Verifiers
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
Chained Data Test Support for 802.3at and 802.3bt PSE's
-
Intuitive graphical user interface. Configures up to 24 2-Pair or 4-Pair ports for "snaked data path" testing. Verifies all PSE connections in the defined data path. Sequences user-defined PD emulations and PSE powering.Verifies powering to user-defined loading on all selected ports. Configures looped data paths across the selected ports. Support of 802.3at / 802.3bt LLDP power negotiations (PSL-3424L).
-
Product
3.0mm Preset Controls Probe
CX-A3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
Product
Miniature Single Axis Accelerometers
-
Miniature piezoelectric accelerometers are required for applications demanding high frequency range, small size, and low weight. Product testing is necessary in today’s competitive marketplace in order to optimize designs, reduce defects, and improve customer acceptance and satisfaction. Shock and vibration testing offers a structured approach for verifying survivability in environmental influences that may be encountered during service and for precipitating incipient failures so they are not encountered by the end-user. PCB® accelerometers are used extensively for monitoring an object’s response to a programmed vibration input and for controlling the vibration profiles during testing.
-
Product
VIS-NIR Cameras
-
Surveillance cameras based on CCD/CMOS/ ICCD/ EMCCD/EBAPS imaging sensors sensitive in visible and near infrared range are widely used in many long range surveillance applications as independent imagers or as part of a bigger multi-sensor surveillance systems. Majority of VIS-NIR cameras are used for day level applications but an increasing number of these cameras is used to enable surveillance in both night and day conditions. In both cases it is important to verify performance of these cameras under varying illumination conditions from very dark nights to ultra bright days. Important missions can fail due to too low sensitivity of VIS-NIR cameras at night conditions (dark, noisy images) or due to too low dynamic at ultra bright day conditions (saturated, blurred images). Next, it is important to use VIS-NIR cameras that generate high quality images in order to achieve maximal effective surveillance ranges.
-
Product
Waterproof EC Tester High with ATC
ECTestr High
-
ECTestr Low tester series can measure natural water, verify reverse osmosis system operation and tap water quality. Check nutrient solution concentration in hydroponics applications. ECTestr High models measure salt water, wastewater, cooling tower water, and boiler condensate. Measure salinity for ponds and recirculating systems.
-
Product
Barcode Verification Systems
REA Check ER
-
The REA Check ER is a portable, battery powered barcode verifier. Its manufactures in conformity with international standards in Germany. The REA Check ER is a combination of a very small device which includes the powerful and comfort features of the REA VERIFIER product line. The small size and solid state construction makes this device a perfecr tool for portable barcode verification. The final result "Pass" or "Fail" is the central aprt of the verification report. The still quick available details allow a fast deeper analysis.
-
Product
Oil Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
oil analysis program is to verify that a lubricated machine is operating according to expectations. When an abnormal condition or parameter is identified through oil analysis, immediate actions can be taken to correct the root cause or to mitigate a developing failure.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
SureTest® Circuit Analyzer
61-164
-
*Measures voltage drop under load**Hot and neutral conductor impedances*Estimates Load on Line (ELL) up to 15A*Tests GFCIs and EPDs for proper operation*Super-bright OLED display*High accuracies*True RMS*Line and peak voltage*Identifies proper wiring in 3-wire receptacles*Identifies false (bootleg) grounds*Tests without disturbing sensitive loads*Verifies isolated grounds (with 61-176 adapter)*2-year warranty*12A, 15A, 20A load tests
-
Product
4.0mm Hazardous Live Parts Probe
CX-A4D
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts through top openings. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN61010-1, UL3101-1, and CSA 1010-1. The handle and stop face are made of Delrin. The rod is made of stainless steel.
-
Product
CT Polarity Tester
DIR CT
-
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
-
Product
4.0mm Hazardous Live Parts Probe
CX-4.0
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts through top openings. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN61010-1, UL3101-1, and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is made of stainless steel.
-
Product
Test Compliance
MX CTS Series
-
AMETEK Programmable Power, Inc.
A growing number of electronic products manufactured today have to meet international regulatory requirements for emissions and immunity. This is particularly true for products sold in the European community as well as a growing list of countries in the Far East. The California Instruments MXCTS System provides a cost-effective test solution aimed at verifying higher power product compliance to a number of AC and DC related harmonized test standards. The MXCTS system offers many of the same features and capabilities of the California Instruments CTS Series product line already in use at many EMC labs around the world.
-
Product
MCB Temperature Rise and Power Loss Test Bench
-
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
Product
High-Performance Application and Security Load Module
PerfectStorm 10/1GE Load Module
-
Keysight Network Applications and Security
Equipped with powerful multi-core, multi-threaded network processors, PerfectStorm 10/1GbE is designed to satisfy the testing needs of manufacturers needing speed flexibility in their testing resources. Networking equipment manufacturers building new equipment or service providers and large enterprises integrating this them benefit from testing and verifying performance and functionality prior to deployment.
-
Product
Matrix Code Verification Systems
REA MLV-2D
-
The REA MLV-2D is a matrix- and barcode verifier which has been developed in conformance to international standards. The measurement uses defined angeles distance and illuminations to achieve repeatable results and quality information.
-
Product
DCA-M Sampling Oscilloscopes
-
Built on Keysight's digital communication analyzer (DCA) technology, the DCA-M family is recognized as the industry standard for verifying optical transmitter compliance to communications standards. With single to quad optical AND electrical channels in a compact form factor, the DCA-M is ideal for both manufacturing and RND applications. Analyze both multi-mode and single-mode signals with the low-noise, high-sensitivity calibrated reference receivers. The variety of models along with the supporting software and compliance applications ensure you can measure with high precision, whether you analyze electrical or optical devices.
-
Product
Machinery Testing
-
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing products according to applicable standards. We help you not only verify the classification of your machinery, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm - SPST
50-294-112
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Customer Specific Tests
-
No matter whether you have developed a product without an underlying standard or extended a product beyond the standard – we verify your product to see if it conforms to the characteristics specified by you.
-
Product
Hydraulic Component Test Stand
Model 700
-
Model 700 Hydraulic Component Test Stand (HCTS). Designed to test heavy-duty, off-highway, closed or open loop pumps, the 700 gives you the capacity to confidently and efficiently verify the quality of your work. Test new or rebuilt pumps, motors, valves, and cylinders independently, and communicate their quality to your customers with the help of PowerNet TD, data acquisition software for transmission and hydraulic systems. Convenient work height with adjustable mounting track. 100, 200 or 300 HP drive motor options available. Variable Frequency Drive (VFD) controlled drive motor. 200 gallon (757 L) high-mount hydraulic oil reservoir for flooded pump supply. Combined kidney filtration and cooling loop for continuous cleaning. Thermostatically controlled cooler and 7 kW reservoir immersion heater.
-
Product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm With SPDT
50-293-122
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Databus-to-Network Interfaces
OBB2
Interface
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
Product
IEC61032 Test Probe 32
CX-32
-
Shenzhen Chuangxin Instruments Co., Ltd.
Test Probe 32 is intended to verify the protection provided by fan guards against access to hazardous mechanical parts.
-
Product
Conformance Calibration Standard Test Card for ISO/IEC Data Matrix and GS1 DataMatrix Symbol Verifiers
AI-CCS-DM-G Rev A
-
This precision 2D barcode Conformance Calibration Standard Test Card is the first 2D test card to provide ALL 12 of the Primary Reference Symbols specified by ISO 15426-2 for barcode verifiers. They are sized from 0.5mm to 0.2mm so that all the symbol sizes specified in Annex A.3.1 can be tested. Symbols 1-4 are GS1 DataMatrix symbols, while symbols 5-12 are ISO/IEC Data Matrix symbols consistent with the ISO/IEC 16022 standard. The card also includes four calibrated reflectance patches.
-
Product
PXI Resistor Module 2-Channel 1.5R to 1.02k with SPDT
40-293-121
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Installation Testers
-
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
