-
Product
Timing Board #1
TIO-10 #1
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. Bursts, delayed pulses, and frequencies can be generated on outputs. The input channel can be used to measure frequency or period.
-
Product
Acquisition Of 16 Displacement Transducers
APCI-3701-16
-
PCI interface to the 32-bit data bus Acquisition of 16 inductive displacement transducers (Half Bridge, LVDT) 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
Product
Carrier Board for Hilscher Fieldbus
SF1-STUDIO
-
SF1-STUDIO is optimized for Hilscher real-time Ethernet & fieldbus modules. Many popular protocols are supported. Ethernet, mezzanine modules are available for EtherCAT, EtherNet/IP, Open-Modbus/TCP, POWERLINK, PROFINET IO, Sercos, and VARAN.
-
Product
Fastest In-Circuit Test Platform
TestStation
-
Teradyne’s TestStation in-circuit test systems provide electronics manufacturers with reliable high-quality, high-volume testing for the latest printed circuit board assembly (PCBA) technologies that are used in automotive, industrial, computing, consumer, communications, and defense end-products.
-
Product
SparkFun Breadboard Power Supply Stick
3.3V/1.8V
-
This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
Product
PCI Embedded Cables
-
Acromag provides a large selection of signal cables to complete the connection of the field wiring on the termination panel to the I/O board. We offer you a wide assortment of ribbon cables to accommodate the various pin and connector configurations.
-
Product
Advanced 4-Axis Servo & Stepper Motion Controller with Modular Design
PCIe-8154
-
The PCIe-8154 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8154 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8154 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5923-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
SBC
PPC11A
-
The PPC11A supports the same technology insertion pin-out as previous members of the PowerXtreme family including popular boards such as the PPC4A, PPC7A, PPC9A and PPC10A, minimizing integration time and effort for legacy upgrades.
-
Product
SKYbolt II 9U VME
-
Delivering 64 GFLOPS of performance when fully populated, the SKYbolt II 9U VME motherboard is the foundation of SKY's VME solution, adding intelligent support for system services and high-performance data transfers to the carrier board for SKY's Merlin daughtercard containing compute processors, I/O interfaces, and global memory. A separate System Processor resident on the motherboard handles system overhead functions that would otherwise burden the compute processors.
-
Product
Heavy Board & Heavy Board
Protector Lever Actuated Clamshell
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
CARB Testing
-
Underwriters Laboratories Inc.
The ASTM D6007 (small chamber) and ASTM E1333 (large chamber) test methods are used by the composite wood products industry to measure emissions of formaldehyde from plywood, particle board and medium-density fiberboard (MDF), commonly known as CARB testing. Testing is conducted in environmental chambers operated at defined product loading, temperature and relative humidity.
-
Product
Ultra Compact PC-Based EtherCAT Controller With Intel Atom Processor, 64GB EMMC, 2 X LAN, 2 X USB And Slice IO Expansion
AMAX-357
-
Up to 32-axis EtherCAT PC-based motion controllerIntel® Atom® quad-core x6413E processor4 GB DDR4 onboard memory64GB eMMC on board storage2 x GbE LAN, 2 x USB, 1 x HDMI, 1 x EtherCATFull-size mPCIE/mSATA for flexible expansionBuilt-in TPM2.0 for hardware-based securitySupports PTP, linear and circle interpolation, Path tableSupports C/C++, VS.Net, LabVIEW programming languages
-
Product
Rebound Hammer
Schmidt OS-120PM
-
The Schmidt OS-120 Pendulum Hammers are designed to test on softer material such as light weight concrete, gypsum boards, fresh concrete and the mortar of joints in brickwork. Their unique design allows easy to handle measurements on vertical and horizontal surfaces.
-
Product
Hardware Debugger for the Raspberry Pi
TAP-HAT
-
The TAP-HAT is a low-cost hardware debugger for the Raspberry Pi®. Its flexible multi-modal design supports USB-connected hardware debugging of a Pi board, connection of external hardware debuggers to a Pi, or use of the Pi as a network attached hardware debugger.
-
Product
PCIe 4.0 Protocol Analyzer
Summit T48
-
Teledyne LeCroy’s Summit™ T48 joins the Summit™ T416 as the second protocol analyzer to be released in its family of tools supporting the PCIe 4.0 architecture. The new Summit™ T48 protocol analyzer based on the PCIe 4.0 specification supports up to 16GT/s and up to x8 lane width for protocol analysis. Companies that are interested in testing PCIe 4.0 based I/O cards such as Storage Controllers, Ethernet, Fibre Channel, Infiniband, and others will now be able to get all of the protocol analyzer debugging features they need, while being able to better manage their costs. SSD storage applications will also benefit from the integrated support for SSD bus protocols such as PCIe/ NVMe/ SMBus/ NVMe-MI/ TCG and others. When combined with Teledyne LeCroy’s Summit™ Z416 protocol exerciser, the Summit™ T48 will provide a deeper understanding of test results on a variety of test configurations. Teledyne LeCroy’s wide range of high speed interposers and probes provide full flexibility and connectivity to CEM and other form factor sockets on system boards as well as solder down and mid-bus probes.
-
Product
MOTUS Stand-Alone Sensor
-
There are numerous ways of measuring Ocean Waves. At Aanderaa, we focus on three measurement types: pressure, acoustic, and motion. In this section, we cover the motion-based sensors in the MOTUS family.MOTUS Directional Wave Sensor is suitable for integration on different buoy types. It is intended for commercial as well as research use. The directional stand-alone Sensor processes wave data and is configurable to directly present parameters and wave spectrum. The sensor can be connected to a SmartGuard using the CANbus-based AiCaP protocol. It can also be connected to a PC or third-party systems through the RS-232 interface.MOTUS Wave Height Sensor is for wave height only. As the MOTUS Directional Sensor, it is suitable for integration on different buoy types. In the sensor, the directional wave parameters are locked. It is possible to open the wave direction parameters with a software license from Aanderaa later if the need changes. MOTUS Lite OEM Sensor is the OEM version of the MOTUS Directional Wave sensor. It is delivered as an electronic board without housing and cables. Please get in touch with the factory for more options and restrictions.
-
Product
EDA Software
-
Shorten design cycles to achieve first-pass design success. Our next-generation integrated electronic design automation (EDA) software provides engineers with new tools and enhancements to bring efficiencies into their printed circuit board (PCB), RF and microwave, 5G / 6G, and high-speed digital design flows.
-
Product
Breakout Boxes
D Series
-
The D Series Breakout Boxes incorporate a printed circuit board for all connectivity. D Series Breakout Boxes use a color coding scheme as an aid. The Red jacks connect to the Red TP Side connector with pin contacts and the Black jacks connect to the Black TP Side connector with socket contacts.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
PCI Multifunction Board
PCI-1800HU/S (includes CA-3710 cable)
-
The PCI-1800/1802 (L/H) is a family of high performance data acquisition board with 5V PCI bus. The PCI-1800/1802LU/HU card has a universal PCI interface supporting both 3.3 V and 5 V PCI bus. All the members in the PCI-1800 family have the same architecture; they feature a continuous A/D acquisition function of up to 330 kHz for low gain (44 kHz for high gain) under DOS and offer two 12-bit D/A output channels, 16 digital input channels and 16 digital output channels. The PCI-1800 series provides 16 single-ended or 8 differential inputs while the PCI-1802 series provides 32 single-ended or 16 differential inputs. In addition, an amazing A/D channel scan function called “MagicScan” is provided for users to easily implement multi-channel analog data acquisition applications. The specific MagicScan controller takes out most works of getting A/D value such as selecting channel, setting gain, settling time, triggering ADC and getting data. Even in channel scan mode, it can have different gain code for each channel, and the sampling rate can still reach 330 kS/s totally. The PCI-1800 series is suitable for high end applications.
-
Product
Test Engineering Projects
-
Precision Development Consulting Inc
Fiber Optics Test System, Data Collection, Trident Missle Components, PC Board Functional Test and Bearing Tester
-
Product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
-
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PICMG 1.3 single board computer has a maximum of six SATA-600 ports supporting software RAID 0/1/5/10 for data redundancy. It also has one M.2 Key M 2280 SSD slot with a PCIe x4 interface. The SHB150 with the Intel® HD Graphics brings a true high definition visual experience with triple display configurations (Intel® C246 or Q370) via DVI-I and DisplayPort (header) ports. Moreover, the Intel® Coffee Lake-based SHB150 supports optional Trusted Platform Module (TPM) 2.0 for optimum security, Intel® Active Management Technology (Intel® AMT) 12 for remote management, as well as Intel® vPro™ technology. The industrial single board computer provides significant advantages to customers in the fields of machine vision and industrial automation operations
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
-
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
Computer On Modules
COM Express Mini
-
Advantech COM Express Mini series boards includes Intel Core i, Intel 4th Generation, Intel Atom processor. With mere 84 x 55 mm in size, COM Mini series are the most compact COM modules and match all demands from Intel Core i, Intel 4th Generation, to Intel atom processor. COM Express Mini series is compliant with the COM Express Type 1/10 standard pin definition, and with a slight modification are able to commit with the existing COM Express carrier boards.
-
Product
MIL-STD-1553 Four-Channel VME Board
BRD1553VME-4
-
The V-Orchestra™ is a four channel MIL-STD-1553B board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 64K word of internal RAM.
-
Product
12 Bit Waveform Digitizer Board
ATS9352
-
With data throughput as fast as 1.6 GB/s (1600 MB/s), ATS9352 is an ideal solution for many applications, including OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
Product
3U VPX Processor Card
VPX3-1260
-
Curtiss-Wright Defense Solutions
Optimal for high performance embedded computing (HPEC), general processing, and a variety of C5ISR applications, the VPX3-1260 rugged single board computer (SBC) delivers a fully-featured, all-in-one processing solution for your embedded system.
-
Product
Eurocard Plugbord
4614-4
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides Voltage and ground bus around board perimeter on both sides For solder, Wire-Wrap or mixed wiring methods Pad and bus surfaces solder-coated for user convenience Row and column legends provided
-
Product
Circbord
8019-1
-
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
