-
CorePower® aircraft power distribution systems from Astronics replace traditional mechanical breaker systems with intelligently controlled solid-state switches to provide next-gen reliability and safety.
-
Product
Validation System
FLEX BMS
System
The FLEX BMS™ Validation System is a quick-connecting, highly flexible test system for rapid evaluation of centralized, single-board and distributed battery management systems. Utilizing Bloomy’s industry-leading battery cell simulators, COTS instrumentation, industry-standard connectors, and models that run in real-time, the FLEX BMS™ Validation System can easily be reconfigured to test a wide variety of BMSs. The FLEX BMS™ Validation System is used by national and regional safety and standards labs for certifying the BMS for a wide array of e-mobility products and applications.
-
Product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-01
Chassis
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
Product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-01
Voltage Input Module
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
