Lighting
is used to illuminate.
See Also: Light, Illumination, Lightning, Lightwave, Daylight, Streetlight, Light Sources, DMX
-
Product
ITO (Indium Tin Oxide) Electrode
-
This quite unique material transmits only visible light whereas it does not transmit UV radiation. Our ITO electrodes consist of 100 nm thick of ITO layer deposited on quartz or borosilicate glass substrate (0.5 mm thick).
-
Product
Trailer Light Tester with Ammeter
Checkmate 1200-A
-
An improved version of the Checkmate 1200, this reasonably-priced tester comes equipped with a 0-to-20-amp ammeter. It's capable of testing SAE trailers or RV's with electric brakes.
-
Product
Compact Measurement System For Steel Wire And Rods With Small Diameters
-
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
Product
Light 0.75 (21.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-25T36-2
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Scintillator Detectors
SIGMA Family
-
Our SIGMA range of CsI(Tl) thallium activated caesium iodide scintillator radiation detector products replaces conventional photomultiplier technology with state of the art SiPMs. These gamma-ray detectors offer up to 32.8 cm3 of detection volume, delivered in a package providing significant benefits in cost, size, weight, power consumption and temperature stability. Robust, small and light SIGMA caesium iodide scintillator radiation detectors are perfect for radiation detection in the field and in the lab. Clients have flown them on drones, built them into large detector arrays and other devices. If you need fast detection in an easy to use package this is what you need.
-
Product
High Elongation Extensometers
Model 3800
-
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
Product
CORROSION GAUGE
MX-2
-
The MX-2 is ideal for the person that tests a few different materials regularly. The MX-2 contains 8 velocities of common materials and two velocities that the user can set using a simple sofware program. The tool's backlit display is easy to read, even in dim light, and the unit operates for up to 200 hours on a single set of batteries. The MX-2 comes complete, ready to use, and is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
LED Stroboscopes
-
Our LED stroboscopes use solid-state light sources that are very durable and long lived with no heat generation or drift over time. They feature push button control of all digital functions and pulse width modulation to ensure sharp images at high speeds and aluminum housings.
-
Product
Fully Automatic Colorimeter
DRK103C
-
Shandong Drick Instruments Co., Ltd.
(1)5 inch TFT color LCD touch screen, the operation is more humanized, new users can be mastered in a short period of time using the method.(2)Simulation of D65 lighting lighting, using CIE1964 complementary color system and CIE1976 (L*a*b*) color space color difference formula.(3)The motherboard brand new design, using the latest technology, CPU uses 32 bits ARM processor,improve the processing speed, the calculated data is more accurate and rapid electromechanical integration design, abandon cumbersome testing process of the artificial hand wheel is rotated, the real implementation of the test program, a determination of the accurate and efficient.(4)Using d/o lighting and observation geometry, diffuse ball diameter 150mm, diameter of the testing hole is 25mm.(5) A light absorber, eliminate the effect of specular reflection.(6)Add printer and imported thermal printer, without the use of ink and color, no noise when working, fast printing speed.(7) Reference sample can be physical, but also for data,? Can store up to ten only memory reference information.(8) Has the memory function, even if the long-term shutdown loss of power, memory zeroing, calibration, standard sample and a reference sample values of the useful information is not lost.(9) Equipped with a standard RS232 interface, can communicate with computer software.
-
Product
Micro Spectrophotometer
USPM-RU III
-
The USPM-RU III is a reflectometer that provides highly accurate spectral reflectivity measurements of small, curved, and thin samples without interference from rear surface-reflected light. The curved surface of the lens can be measured from a minute spot as small as ø60 µm formed on the sample surface. This provides the ability to use a goniometer to examine even the curved side lenses or other optical component.
-
Product
MPO/MTP Multi-Fiber Interferometer
-
Anfkom International Co.,Limited
It is an automatic and non contact fiber endface interferometer for both multi fiber and single fiber connectors. It can measure the geometry parameters of multi fiber connector such as fiber height,core dip, X and Y angel, radius of curvature with white light and measure geometry parameters of single fiber connector with red light. The software can display the surface of the connector in 3D image for a very short time, it need only 8s to test 12-core MT connector. It is intelligent , efficient,stable and accurate and very helpful in improving the quality of the product.
-
Product
Solid State Flasher, DC Input
A738
-
NAI’s A738 is a 2.5 A, DC Input, Aircraft Warning or Position Light Flasher. This solid-state, single-channel unit is designed for airborne use and performs to all applicable military specifications.
-
Product
Modular Infinity Microscope (MIM)
-
Applied Scientific Instrumentation
ASI Modular Microscope components consist of tube lenses along with adapters and accessories that either are primarily used in the collimated light space or adapters that are to be used on the image side. Collimated light adapters use the 38mm diameter C60-RING system to connect components. Focus-side adapters attached to lens tubes with either a 30mm diameter coupling to the I.D. of the C60-TUBE, or with a 50mm coupling on the O.D. of the lens tube.
-
Product
PXI-2521, 40-Channel, 2 A, DPST PXI Relay Module
778572-21
-
40-Channel, 2 A, DPST PXI Relay Module—The PXI‑2521 is a general-purpose switch module that features independent double‑pole single‑throw (DPST) armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2521 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
Product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
-
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
Product
IR Receivers
-
Vishay is the world's leading supplier of infrared (IR) receivers. Vishay IR Receivers offer a breadth of products, holders, application and technical support, and overall knowledge of infrared communication; infrared code learning, infrared light barriers, infrared proximity sensors including reflective sensors. Vishay's IR receivers are used for remote control and for transmissive and reflective sensors.
-
Product
Relay Buddy
190
-
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
Product
Gas Filter Correlation CO Analyzer
Model N300
-
Teledyne Advanced Pollution Instrumentation
The Model N300 is a microprocessor-controlled analyzer based on the Beer-Lambert law that is used to determine the concentration of carbon monoxide (CO) in a sample gas.The N300 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb Infrared (IR) light. The analyzer passes the IR light beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
Product
Desktop Spectrometer
-
Electro-Technic Products, Inc.
The RSpec Explorer is an educational tool which makes it possible for an entire class or lecture hall to study atomic emission spectra. This is a great device for hands-on student learning including having students identify the gas in an unknown spectrum tube. Your students will find the software (included) is easy to use right out of the box. Until now, it’s been nearly impossible to teach about light and color using traditional tools like diffraction gratings because you can’t determine if all your students are even seeing the same results of their experiments. But with the RSpec-Explorer’s camera and software system, you will be confident knowing that every student is seeing the same thing.
-
Product
Data Panel
ІТ-09Т
-
Display of measurement results of ambient dose equivalent rate(DER) of gamma radiation obtained from the BDBG-09 detecting unit of gamma radiation; Real time display; Air temperature display; Audio and light alarm when threshold levels of gamma radiation DER exceeded.
-
Product
DC Power Supply
PDS Series
-
This series of products is programmable DC switching power supply with high accuracy and single output. It is light and compact, adjustable in voltage and current, and has multiple operating modes. The whole system is completely controlled by the microporcessor (mou), and can easily use the communication interface (re-232) to connect with the computer (PC) to meet the user's requirements for automatic testing and automatic control. The software instructions are completely in accordance with the scpi command. The format makes it easy for users to develop automatic test and automatic control applications. Due to the full digitalization of the system, the data input is completely controlled by the keyboard and knob, which is fast, accurate, and convenient. Can be widely used in electronic product development, device testing, communications industry, laboratories and scientific research institutions.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Bias Ball Probe
POGO-1T30-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Energy Dispersive Spectroscopy (EDS) Platform
Octane Elect EDS System
-
The Octane Elect EDS System is an enhanced Energy Dispersive Spectroscopy (EDS) platform with the latest advancements in Silicon Drift Detector (SDD) technology and high speed electronics. Tailored for users who demand higher performance and functionality than the options available in entry-level systems, the Octane Elect EDS System provides excellent resolution and high throughput at an optimal value with a remarkable low energy sensitivity for light element detection and low voltage (kV) microanalysis.
-
Product
Programmable AC Withstand Voltage Insulation Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Small volume, light weight *Easy to operate, has keyboard lock function *Provide 5 groups memory setting, each group has four kinds of work mode LCD display Voltage gradient rise by time, real-time analysis and look for breakdown point
-
Product
NITlab Chassis Manager Card
-
NITLAB designed and implemented a Chassis Manager(CM) card to control and monitor NITOS nodes. CM card is comprised of a general-purpose microcontroller, an ethernet microcontroller and a relays circuit. General-purpose microcontroller supports a tiny web server and can serve http requests such as power on/off and reset. Furthermore, it returns the operation status of the node and can support a temperature & humidity sensor and a light sensor as well.
-
Product
Equipment
-
Based on a proprietary light engine, our solar simulation equipment delivers perfect and continuous artificial sunlight 24/7, allowing for accurate stability and performance assessments of solar cells at laboratory and industrial scales.
-
Product
Automated Thermal Stress System
ATSS Series
-
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
Product
Cable Sheath Testing and Fault Location System
Shirla
-
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
-
Product
LED Light Sources
-
LED light sources provide high power at a precise wavelength. A typical application for AvaLight-LED sources is fluorescence. They provide a long lifetime, short warm-up time, and high stability.
