-
Product
Framegrabber
FastXe2
-
The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus
-
Product
Single Board Computers
SBC35-C398Q-2-0
-
WINSYSTEMS’ SBC35-C398Q quad-core single board computer combines high-performance multimedia graphics with a rich mix of industrial I/O. The Freescale i.MX 6Q processor’s integrated power management provides excellent efficiency and allows operation from -40° to +85°C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
Product
SparkFun Qwiic Single Relay
-
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!
-
Product
Electronic Contract Manufacturing
-
Specializing in low-mid volume electronic manufacturing services, Pine Electronics, Inc. offers a wide range of printed circuit board assembly (PCB assembly), cable and box build assembly solutions. Our equipment, engineering and technical talent serves both multi-national and regional customers throughout the United States. Known for full-service PCB assembly work, Pine Electronics, Inc. is highly integrated and responsive. Each customer has a designated representative for all commercial and technical questions. This personalized service model enhances communication, expedites project development, and represents Pine’s commitment to customer service.
-
Product
Framegrabber
FastX1703
-
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
Product
Dual/Quad Display Controller Board
BL-PXQ524-01
-
The MicroImage PXQ524 is a true high performance quad display controller designed for demanding applications. In addition to the quad display, the unit will also display two full images side-by-side unlike split screen, which only shows a portion of each image. The two images may be easily exchanged with a front panel switch. The side by side display works well with wide screen monitors where the additional black at the top and bottom isn’t as visible, maximizing display use. The MicroImage Video Systems Quad Display controller has been designed for industrial and professional applications. Operation is simplified with easy to use buttons to control commonly used functions rather than having to waste time in deep menus for common functions.
-
Product
VITA 48.4 Liquid Flow-Through (LFT) ATR Platform
VITA 48.4 LFT ATR
-
Elma Electronic’s rugged OpenVPX ATR platform is designed to accommodate boards requiring liquid flow-through (LFT) cooling per the VITA 48.4 standard. VITA 48.4 modules are cooled by liquid flowing through an integral heatsink.
-
Product
ASA200
-
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
ARM LPC3250 Board
MS 1509
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
Backplane Twinax Connectors
-
We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.
-
Product
DAQ User Interface Software
DAPstudio 3.00
-
If you need to deliver a data acquisition system quickly and you want to develop a good user interface for it, then download DAPstudio 3.00 and see how that could help. You now can use the latest (full) version of DAP Measurement Studio software from Microstar Laboratories, maker of Data Acquisition Processor (DAP) boards and software, for an unlimited trial period at no charge.
-
Product
Single Board Computers
-
At the heart of every system is the single board computer. Elma sells, supports and integrates the latest in Intel and Freescale based single board computers from industry leading partners including Artesyn Embedded Computing, Concurrent Technologies, GE-IP and Interface Concept, as well as a few other specialized boards. When integrated as one of our popular AppliPaks, the SBC becomes part of a tech refresh solution which includes operating system and driver integration, plus mezzanine I/O or storage to form a bundled assembly sold and supported by Elma.
-
Product
16 channel 16 bit Digital to Analog Module
CPCI-DA16-2
-
The CPCI-DA16 is a slave Digital to Analog board thatis managed by the host processor on the CPCI bus.The card contains a state machine that performs mostof the work of outputting data, in order to minimize theimpact to the HOST system.
-
Product
3.5" Single Board Computer
RSB-4710
-
RSB-4710 is a RISC 3.5" single board computer (SBC) powered by a high-performance Rockchip RK3399 ARM dual Cortex-A72 and quad Cortex-A53 high performance processor which supports 4K display from HDMI. It offers both multiple display as dual HDMI/LVDS/eDP and multiple IO as dual GbE/6 x serials/6 x USB/5 x GPIO. RSB-4710 also features Mini-PCIe, M.2, and SIM card slots for integrating Wi-Fi, Bluetooth, and 3G/4G modules. It is an ideal solution for Kiosk, POS, and Vending machine application.
-
Product
IP-Parallel-BA1 "IP-Tape"
-
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
Product
SparkFun RGB Light Sensor
ISL29125
-
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity of the general red, green, and blue spectrums of visible light while rejecting IR from light sources. You can then use these color sensor readings for the purposes of logging and finding patterns, or creatively calculate and make control decisions in your electronic projects.
-
Product
3.4 MP Autofocus Low Light USB Camera Board With Liquid Lens
See3CAM_30
-
See3CAM_30 is a 3.4MP UVC Compliant, low light, autofocus USB camera with liquid lens. It is a two-board solution with AR0330 CMOS image sensor from ON Semiconductor and USB 3.1 Gen1 type C interface board. See3CAM_30 is a colour camera with S-mount lens holder and does not require any special camera drivers to be installed in the host PC. See3CAM_30 is customizable and it is a Ready-to-Manufacture camera with all the necessary firmware built in and compatible with the USB Video Class (UVC). It consumes less power and doesn't heat up. There is no mechanical movement like in VCM motor for autofocus. Hence the life of the lens increases.
-
Product
Digital Vision Microscopes
-
Sinowon Innovation Metrology Manufacture Ltd.
Video Microscope is widely used in the inspection of electronic industry production line, printed circuit board, weld detects ( such as wrong printing, edge collapse,etc)during printed circuit component, PC Board, VFD, and the identification of printing grid and painting, etc. It can display the zoom out image on the screen and save, magnify and print.
-
Product
3U CompactPCI Serial Power Interface Board
046-201
-
Standalone Power-BP 3U 8HP to connect CPCI Serial power supplies to compactPCI Serial-BPs. The connection is made via cables.
-
Product
Universal AC-DC Power Supplies
PS-WT24-12-US
-
The PS-WT24-12-US is a small, convection cooled, 24W wall wart power supply for use with WINSYSTEMS’ embedded computer systems. The unit can be used as a power source for single board computers, industrial computers, or low power Panel PCs. It is a universal design that accepts 90 to 264VAC input and generates up to 0.5A of current at +48 volts.
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Modulator Driver
-
A compact bias control board designed to maintain the linear operating point of optical intensity modulators. Featuring a compact miniature design for OEM integration, the BCB-4 allows for a stable Q+, Q-, Min and Max operation over long periods of time. With a USB 2.0 DC power and monitor interface standard, the BCB-4 unit is the ideal choice for industrial and OEM applications when paired with any of Optilab’s wide variety of optical modulators. Please contact us at +1(480)719-1502 or email sales@oequest.com for more info.
-
Product
FMC L-Band RF Receiver
-
Sundance Multiprocessor Technology Ltd.
The Creonic L-band RF receiver FMC card allows to receive RF signals between 925 and 2,250 MHz. It is ideally suited for satellite communication with standard satellite dishes since it includes a DiSEqC driver IC for LNB controlling. The board allows to build receivers with symbol rates of up to 100 Msymbols/s. Due to the low-pin-count (LPC) FMC connector it can be used with any FMC carrier board that supports VADJ=1.8V. The card will be available from Q2/2017.
-
Product
System Accessories
-
To support the full need of the application Elma offers a comprehensive range of system level accessories to include: I/O solutions, HMI Displays, System/Power Management, Test/Development Boards, and Mechanical Mounting products.
-
Product
Functional Test Fixtures
-
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
Product
CPCIe (PXIe) Module
ACS-FC-3U-2
-
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
-
Product
GPU-Oriented x1 PCIe 3-Way Splitter
SKU-040-43
-
The Flexible x1 PCI Express 3-Way Splitter was designed to expand your modern motherboard (ATX, mini ATX, etc.) with limited PCI Express slots. It allows you to connect up to three x16 PCI Express add-in boards, such as GPUs, to your motherboard’s x1/x4/x8/x16 PCI Express connector.The Splitter includes three x16 PCI Express adapter boards with PCI Express flat cables, and one x1 PCI Express host board.
-
Product
PMC Dual Channel MIL1553B Board
MS 1722
-
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- 553B controller based design- 2 dual redundant channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
Product
Group3 Control
-
Group3 Control is a fiber optically linked control system using distributed I/O modules called Device Interfaces, or DIs. A DI is positioned at the point to be controlled and the appropriate I/O boards added to it from the list below.
-
Product
224 Channel Digital I/O Modular PXI Card
GX5731
-
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
