-
Product
Push Cameras
-
Advanced Inspection Technologies Inc.
AIT's Pipe Inspection cameras and push cameras are designed for the toughest industrial inspection. Our different pipe inspection camera systems easily bends around tight radius pipes, heat exchanger tubes, oil lines, drain lines and more. See inside industrial pipelines as small as 13.0mm (1/2 in) diameter and up to 200 meters (600 Ft) in Length.
-
Product
Flex Power Right Angle Non Shut-Off Pulse Tools
-
The non shut-off right angle pulse tools are ideal selection when the operator needs to control the fastening process. It offers access for hard-to-reach fasteners in tight spaces. The drive on a right-angle tool is mounted at a 90-degree angle to the tool body. Designed for safe, reaction free operation for various industrial assembly applications. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
Product
Dead Weight Pressure Tester
-
Unitech Scales And Measurements Pvt. Ltd
Dead Weight Pressure Gauge Tester is ideal for testing and calibration of pressure gauges,pressure transducers,recorders,digital calibrators etc. The system used in the dead weight is vertically mounted precision lapped piston and cylinder assembly with accurately calibrated mass for loading the piston. Pressure is built easily by single cylinder pump at very high rate. The whole system is housed inside a stainless steel case with elegant look. Pressure ports are provided to fix the gauges to be tested. Acrylic see-through oil tank is designed to use it as oil reservoir.
-
Product
Seismic Analysis and Monitoring
-
Seismic analysis and monitoring have been designed on the base of the contemporary seismic studies. We can offer you a wide range of tools for geophysical surveys, seismic tomography, automated monitoring of bearing structures (structural health monitoring), seismic monitoring of oil piping systems.
-
Product
Oil Trace Moisture Tester
-
Weshine Electric Manufacturing Co., Ltd
WESHINE has developed Karl Fischer Titrator(KF Titrator) introduces the solid performance, simple operation and space saving design of the Compact KF Coulometers. Accurate results from 1 ppm to 5% water. Up to 4 shortcuts per user + 5 analysis methods.
-
Product
Ultrasonic Thickness Meters
-
Used for measuring thickness and corrosion of pressure vessels, chemical equipment, boilers, oil storage tanks, etc. in industries of petroleum, shipbuilding, power station, and machine manufacturing. Applicable to measure the thickness of many materials, e.g. Steel, Cast iron, Aluminum, Red copper, Brass, Zinc, Quartz glass, Polyethylene, PVC, Gray cast iron, Nodular cast iron
-
Product
Relays & Coax Switches
-
Teledyne Relays offers high-performance relays designed to survive the rugged conditions required for oil & gas exploration, industrial control, and military & space applications. Teledyne Coax provides RF & Microwave switching solutions for SATCOM, military & space applications, test & measurement equipment, and ATE systems.
-
Product
Harness Design and Manufacture
-
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
Product
Automotive Emission Analyzer
MEXA-584L
-
The MEXA-584L simultaneously measures CO, HC, CO2 (non-dispersive infrared: NDIR) and air-to-fuel ratio (AFR) or excess air ratio (A) in idle state. lt optionally measures O2, NO, engine speed (RPM) and oil temperature (TEMP). Lightweight and compact with a clear LCD and effortless operation, it can be used as a simple measurement instrument in any work situation.
-
Product
Fully Automatic Transformer Oil Test Set
OTS-A series
-
The Motwane Manufacturing Company
OTS-A series is fully automatic microprocessor based transformer oil test set designed with advanced features to measure breakdown voltage of insulation oil accurately. The OTS-A Series preprogrammed with worldwide acceptable standards.The user can define customized standards. The large LCD display with menbrane key pad for easy operation. It is provided with internal memory for 100 data storage & built-in thermal printer for onsite report. The kit is protected by automatic detection of poor input ground.The acrylic oil test vessel provided with adjustable electrode gap setting. The voltage calibrator for on site calibration saves cost & time of user.
-
Product
Multiple Gas Transformer DGA
MINITRANS
-
Based on the same core technology as the highly successful TRANSFIX the MINITRANS is a lower cost alternative, monitoring three key gases: Hydrogen, Acetylene and Carbon Monoxide (in ppm) plus moisture in oil (%RH & ppm). The measurement of these gases allows the user to detect a wide range of developing faults including arcing.
-
Product
Lasers
-
We design and manufacture advanced photonics tools for use in science, industry and education. Our lasers have enabled breakthroughs in quantum technology, biophotonics and chemical sensing and have been used by sectors as diverse as aerospace, defence, oil and gas, healthcare, food and drink. Known for their reliability and ease-of-use, our products such as SolsTiS, Sprite and Firefly are the tools of choice for researchers and innovators everywhere.
-
Product
Oil Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
oil analysis program is to verify that a lubricated machine is operating according to expectations. When an abnormal condition or parameter is identified through oil analysis, immediate actions can be taken to correct the root cause or to mitigate a developing failure.
-
Product
Turbine Flow Meters
CT15
-
Flows up to 15 lpm (4 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-esters
-
Product
Fully Automatic Solar Cell
Module Laminator-H
-
1. Model: BSL2236OAC-H2. Effective lamination area: 2200mm × 3600mm3. Dimensions: length 17410mm × width 3665mm × height 2164mm4. Heating method: heat conduction oil heating5. Compressed air source pressure: 0.6～0.8MPa6. Working vacuum degree: 100～40Pa7. Evacuation rate: 70L/S8. Temperature control accuracy: ±1.5°C9. Temperature control range: room temperature - 180°C10. Temperature uniformity: effective lamination area≤±2℃11. Lamination chamber height: 30mm12. Evacuation time: depending on the process, it is recommended to take 5 to 8 minutes13. Upper cover stroke: 300mm
-
Product
Viscosity Standards
-
Brookfield Viscosity Silicone and Oil Standards provide a convenient, reliable way to verify the calibration of your Brookfield laboratory viscometer/rheometer.
-
Product
Water Cut Meter
Model 5650
-
Teledyne Analytical Instruments
The Model 5650 Water Cut Monitor is designed to produce superior results in operating environments from the North Sea to the Sahara Desert. Delivering unmatched flexibility in material, size, features and configurations, the 5650 can be integrated into almost any oil carrying system. Applications include monitoring pipeline transfers, enhancing dehydration equipment efficiencies by monitoring water content before and after desalinization, early detection of undesirable conditions in petroleum storage facilities and detecting and rerouting oil with excess water content.
-
Product
Loss Tangent M in Dielectric Oil
TAND220A
-
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
Product
HV High Performance Circuit Breaker Analyzer
CBV-32
-
We conceived the CBV-32 to provide the best range of testing for electrical facilities such as circuit breakers (using gaz, oil, air, vacuum…) or synchronous condensers all the way up to 800kV and more. It combines Timing, Motion Dynamic Resistance Measurements, and Vibration, all in a single test.
-
Product
Thermowell
TSW400
-
Solid drilled thermowells to satisfy the needs of the Oil & Gas industry. The TSW400 has been designed around the ASME PTC 19.3 2010-TW standard for thermowell stress calculation. Fully compliant with the requirements of this most demanding industry and ASME standards.
-
Product
Flash Point Tester
-
Weshine Electric Manufacturing Co., Ltd
Closed flash point tester, when the test sample is used in a closed environment (such as transformer oil), to determine the closed flash point value of petroleum products. Use touch screen instead of keyboard operation, adopt foreign advanced technology, large LCD screen LCD full Chinese display man-machine dialogue interface, full screen touch key prompt input, convenient and fast, open, fuzzy control integrated software, modular structure, in line with national standards, the United States, EU and other standards.
-
Product
Dial Indicators
-
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.
-
Product
UNI-T Series
-
Weshine Electric Manufacturing Co., Ltd
mainly used to measure the wire resistance of cables, the contact resistance ofswitches, connectors, relays, the resistance of coils, motors, transformer windings, and equipment enclosures, lightning protection belts, ground beams, structures, cabinets, steel bars, Test the connection resistance between metal components of water pipes, windows, guardrails, radiators, assembly lines, etc. It is widely used in telecommunications, electric power, meteorology, computer rooms, oil fields, power distribution lines, tower transmission lines, gas stations, factory grounding grids, lightning rods, etc.
-
Product
Ultrasonic Flaw Detector
MFD800C
-
MFD800C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed main product. Unique design, sophisticated manufacturing, convenient operation, powerful function, It takes many advantages in one unit. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it can select the operating interface style and the LCD brightness according to environment. With humanizing interface design, the waveform show delicately. It can find the defects clearly in full screen. Single hand capable for holding operation, the curve making, probe calibration and other conventional operation can be completed automatically. Core processor CPU with 400M main frequency, it can complete the complex run quickly and realize intelligent defect analysis. Low power design with large capacity and high performance lithium ion battery module，it can work more than 8 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating way in one body, customer with different habits can operate it freely. It supports many languages. Its waterproof, oil proof, dustproof function can achieve IP65 protection level. It is the necessary professional precision instrument for defect detection, quality control, on-line safety monitoring and life evaluation in fields of oil, chemical, metallurgy, shipbuilding, aviation, railways and so on.
-
Product
FIre-Resistant Ceramic Penetrator Rated for 5kV and 200A
Flameguard P5-200
-
The FlameGuard™ P5-200 is a key enabling technology for a 5 kV - 200 A, three-phase dry mate electrical feedthrough system. Designed for offshore topside oil and gas platforms, where explosive and flammable conditions are likely, the feedthrough system is used to provide an electrical connection to downhole pumping systems. The feedthrough system is designed for dry tree operators and ESP pump manufacturers who want to reduce operating expenses over the life of the field, while improving system reliability and reducing safety risks.
-
Product
Flow Detector with Pressure Loss Compensation Function
FP-213S / FP-2140S
-
The Volumetric Flow Detector FP-213S, FP-2140S are volumetric flow detectors, used in combination with the Digital Flow Meter FM/DF series, for precision measurement of fuel flow such as gasoline, light oil and kerosene.They are suitable for those who want to evaluate the engine performance by measuring the minute flow rate of a small engine and making the fuel supply pressure as close as possible to the actual vehicle state.
-
Product
Automatic Insulating Oil Dielectric Strength Tester
OLT Series
-
Portable automatic testers of OLT series are designed for dielectric strength testing of insulating oils (mineral and synthetic) with AC voltage up to 100 kVRMS at industrial frequency (f = 50 / 60 Hz).
-
Product
OIP TYPE VOLTAGE TRANSFORMER
-
12kV - 145kV post type voltage transformers having Oil Impregnated Paper( OIP) as major insulation has been designed with several unique features.OIP insulated outdoor products are subjected to extreme climatic conditions and hence extra care is taken in the design and manufacturing of such transformers.
-
Product
Rotary Encoders
-
Our proven rotary encoder and resolver solutions are used worldwide in a variety of industries such as Medical, Oil & Gas, Aerospace, Packaging, Robotics, Paper and Steel, to name a few. Dynapar''''s vast product portfolio offers a wide selection of incremental and absolute encoders engineered with cutting edge optical or magnetic technology, brushed and frameless resolvers, and accessories. Dynapar offers a wide variety of optical or magnetic shaft encoders and resolvers, as well as any resolver or encoder product your particular application may require.
-
Product
Closed-Loop Servohydraulic Test Bench Control System
-
Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.
