PCI
The Peripheral Component Interconnect Bus is a standard for connecting peripherals to a PC.
See Also: Instrument Control Buses, Modular Instruments, PXI, PXIe, LXI, AXIe, PCIe, GPIB, USB, Ethernet, LAN, miniPCI, CompactPCI, PCI-X, PCI extended
-
Product
Pulse Pattern Generator, 3.35 GHz, single channel
81133A
Pulse Generator
The Keysight 81133A single-channel 3.35 GHz Pulse Pattern Generator is the latest product in the long history of Keysights high-speed Pulse Pattern Generators. When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. Like its predecessor, the Keysight 8133A, the new 81133A sets the standard for high-speed applications. The Keysight 81133A lets you test your DUT instead of the pulse or data source! For applications that require multiple output channels or multi-level signaling like pre- and de-emphasis (PCI Express) or squelch (Serial ATA), please refer to the 81134A.
-
Product
PCI card with 3 IP sites
PCI3IP
-
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
Product
Processor Intel Core I7, PCI Gen 3, AMC
AMC726
-
The AMC726 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® 4th generation Core i7 Processor (Haswell) with QM87 PCH. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
Product
x1 PCI Express System Timer
SKU-048-01
-
The x1 PCI Express System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The Timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the x1 PCI Express System Timer supports clock intervals ranging from 1ms to 64ms.
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
PCI Digital I/O
APC464
-
Four 16-bit multifunction counters/timers are configurable for pulse width modulated output, watchdog timer, event counter, frequency measurement, pulse width measurement, period measurement, or one shot pulse output. The four 16-bit counters can also be configured into two 32-bit counter/timers.
-
Product
PCI 2 Amp Multiplexer, Single 8-Channel, 4-Pole
50-635A-103
Multiplexer Module
The 50-635A-103 is a single 8-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI-5114 , 125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device, 8 MB
779745-01
Oscilloscope
125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device—The PCI‑5114 low-cost oscilloscope device has two channels that sample up to 250 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth.
-
Product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 2 Front Slots, Texas Instruments PCI1520 Chipset
P423B-TI1520
-
The PCI to 2-slot PCMCIA/CardBus PC-Card adapter supports 3.3V & 5V PC-cards (PCMCIA/Cardbus) simultaneously. Hot-swap PCMCIA/Cardbus PC-cards without powering off the system. 2 independent icons in MY COMPUTER. The adapter is quick & easy to install, allowing PC-card devices to be used in any desktop or tower PC.
-
Product
Digital Input/Output Cards
PCI-DIO Series 24 and 48
-
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers. The card is 6.9 inches (175 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
Product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, LAN, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s) And 2 PCIe Mini Card Slots
IRU152
-
The IRU152 is powered by the low-power NXP i.MX 6 UltraLite processer. It can withstand an extended operating temperature range of -40°C to +70°C and up to 2G of vibration for operating in harsh environments. Furthermore, it supports NI LabVIEW to allow users to design graphical user interfaces for their measurement applications quickly and efficiently. In order to provide data collection and device control, the IRU152 comes with various I/O connectors, including four analog input (AI) channels, one isolated RS-232/422/485 port, one isolated LAN and one isolated DIO (2-in/2-out). The four analog input channels have differential input configuration and overvoltage protection of 55V DC. The maximum sampling rate of IRU152 is up to 250 kS/s with a 16-bit resolution for low-speed high-resolution sensor monitoring and signal measurements. Apart from the abovementioned features, the IRU152 comes in two PCI Express Mini Card slots and one SIM card slot for Wi-Fi, 3G/4G and LoRa connections. The DIN-rail embedded system is equipped with onboard 512MB DDR3 SDRAM; besides, they have an 8GB eMMC flash memory. The extremely low power industrial IoT gateway has passed the Heavy Industrial certification and FCC part 15 to ensure the excellent quality and highly reliable performance.
-
Product
50 Ohm SMA to SMA Cable Assembly
40-977-521-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Flexible x1 PCI Express to 3 MiniPCI Splitter
SKU-070-XX
-
Flexible x1 PCI Express to 3 MiniPCI Splitter was designed to expand your modern motherboard (ATX, mini ATX etc.) that lacks a MiniPCI interface. It allows you to connect up to three 124-pin MiniPCI add-in boards to your motherboard’s standard PCI Express connector.Splitter includes 3 MiniPCI adapter boards, x1 PCI Express host board and 3 flat PCI Express cables.
-
Product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
XMC-to-PCI Express Adapter
4821
-
The XMC2PCE is a passive 8X XMC to PCI express carrier card which permits the use of XMC cards in PC style PCI express 1X, 2X, 4X, 8X or 16X motherboard slots.
-
Product
PCI Reed Relay Card, 64xSPDT
50-110B-121
Reed Relay
The 50-110B-121 is a 64xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI Single Channel Multi-Band Down Converter (ISA and VME Legacy Versions Available)
LS-25-D
-
Lumistar offers single PCI slot multi-band FM receivers. The same product in a “drive Bay” configuration is available. All Lumistar FM receivers can come without the FM demodulator use as antenna tracking receivers or for use as down converters used with an IF receiver for multi-mode digital combining and demodulation. Dual channel versions are also available.
-
Product
Expansion I/O Module.
SI-MOD66xx
-
The SI-MOD66xx is a family of high resolution, multi function data acquisition and control modules that plug into any SI-CxDSP carrier processor card for the PCI bus.
-
Product
50 Ohm SMB to SMB Cable Assembly
40-977-511-0.5m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
75 Ohm Mini SMB to BNC Adaptor Assembly
40-978-701-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 6.97kΩ
50-297-024
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
4 Port PCI Express
PEX 8604
-
The ExpressLane™ PEX 8604 device offers 4 PCI Express Gen 2 (5.0 GT/s) lanes, which supports up to four ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX8604 is the industry's smallest 4-lane Gen 2 device and it enables users with the ability to connect multiple PCI Express endpoints which are used in a variety of consumer and embedded applications including Multi-Function Printers, wireless ethernet modules, IO expansion modules, Express Card applications as well as other low power applications.
-
Product
PCI High Voltage MUX
50-350-001
Multiplexer Module
The 50-350-001 is a Short PCI Card designed as a high voltage multiplexer for use in a Submarine Cable Testing Application. It is designed to allow the dynamic connection of various test instruments to 1 of 16 test points. The multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.
-
Product
24-Port PCI Express
PEX 8796
-
The ExpressLane™ PEX8796 is a 96-lane, 24-port, PCIe Gen3 switch device developed on 40nm technology. PEX8796 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
XMC-to-PCI Express Adapter
7769
-
Our XMC-to-PCI Express Adapter 1X w/ VITA 61 (XMC 2.0) Style Connectors (7769) permits the use of a single-wide XMC module in a 1X PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector.
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
Interface Card
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
PCI BUS Interface Card
PCI301
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 2.97MΩ
50-297-051
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Mini-ITX SBC With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 Processor, Dual DisplayPort++, HDMI, LVDS, USB 3.0, MSATA, M.2 And Dual GbE LAN
MANO520
-
The MANO520 is powered by the LGA1151 socket 9th/8th generation Intel® Core™ i7/i5/i3 (code name: Coffee Lake), Intel® Pentium® Gold or Intel® Celeron® processor with the Intel® Q310 chipset (Intel® Q370 optional). The Intel® Coffee Lake-based MANO520 is specifically designed for performance-demanding applications with its excellent reliability as well as communication and real-time computing capabilities. The MANO520 supports two 260-pin DDR4-2666/2400 SO-DIMM sockets for up to 32GB of memory. Also, the mini-ITX motherboard features three SATA-600 connectors and one mSATA for additional storage. It is equipped with one full-size PCI Express Mini Card, one PCIe x16 and one M.2 Key E slots for wireless devices such as Wi-Fi, Bluetooth, and 3G/LTE. Moreover, the mini-ITX form factor single board computer features an ATX connector with AT mode auto power function.
-
Product
50 Ohm SMA to SMA Cable Assemblies - 3GHz
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
