Photodiode
convert's light into current.
See Also: Diode, Laser Diode, Zener Diode, Diode Test, Photodiode Arrays
-
Product
Photodiode
-
A high sensitivity receiver in a fiber pigtail coupled package, it includes a high speed InGaAs avalanche photodiode with a high gain TIA in a hermetically sealed coaxial package. It incorporates an LC/UPC pigtail and a flexible printed circuit (FPC). The signal GND and a receptacle are electrically isolated in this APD receiver.
-
Product
Full Range Photodiode Array UV-VIS-NIR-SWIRLaboratory Spectroradiometers
-
The SR-Series of full range laboratory spectroradiometers is ideal for a wide range of applications, including Solar radiance and irradiance measurements. Solar simulator test and classification. LED, laser, light source metrology. Radiometric calibration transfer. Remote sensing applications.
-
Product
16-element Si photodiode array
S12362-321
-
The S12362/S12363 series is a back-illuminated type 16-element photodiode array specifi cally designed for non-destructive X-ray inspection. These are modified versions of our previous products (S11212 series: 1.575 mm pitch). The pitch has been changed to 2.5 mm. The back-illuminated photodiode array is also simple to handle and easily couples to scintillators without having to worry about wire damage because there are no bonding wires and photosensitive areas on the back side.
-
Product
PIN Photodiode
-
PIN photodiode is a kind of photo detector, it can convert optical signals into electrical signals.This technology was invented in the latest of 1950's. There are three regions in this type of diode. There is a p-region an intrinsic region and an n-region. The p-region and n-region are comparatively heavily doped than the p-region and n-region of usual p-n diodes. The width of the intrinsic region should be larger than the space charge width of a normal p-n junction. The PIN photo diode operates with an applied reverse bias voltage and when the reverse bias is applied, the space charge region must cover the intrinsic region completely. Electron hole pairs are generated in the space charge region by photon absorption. The switching speed of frequency response of photo diode is inversely proportional to the life time. The switching speed can be enhanced by a small minority carrier lifetime. For the photo detector applications where the speed of response is important, the depletion region width should be made as large as possible for small minority carrier lifetime as a result the switch speed also increases.
-
Product
*Photodiode Energy Sensors
-
Ophir photodiode laser energy sensors are able to measure low energy pulses down to 10pJ at frequencies up to 20 kHz. Silicon photodiodes for the UV and visible spectrum and Germanium photodiodes for infrared.
-
Product
UV Index Measurement
-
The sglux UV-Index sensors measure the UVI with a worldwide unique low measurement uncertainty of less than 5 %. This makes our sensors compliant to the highest measurement precisions class one according the DIN/EN 5031-11, chapter 8. Since 2018 our product UV-Cosine_UVI (ERYCA) is appointed for public authority tasks: The German Federal Office for Radiation Protection (BfS) services 27 measurement points in Germany for public information of the daily UV-Index. Twenty of these points (Andernach, Chieming, Duderstadt, Fichtelberg, Genthin, Giessen-Wettenberg, Schauenburg-Kassel, Langen, Lueneburg, Munchen-Neuherberg, Norderney, Belm/Osnabrueck, Schauinsland, Tholey, Todendorf, Waldhof-Falkenstein, Waldmuenchen, Wurmberg, Zingst and Zirchow) use the sglux ERYCA to obtain the local UV-Index value. In 2017 ARPANSA (Australian Government’s primary authority on radiation protection and nuclear safety) began replacing the existing biometers with SiC photodiode UV sensors (sglux ERYCA) at all network sites. There are currently thirteen measurement sites in Australia that have been upgraded to the new sensors.
-
Product
High-resolution, SWIR megapixel camera
Wildcat+ 1280 Series
-
The Wildcat+ 1280 series is based upon a state-of-the-art InGaAs photodiode array with 1280×1024 pixels and 5 μm pixel pitch. The camera offers superior, high-resolution SWIR imaging capabilities, comes in a versatile and industry-proven Wildcat camera package (GenICam compliant) and offers advanced on-board image processing.The Wildcat+ 1280 camera outputs full frame images at 120 Hz via either a CameraLink or USB3 Vision interface.The Wildcat+ 1280 is suitable for semiconductor inspection, display inspection (mobile phone and TV), microscopy and laser beam analysis.Benefits & Features• Compact and industry-proven camera design• High-resolution SWIR imaging• Advanced on-board image processing performance• GenlCam compliant• Flexible optical mount and lens options
-
Product
UV-Vis & UV-Vis-NIR Systems
-
Our range of powerful and productive UV-Vis and UV-Vis-NIR molecular spectroscopy systems offers options for any optical application. The Cary 60 Spectrophotometer has a unique Xenon flash lamp to enable remote sampling, while the Cary 4000 allows you to measure highly turbid solutions without an integrating sphere. The Cary 8454 photodiode array captures the complete UV-Vis spectrum (190-1100nm) in less than one second.
-
Product
10G Pin Photoreceivers
-
Macom Technology Solutions Holdings Inc.
MACOM offers PIN photodiode based photoreceivers in a variety of packages, including OEM module and instrument-style. A wide range of 10G solutions are available for applications up to 15 Gb/s covering 800-1650 nm wavelengths.
-
Product
Fiber Photodiode Power Sensors
-
These interfaces provide communication between an attached sensor and a PC or other external control unit. They are designed to be controlled via an external device or operated autonomously using the analog output; there are no controls or display screens.
-
Product
Optical Sensors
-
Analog Devices optical sensors are optical sensing front ends that include integrated ultra-low noise amplification and high performance photodiodes. These solutions are used to achieve the highest performance for instrumentation, industrial, or clinical applications; or to optimize a solution to achieve the lowest power dissipation at a given performance level for battery powered and portable applications.
-
Product
OLED Life Time Test System
-
A system for measuring measurement items (brightness and so forth through Voltage, Current, and Photodiode) and their lifetime in intervals of set time, while supplying power to multiple (32 Channel) OLED panel stably.
-
Product
Detectors
-
A detector head comprises one or more photodiodes each with an appropriate optical bandpass filter, diffuser, lens assembly, integrating sphere or other optical elements. Detector heads are calibrated in the Gigahertz Optik GmbH's calibration laboratory.
-
Product
Ultra-Low Noise 2 kHz Photoreceiver w/ Si-PIN Photodiode
PWPR-2K-SI
-
Picowatt Photoreceiver series PWPR-2K with switchable gain (10 to the 9th V/A, 10 to the 10th V/A) and a bandwidth from DC to 2 kHz is the perfect choice for cw-measurements, time resolved signal acquisitions and highly sensitive modulated measurements. Si and InGaAs models cover the wavelength range from 320 to 1700 nm.
-
Product
PD-200 High-Speed High-Power Photodetector
-
These high speed photodiode, PD-200, is hermetically sealed, high reliability, low harmonic distortion photodiode modules designed for high optical power applications with minimum bandwidths of 20 GHz. The device is well suited for receiver applications with optical pre-amplification, and is available either with or without an internal 50Ω termination. The photodiode module is available in either a V-connector package or a miniature surface mount package with CPW (coplanar waveguide) RF output.
-
Product
UV Photodiodes
-
Active area from 0.06 mm² to 36 mm² and quadrant photodiodes for position detections. Spectral response for broadband UV or filtered for UVA, UVB, UVC or UV-Index. Various entrance optics and housings options available (TO or SMD). Our own SiC photodiode chip production since 2009 also available with VUV sensitivity. PTB (German equivalent of NIST or NPL) measured high radiation hardness. 350°C high temperature stable photodiodes available. Photodiode application guide.
-
Product
Photodiodes & Arrays
-
Excelitas utilizes Silicon and InGaAs materials for our photodiodes to provide detection from 220 nm to 1700 nm. These devices are offered in a variety of sizes to meet customer sensitivity and speed requirements. Many different types of photodiodes are available to serve various unique applications.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
UV Sensors
-
With analog (4-20mA, 0-5V, 0-10V) or digital (USB, Modbus) output, also available with Android device (incl. app). SiC photodiode chip based Broadband UV sensitivity or filtered for UVA, UVB, UVC or UV-Index spectral sensitivity. Our sensors are also available with logarithmic signal transduction, linearity from 0 … 1500 mV. Calibration services available at our Berlin facility prior to delivery and after use
-
Product
Light Meters
-
Light Meters are used to measure the light output of an illumination source for a number of optical applications. Light Meters are measurement devices that feature photodiodes to determine the level of light transmitted from a source. Light Meters possess simple, easy to read screens upon which measurements are displayed in one or more photometric units. Most Light Meters possess traceable NIST certification for proof of accuracy.
-
Product
DWDM High Power DFB Buttterfly Laser
CA1782-XXX-XX-BT
-
The CA1782-XXX-XX-BT DWDM High Power DFB Buttterfly Laser component is characterized for use as a CW optical source in CATV and DWDM networks. The CA1782-XXX-XX-BT is dc-coupled with a built-in TEC, thermistor, and monitor photodiode. The device is mounted in a 14-pin, OC-48 pinout compatible butterfly package with the optical isolator mounted on the TEC. The CA1782-XXX-XX-BT incorporates a high efficiency coupling scheme to deliver 40 mW, 50 mW, 63 mW and 100 mW of CW optical power.
-
Product
Optical Power Meter
HOPM-3211
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HOPM-3211 optical power meter is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optic fiber networks. An Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, wide range of power measurement, high accuracy, user self-calibration function and reference power level storage.
-
Product
Compact Juno USB Interface
Juno 7Z01250
-
*Virtual laser power meter - From sensor to interface to PC - no power source needed*Plug and play with all standard Ophir smart sensors*Use with StarViewer free Android app to turn your smartphone / tablet into a power meter*Record every energy pulse at up to 10 KHz*Log power and energy, average, statistics, histograms and more with included StarLab application*New: Pulsed Power measurements with Thermopile sensors*New: Low Frequency Power on Photodiode sensors - power measurement based on pulse cycle (for VCSEL)*System Integrator Tools included: LabVIEW VIs, COM Object Interface*Very compact - is just an extension of the smart plug
-
Product
X-Ray And Gamma Detector Systems
-
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
Product
High-Speed Digital Output
-
High-speed digital output photocouplers (optocouplers) are optically coupled high-speed, totem-pole output isolators containing a GaAlAs LED on the input side and a photodiode and signal processing circuit on the output side in a single chip.
-
Product
Laser Diode
-
Is a Polarization Maintaining CWDM Coaxial DFB-LD for CWDM analog communication, CATV return-path, laboratory instrument, and R&D applications. This cost-effective, high reliability DFB laser chip has a selectable wavelength with range between 1270 nm to 1610 nm. The versatile DFB-CWDM also features a built-in InGaAsP monitor photodiode, built-in optical isolator and 4-pin coaxial- pigtailed package, single mode coupling, and an FC/APC connector. Contact Optilab for more information.
-
Product
Photodiodes
-
Opto Diode manufactures high quality standard and custom photodiodes. Our wide range of standard device feature low dark current and low capacitance. The silicon detectors are ideal for general purpose applications, laser monitoring, position sensing, measuring photons, electrons, or X-rays, or for detecting sun and rain applications. The devices operate from the deep UV to the near-infrared wavelengths.
-
Product
Low Input Bias Current Op Amps (≤100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Current to Digital
-
Analog Devices’ breakthrough current-to-digital converter technology is backed by award winning expertise to help solve your medical, industrial, and security application needs. Our high speed, high resolution ADC modules enable improved CT scanner data acquisition, photodiode sensors and power monitoring, spectroscopy, and high channel count data acquisition systems.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
