Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
-
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Safety Liquid Leak Sensor [Control Category 4PLE SIL3]
SQ4 Series
-
Panasonic Industrial Devices Sales Company of America
The SQ4 Series Safety Liquid Leak Sensor detect leaks and curbs danger resulting from them.The two-part design, consisting of the Sensor and the mounting bracket, simplifies installation. The Sensor itself incorporates a two-stage detection. The detection unit at the front of the Sensor issues a warning if it comes into contact with liquid, and the detection unit in the center of the Sensor initiates an emergency stop if it becomes immersed in liquid.To provide utmost flexibility, a chemically resistant version is also available. Up to 4 Safety Liquid Leak Sensors can be connected to the SQ4-C11 Controller.
-
Product
Service
-
KLA Instruments™ is committed to supporting our customers everywhere, throughout the life of their KLA products. Our lab tools offer focused support by product group, and our fab tools leverage KLA’s global services and support organization. With your tools’ UTID ready, please contact us using the information below, organized by product group.
-
Product
K Thermocouple Magnetic Contact Probe
TP757
-
Magnetic thermocouple type “K” probe for measurements on magnetic metal surfaces.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Thickness Gauges for Plastic films & Paper
CHY-CA
-
CHY-CA is a highly precise thickness gauge with mechanical contact method, which can be used to measure the thickness of films, sheeting, paper, corrugated paperboard, textiles, non-woven fabrics, and solid insulation materials, etc.
-
Product
Dimensional Inspection (3D Inspection)
-
The 3D measurement data from our scanners and PCMMs offers a comprehensive definition of a physical object that is used for measurement, inspection, comparison and reporting. When a part is defined by millions of points, you can see subtle deviations, slight variations and fine details, which gives you the confidence that a part (or mold) meets your specifications. To deliver the best of both worlds, we combine 3D scanning with our contact, touch-probe measurement tools to deliver precise dimensions on geometric shapes.
-
Product
Temperature Switch
T150D
-
The T150D Adjustable Stainless Steel Miniature Temperature Switches provide the end-user with a wide range of functionality without impacting durability. The T150 is designed for use up to 510°F but can withstand temperatures up to 800°F while still protecting the set point and life of the switch. The limit filled, saturated vapor sensor is in direct contact with the temperature-sensing outer shell producing fast response and accurate temperature control. The external setting scale provides full range adjustment and the external lock screw allows for easy adjustment of set point.
-
-
Product
Protective Cover, 9075, ITA
410112573
-
The ITA Protective cover is made of aluminum making it very rigid to protect your contacts and modules when the ITA is not in use.
-
Product
Custom Solutions
SYSTEM 8 Custom
-
ABI Electronics offers a range of solutions to cover the most common test combinations. Including both analogue and digital test techniques, they provide an excellent starter package for a wide range of applications. Note that any combination of SYSTEM 8 modules is possible - do not hesitate to contact a member of the sales team to discuss your requirements.
-
Product
Physical Contact Connectors
-
Amphenol Fiber Systems International
Physical Contact (PC) connections are characterized by the physical mating of two optical fibers. Precision ceramic ferrules are typically utilized for PC connections. A PC connection is accomplished by terminating the optical fiber into a precision ceramic ferrule. Epoxy is used to affix the fiber into the ferrule. The tip of the ceramic ferrule is polished in a precise manner to ensure that light enters and exits at a known trajectory with little scattering or optical loss. Polishing the terminated ceramic ferrule is a critical process in Physical Contact fiber optic connectors.
-
Product
Standard-Res Spectroradiometer
FieldSpec 4 Standard-Res
-
Analytical Spectral Devices, Inc.
The FieldSpec 4 Standard-Res portable spectroradiometer is the right choice for a wide range of remote sensing applications, including multispectral sensor ground truthing and calibration, agricultural analysis, and snow and ice studies. In addition to being a world class spectroradiometer, the FieldSpec 4 Standard-Res is equally suited to serve as a rugged, portable spectrometer for accurate contact reflectance
-
Product
Portable Digital Manometer
PS309
-
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
Product
Rotation Meters
-
Here you will find many types of rotation meter. There are different ways of measuring revolutions within the industrial sector, either optically or mechanically. The PCE-151 handheld series of rotation meter with Rotation Meter OverviewRS-232 interface can measure revolutions and velocity and store the readings onto a computer using software which comes with the device. The handheld digital rotation meter is ideal for measuring velocity and revolutions in research and maintenance. The PCE-T236 rotation meter measures velocity both by contact and non-contact and is good value for money.Non-contact measurement of velocity is done with the help of reflective tape. For a device that can be installed for measurements over a period of time, we recommend the PAX I rotation meter.
-
Product
Temperature Measuring Instruments
-
– Contact and ambient temperature measurement– Infrared temperature measurement
-
Product
20-Pin GMCT Female Connector, 10A, With Backshell
40-960-020-10A-F
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Also included is the backshell with screwlocks and cable clamp.
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, 26-28 AWG
610110169
-
Primary mating contact 610110167. (May mate with other Receiver contacts, as well.)
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS Basic
-
Optik Elektronik Gerätetechnik GmbH
Low cost contact angle meter provides all functions for DIN conform measurement of contact angle and SFE.
-
Product
Plugbord
3662
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only.Unrestricted component placement over entire board surface
-
Product
Capacitive H.V. Detectors (Contact)
213 HVD~226 HVD
-
Standard Electric Works Co., Ltd
Excellent shock resistance. Rugged nylon moulding. Auto on (when voltage detected). Excellent drop resistance. Good vibration resistance. Loud sound alarm indication. Built-in proving and self-test circuit. High bright color-coded LEDS. Works from standard 9V battery. Interchangeable contact electrode. Use in all whether conditions. Compatible with all link sticks. Lightweight, robust & compact. Models available from 11kV to 132kV. Suitable for indoor and outdoor use. Self(auto on) or manual arming. Easy access to batteries. Customized threshold on demand. Auto off (if no voltage detected). Waterproof design, protection class : IP65.
-
Product
Test Fixtures-Assemblies
-
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
Product
TSN/PTP Partner Test Tools
-
The following test and measurement tools are available for members within our IEEE 1588/PTP, Avnu, and TSN Testing services. We would like to thank all of our partner companies for allowing members the opportunity to test against their products in one lab. If you have additional testing needs please contact us today.
-
Product
Receiver, D16, 16 Modules, 90 Series Modules
310131111
-
The D16 receiver frame accepts sixteen 90 Series modules and can engage up to 3,840 signal contacts.
-
Product
Handheld Tachometers
-
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
Product
Needle Microprobe
MT-23/3HT
-
Fast-response 23 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
-
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
Product
Relay Modules
U70000/URS70000/E70000
-
Universal Switching Corporation
Our relay modules are available with various contact configurations, connector types, sizes from 1x2 to 1x24 ports, and three different control types. The frequency range is from DC to 800MHz (size Dependant) and has many other options you can specify to meet your requirement.
-
Product
Laser Diode
-
Is a Polarization Maintaining CWDM Coaxial DFB-LD for CWDM analog communication, CATV return-path, laboratory instrument, and R&D applications. This cost-effective, high reliability DFB laser chip has a selectable wavelength with range between 1270 nm to 1610 nm. The versatile DFB-CWDM also features a built-in InGaAsP monitor photodiode, built-in optical isolator and 4-pin coaxial- pigtailed package, single mode coupling, and an FC/APC connector. Contact Optilab for more information.
