High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. Also known as: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
Rad Hard GaN Drivers
The space market has been driving towards more efficient power management solutions. Part of the drive includes the use of Gallium Nitride Field Effect Transistors (GaN FETs) for power conversion. GaN FETs have higher power conversion efficiency and have more natural immunity to radiation, due to them being wide-bandgap semiconductors. Equally important is the use of the correct driver that will allow reliable operation and maximize the benefits of the GaN FETs. Some of the key driver requirements are: a well-regulated gate drive voltage; high source/sink current capability and a split driver output stage.
-
product
Mobile High-Power System for High-Voltage Solid Delectrics Testing.
HVTS-HP series
The HVTS-HP series systems are designed for high-voltage withstand testing of solid insulation with higher levels of DC or AC voltage (UDC ≤ 140 kV; UAC ≤ 100 kVRMS, f = 50 Hz).
-
product
Test Set With Control Unit
Supreme Instrument Laboratories
Single Phase A.C. High Voltage Test set (BDV Flash Test) suitable for operation on 230 Volts, A.C. 50 Hz., designed for carrying out dielectric test on transformers, electrical switchgears, and installations. It operates on single phase A.C. and provides an output voltage zero to maximum rated voltage.
-
product
ATC Cabinet Switch Pack Tester
ASPT-5300
The ASPT-5300 ATC Cabinet Switch Pack Tester (HV) will run a series of comprehensive tests on the Model 2202-HV HDSP/FU. The Model 2202-HV HDSP/FU is an important component in the ATC Cabinet Monitoring System.The Model 2202-HV HDSP/FU not only provides field output drivers, but also monitors the voltage and current for each of the field outputs.
-
product
37-Pin D-Type Female Straight PCB HV
40-963-037-SF-HV
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
Cable Route Tracing and Identification
Cable pinpointers and fault locators from Megger make the process of cable route tracing and identification quicker and more accurate. These pinpointing systems are portable for everyday fieldwork and provide services from power and telecoms to water, rail and gas utilities. HV and LV buried cables can be traced to a depth of up to 5m.
-
product
Series Resonant System
HTXZ / 100
Wuhan Huatian Electric Power Automation Co., Ltd.
Suitable for large capacity, high voltage capacitance test and preventive test.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m HV, Exit Away From Pin 1
A050DF4-C-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Power Converter Test Solution for HEV/EV and HEMS
EV1003A
The hybrid-electric and electric vehicle (HEV/EV) market has been growing rapidly. The addition of these vehicles in the automotive market brings with them new challenges in design and manufacturing. Probably the most noticeable change is the addition of high-voltage, high-power batteries to a platform that is traditionally 12 volts. Hybrid electric and full electric vehicle batteries are 300 volts and higher. These high voltages bring with them additional costs and risks.
-
product
High Voltage 9 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
9 Pin D-type Connectors & Cables
These standard voltage and high voltage 9 Pin D-type connectors are used for both PXI & LXI switching and simulation products for low density applications.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Away From Pin 1
A050DF4-C-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
High Voltage Probes To Measure Primary Waveforms With A Power Analyzer
Volt Litewire
The Litewire is a true RMS meter designed for use by electric utilities to sense currents or voltage waveforms from the primary side of their distribution networks.
-
product
Bridge Decking Testing Equipment
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
product
High Voltage Test Equipment
A hipot test is conducted by ensuring no current flows from one point to another on a circuit. A hipot test will take two conductors that should be isolated from one another and passes a high voltage between the two points. The current which flows between these points is then measured. If too much current flows, this would indicate that the points are not well isolated and the test will fail.
-
product
Modules - Modules, Automotive
Automotive modules from Vishay feature a range of technologies including FRED Pt®, High Voltage, MOSFETs, and Silicon Carbide (SiC).
-
product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
product
Embedded Synchro - Resolver -
LVDT I/O Cards
Computer Conversions Corporation
100% Transformer Isolation is offered for all AC I/O, and various Isolated DC converters are available as standard product, eliminating concerns for ground-loops, ground interjected (intermittent and ghostly) field noise, inductive surges, differing potentials, and high voltage field transients from effecting the card itself, the sensitive ISA bus backplane and any other device or system sharing these signals.
-
product
Standard Voltage 37-Pin D-Type Connector & Cable Accessories
The Standard Voltage 37-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution.Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
product
Cable Assy 9-Pin D-Type, M/M, 2m, HV
40-970-009-2m-MM-HV
9-Pin D-Type Male to Male Cable Assy, High Voltage, 2m Long
-
product
Acute High Voltage Differential Probe, 10x/100x, 25MHz, 700V
ADP1025
*USB Powered (or Power Bank)*Bandwidth up to 25 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
product
LXI High Voltage Matrix - 400V 50x4 Matrix Plugin Module
65-218-101
The 65-218-101 plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 400V. This version of plug-in includes access to the chassis backplane.
-
product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
product
AC High Voltage Test Sets
We are highly reckoned among clients for manufacturing and exporting an excellent AC High Voltage Test Set. It is specially engineered and developed for performing varied tests on air conditioner. As to satisfy clients' requirements, we can also optimize this test set. Manufactured in accordance with industry standards using supreme grade raw materials, this AC High Voltage Test Set is offered to clients at industry leading price. Before the final dispatch in market, this test set is stringently tested on varied quality parameters.
-
product
Transformer Heat Run Tester
1. Suitable for all transformers below 240MVA heat run test and winding resistance testing.2. Printing heat run data automatically.3. With double power supply, can test high voltage side and low voltage side simultaneously and test any operation respectively.4. With anti breakage protection function of inductive test items.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
High Voltage Switching Matrixes -15KV – 48Ch
H730035
Fast ATE technology: Modular, scalable and top flexible approach Minimum wiring and easy maintenance; LabVIEW drivers
-
product
Test Enclosures
The HV test hood, developed by us in accordance with EN50191 standard (erection and operation of fixed and temporary electrical test installations), is designed for testing large quantities in ongoing production. The ergonomic design ensures fatigue-free operation even during repetitive work sequences. Equipped with all safety-relevant functions, such as safety switch and locking of the hood cover during the test sequence, the operator is optimally protected at all times.The interchangeable adapter plate within the test cell allows quick adaptation for different test conditions and test situations.
-
product
Digital Input Board
VME-1129
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 2m, HV
A037DF4-T-HA200
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
