Signaling Testers
-
Product
1HZ~100MHZ Crystal Oscillator Tester
CX-118A
-
Shenzhen Chuangxin Instruments Co., Ltd.
1 It's using reciprocal counting technique, high accuracy, wide measuring range, truly equal precision measurement, fast speed measurement, high sensitivity.2 single-chip microprocessor technology cycle frequency measurement and intelligent management, making the instrument has high reliability and excellent performance / price ratio.3 It's using LSI design, the use of CPLD devices, instrument components greatly reduced, reliability has been greatly improved, the average time between failures ≥10000h.The machine looks nice, small size, light weight, easy to use.
-
Product
Safety Footwear Impact Tester
SG-P11A
-
This machine, incorporating a steel striker adaptered to fall freely on vertical guides from a predetermined height to give the required impact energy to the toe of safety footwear for measuring the degree of the dent. In addition, the toecap should not develop any cracks on the test axis with go through the material.
-
Product
SOC Battery Tester
-
This sophisticated battery test equipment allows the battery tester to exercise and explore the battery’s internal profile and produce a true state of charge revealing the batteries true AHR capacity and ability to perform under load.
-
Product
LATCH UP Tester
-
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
Product
Scorch Tester (Sublimation Fastness Tester)
TF415D
-
TESTEX Testing Equipment Systems Ltd.
Scorch Tester, to determine fabrics Ironing color fastness and sublimation color fastness, and dimensional stability under hot dry conditions. Sublimation Fastness Tester complies with ISO 105, BS 1006, AATCC 92/114/117/133. Sublimation machine price is reasonable.
-
Product
Contunuity Tester With Audio Warning
CT-01
-
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Graduall
-
-
Product
Torque Tester
DI-4B-25
-
For daily inspection of small impact tools. Since the display uses an LED, the numbers can be read clearly even in dark places
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
-
Product
Medical Masks Differential Pressure Tester
-
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
Product
CDM testers
Scorpion
-
Scorpion opens a new generation of CDM testers. It is designed to meet the new JS-002 standard and features Contact First pulse delivery. This patent pending technique of Contact CDM (CCDM) meets the latest CDM standards with higher accuracy for device classification.
-
Product
350 MHz DDS Signal Generator
425A
-
The 425A generates sine, LVDS and LVCMOS outputs simultaneously and is programmable in 10µHz steps from 250kHz to 350MHz and includes an LVCMOS Prescaler and Divider for generating LVCMOS frequencies down to 2 Hz. The 425A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. A Line Voltage AC Adapter is included. SOF8_425 windows software is also included.
-
Product
Hand-Held/Digital Load Tester
6030
-
• Full 125 Amp load tests 12 Volt batteries, alternators and starters on all type of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
Fluorescent Lamp Asymmetric Pulse Tester
UI2002C
-
UI2002C is designed according to the latest update in IEC 61347-2-3 about the test requirements for local rectifying effects on tubes. It imitates the condition when tube is under local rectifying status and tests the abnormal protection function of ballast by adopting fluorescent lamp asymmetry pulse test method with 3 windows for displaying rectified voltage, rectified current, and rectified power. It is easy for operation and with high test accuracy. • Measure lamp voltage, lamp current , average and total power of lamp. • Lamp voltage range: 10~300V • Lamp current range: 10mA~1.0A • Lamp power range: 0.5~300W • Tolerance is 5%
-
Product
WAN Tester II
-
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
Product
Signal Integrity Evaluation up to 50 GHz
N5225BT
Network Analyzer
The N5225BT provides the N5225B 50 GHz PNA, application software including PLTS and Enhanced TDR and accessories for signal integrity evaluation of cables, backplanes, and BGA packages.
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
Digital And Mixed Signal Oscilloscope
MSO/DPO70000 Series
-
The MSO/DPO70000 is one of the most advanced oscilloscopes in its class: enabling today’s engineer to see signals better with minimal noise, debug signal anomalies faster, reduce debug time, and utilize measurement and analysis tools for automated compliance testing and other verifications. In addition, the MSO/DPO70000 is perfect for analog/digital design and debug, data communications and high-speed serial communications. See how you can use the MSO/DPO70000 for your next project to find and analyze a wide range of mixed-signal anomalies.
-
Product
Compact, Easy To Use Tester.
Eye-BERT 40G
-
The Eye-BERT 40G packs 40Gbps of test capability and a color touch screen into a compact, easy to use tester. The Eye-BERT 40G offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of QSFP transceivers as well as link verification and performance testing all in a single unit. The automated QSFP test feature also allows the user to quickly verify transceiver performance and automatically generate a report complete with unit serial number.
-
Product
Automated Tester
-
With high labor costs in Europe and the US, and the surge in labor cost in Asia, automated test solutions are in demand. Automated systems also improve traceability and reduce operator mistakes.The combination of automation with high throughput test systems is perfect to extend the usage of Flying Probe Testers to mid size production/sample volumes.
-
Product
Reach Power-over-Ethernet (PoE) Testers
-
After assembly, electronic equipment manufacturers need to test functionally of their products. They want to provide the most test coverage, in the shortest time, for the least cost. When test engineers develop product test plans, they select the most appropriate off-the-shelf general purpose test equipment available. Reach designs and manufactures custom test equipment which is a better fit than general purpose equipment. It not only reduces test time but also reduces costs.
-
Product
TAP Signal Isolation Module
JT 2139
-
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
Product
Drop Tester
AccuDrop 125
-
Model AD-125 is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
Product
Network Connectivity Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Clamping Voltage Tester
MIG0603CLV1
-
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
Product
LCM Panel Tester
27013
-
Chroma 27013 is a portable tester that supports high resolution and large scale LCM with the signals, power supply and test patterns required for LCD module test.
-
Product
VDSL Tester
X5008
-
X-5008 VDSL tester specially designed for slid line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL, VDSL2 etc) and maintenance It provides xDSL test, PPPoE dial test, DMM test, Modem emulation, line voltage indication and so on. X-5008 VDSL Tester also introduces the Optical Power Meter and Visual Fault Locator function into the unit, as well as the TDR function. It is one mufti-function tester with smart size, true color LCD and powerful management software as well as the 6600mAh rechargeable battery etc.
-
Product
Signal conditioning
-
Simple parameterization of the sensors and visualization of the measured values via the on-site display.
