Testers
find the limits of a design and assure designed requirements.
See Also: Test, Testing, Specimen, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers, Checkers
-
Product
Filter Testers
-
All filter test equipment from TSI, used for testing efficiencies of filter media and a variety of air filters, including high and very high-efficiency filters, respiratory filters, cartridges, and protective garments, is known for its simple and reliable operation.
-
Product
Insulation Testers
-
The Zeta series consist of the insulation testers. Zeta series insulation testers have proven invaluable in the testing of insulation resistance measurement for industrial applications such as motors, electrical panels, cables, telecom industry, defense and many more.
-
Product
Cable Testers
-
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
Product
Adjustable Press Plate Bed of Nails Testers
Prober Adjustable Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Ground Resistance Testers
-
IP67 protected top in the industry Test all ground types from Class A to Class D with a single meter Wide 0 to 2000 measurement range Minimize cabling time with innovative earthing rods and cable winder
-
-
Product
Cable Testers
DMX ADAPTER
-
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Product
Capacitive Discharge Testers
-
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 16A option for testing large equipment.
-
Product
Puncture Testers
-
Mechanical puncture testers check the puncture resistance or hardness of materials like dry wall, foam boards, cardboard, etc. They are ideal for handheld penetration tests or mounting to a test stand and intrinsically safe in hazardous environments. An optional handle is available.
-
Product
Serial Bit Error Ratio Testers
-
Developing next-generation technology requires world-class signal integrity and analysis capability. Keysight offers the widest choice of serial bit error ratio test (BERT) products for accurate and efficient characterization, compliance, and manufacturing test for digital interfaces in computer, video, datacom, and telecom applications operating up to 40 Gb/s. Keysight’s breakthrough technology enables you to conquer even the most difficult measurement challenges.
-
Product
PoE Testers
-
The Essential Tool for Installing and Maintaining NetworksThe LanMaster 35 is a new handheld tester used for installing and maintaining Local Area Networks (LAN) using Power over Ethernet (PoE).
-
Product
Electrical Installation Testers
-
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
-
-
Product
Bottle Cap Torque Testers
-
NJY Series Torque Tester is designed to measure the open force and lock force of the caps of bottles, spout bags and flexible tube packages.
-
-
Product
Electrical Testers
-
A range of professional-grade tools designed for electricians and HVAC engineers to safely test, measure, and diagnose electrical circuits.
-
Product
Peel Testers
-
Imada offers motorized peel testers in vertical or horizontal configurations.The motorized test stand, digital force gauge and peel fixture apply tension to a safety seals, tapes and laminates.Special attachments and fixtures facilitate 45°, 90°, 180°, ‘T’ and rotary peel tests.Motorized peel testers offer speed control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All peel testers with digital force gauges have data output capability for analysis by optional data acquisition software.
-
Product
Insulator Testers
-
*Designed to test lightning arresters for damage or deterioration*Live line tester tests lightning arresters prior to energizing*For use on system voltages from 4kV to 25kV line-to-line and up to 69kV with optional add-on resistor sticks*Versatile for overhead and underground applications
-
Product
Battery Testers
-
When diagnosing a starting system issue, it is important to pinpoint the exact source of the problem to avoid warranty/replacement of the wrong part, reduce vehicle comebacks and maintain customer satisfaction. BA Series testers provide the detailed data needed to make the right call. Model Nos. BA5 and BA7 are economical enough to be used as triage testers at busy repair facilities. Put them in the hands of every tech in the shop and watch efficiency skyrocket.
-
Product
Vibration Testers
-
Guangzhou Amittari Instruments Co.Ltd
The Vibration Tester can display the parameters of “Displacement”, “Velocity” and “Acceleration” simultaneously; Applied to the periodic motion measurements to detect moving mechanical imbalances and misaligned. Designed for on-site measuring various mechanical vibration, for quality control, running time and prior equipment maintenance data. Selection of high-performance accelerometers to achieve accurate, replicable measurement It has a bearing condition measurement function.
-
Product
Cable Testers
CableJoG 64
-
CableJoG 64 can test up to 64 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in the cable testers memory to produce a pass/fail indication of each pin connection.
-
Product
Multifunction Testers
1663
-
The 1663 installation tester delivers the full-featured functionality and advanced measurement capabilities that professional installers need. It is compact and lightweight (less than 1.3 kg) and comes with a padded carrying and waist strap for convenient handling.
-
-
Product
Open Cup Flash Point Testers
-
Open cup flash point tester, Cleveland open cup flash point tester, automatic Cleveland open cup flash point tester, Automatic COC flash & fire point tester
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
MPO IL/RL Testers
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber also supply MPO Tester from Yokogawa, Agilent(Keysight), Optical Talk Set, fiber splitter PDL Loss tester, MTP Tester, fiber Return Loss & Insert Loss tester and other MTP/MPO testing solutions, you can find the most effective products in a reasonable price. Welcome to SunmaFiber. Contact us at Sales@SunmaFiber.com or Live Chat with us. Buy other fiber optic products on SunmaFiber. Save your money & time right now!
-
Product
Photovoltaic Testers
-
A range of products to verify safety and efficiency of photovoltaic installations. This range includes 1500V I-V Curve Tracers, Insulation testers (IEC/EN62446), designed to provide more and more functional solutions for the activities to be performed.
-
Product
AC Ground Bond Testers
440 Series
-
The 440 Series provides advanced 4-in-1 test capability in a convenient one-box solution. This new series performs AC Hipot (448 - 500 VA), DC Hipot, Insulation Resistance and 40A AC Ground Bond tests while taking up minimal production line space. The 440 Series is simple and easy-to-use; reducing setup time and increasing production line throughput for your application. With multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Learn about our 5 Year Warranty.
-
