Verifiers
-
Product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
-
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
IC Pick & Place Handlers
-
Chroma's IC test and handler solutions assure that IC packaging meets the original design specifications and verify the performance of the IC before it is assembled into the electronic product.
-
Product
MIMIC sFlow Simulator
-
MIMIC sFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
Wire & Cable Testers
-
Precision Mastech Enterprises Co.
Diagnostic tools designed to verify electrical connectivity, map wiring configurations, and detect faults.
-
Product
Case Depth Hardness Tester
HTD-4000
-
HTD 4000 is used to measure case depth and is capable of verifying case depths ranging from 0.4mm (16 thou) up to a maximum of 2.5 / 2.8mm (100110 thou). Our system utilizes a new and very advanced principle based on the continuous measurement of the electrical resistance in relation to the working load applied. Our design meets the demands of the heat treatment industry. HTD 4000 is equipped with a big stand to enable the testing of large work pieces having overall dimensions up to 550mm (22") in height and 350mm (13.8") depth
-
Product
Sensors And Process Analyzers
-
Process analyzers as inline and online measurement technologies provide real-time data for outstanding process control, which results in high-quality production. Thorough monitoring by process analyzers with up to 100% coverage of process parameters and subsequent documentation ensures optimal compliance. Moreover, monitoring makes transactions verifiable and establishes a basis of trust between suppliers and customers.
-
Product
External Pacemaker Analyzer
EXPMT 2000
-
The EXPMT 2000 External Pacemaker Analyzer tests and verifies all the functions of any external pacemaker including transvenous, transcutanious (transthoracic), and Atrial and Ventricular sequential pacemakers.
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R with SPDT
40-293-111
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm
40-294-033
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Vacuum Tester
QCT-2A
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to vacuum cleaner type motor. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
Product
PXI Resistor Module 2-Channel 2R to 65.5k with SPDT
40-293-133
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm
40-294-012
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
DDR4 Parametric Test Reference Solution
-
Keysight's DDR4 parametric test reference solution helps verify the signal integrity of DDR4 memory designs according to JEDEC specifications.
-
Product
Phase Sequence and Motor Rotation Tester
PRM-6
-
The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads.
-
Product
Phosphorus CoatingColor Checker
-
West Coast Custom Designs, LLC
*Check and verify the color of phosphoresce coating on raw sticks of neon tubing.*Hold up to the end of phosphorus coated tubes and turn on, will show color.*Built-in safety features.*Hand held and portable. *Small and compact. Folds for easy storage.*Power tester from four AAA batteries - not Included.*Power tester with included Macro USB cord - not for charging batteries.*One Year Limited Warranty. *No Returns - All Sales Final.
-
Product
Signal Generator
MX-RFSG1800
-
The Maxcom MX-RFSG1800 signal generator is a simple low-cost device used to inject RF signals up to 1800 MHz into RF plant for the purpose of verifying those high frequencies are able to properly pass-through cables, passive and active devices.
-
Product
DOI / Haze Meter
807
-
TRICOR’s Hazer Meter and DOI is ideally suited for measuring flat, non-textured high reflectance surfaces. The Model 807A Haze Meter design is in accordance with ASTM E430 and ASTM D5767 (method A) and is used to measure ±3 degrees around the specular lobe centered at 30 degrees in approximately 220 increments. That’s an angular sample size of 1 sample per 1.6 minutes of arc! This allows differentiation between samples with very small differences in reflectance characteristics. Verified replacement for the older Hunter Dorigon II haze meter unit.
-
Product
Inline Barcode Verifiers
DataMan 475V Series
-
Cognex barcode verification technology ensures the readability and compliance of 1D and 2D barcodes to industry standardization guidelines. Today most companies spot check codes one at a time using an offline, operator-based verifier which can be slow and cumbersome.
-
Product
Microswitch, G12, Receiver, Left side
310113210
Microswitch
Microswitch, G12, Receiver, Left sidePlease note: Some G12 receivers already include a right or left side microswitch at the time of purchase, making purchasing this switch necessary only for replacement purposes. Check your G12 model number at purchase to verify.
-
Product
Reelsurance
LCi-18 RFID
-
Reelsurance LCi-18 RFID Label Counting and Inspection System with Tagsurance verifies the tag operation sensitivity using communications tests at several frequency and power level combinations with high resolution, stability and high speed. The system provides also accurate label counting, missing label detection and label dispensing of required quantities.
-
Product
Surface Quality Monitors
-
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable of validating the cleaning quality of all the part cleaning equipment available in the market. Any of SQM model series is capable of verifying metal contamination; monitoring absence/presence of organic and/or inorganic on virtually on surfaces of all metals. They are, price/performance, the most sufficient product available for testing surface of metals for surface cleanliness. These systems operate in an ambient environment, require no sample preparation or deposit of any agents on the surface. In any parts cleaning environment where the quality and efficiency of part cleaning equipment for removal of surface contamination is highly desired, these systems provide a scientific solution by quantitatively measuring the surface cleanliness. The SQM series has the sensitivity and operational simplicity required to provide fast and cost effective surface evaluation for all metals.
-
Product
High Voltage Breakdown Test Sets
HT-Series
-
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
Product
GPS/FMS Universal Test Fixture
TA-3000
-
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
Product
Shock & Drop Testing
-
Shock testing is often performed as part of a hardware qualification or design process. Information obtained during shock testing can improve the survivability of products as well as verify that they will perform properly in service. These types of tests require special transducers and measurement systems to record and process the high level, high frequency response.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm
50-293-024
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Calibration Executive Software
CalEasy Series
-
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
Product
DDR5 Logic Analyzer
FS2602
-
The FS2602 is our the latest logic analyzer probe used to test DDR5 SO-DIMM memory. It is designed to work exclusively with 4 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR5 SO-DIMMs running at ~4000MT/s.
-
Product
DIMM Interposer Probe
FS2361
-
The FS2361 is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154/64 Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 DIMMs.
