References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
KYK-13 Interface
IP-Crypto
-
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
Product
Reference Frequency Generator
MFCh
-
*Frequency reproduction accuracy ± 2 x 10 -9 *Output frequency 1 Hz - 10 MHz *Output pulse signal 1 kHz The MFC is designed to generate high-frequency pulse signals with a frequency of 1 kHz and a frequency in the range from 1 Hz to 10 MHz along two output lines. The MFC is designed to operate in measuring systems based on the VXIbus trunk. In the MFC, a rubidium frequency standard is used as a reference frequency source. Time to reach the mode when the power source of the rubidium standard is turned on, no more than 10 min
-
Product
Dipoles
-
Tuned half-wave dipoles have been among the most important antennas from the beginning of rf-technique. The characteristics of half-wave dipoles have been calculable very early using the Maxwell and Hertz equations. Therefore the half wave dipole became a reference antenna.
-
Product
Pressure Calibrators
-
AMETEK Sensors, Test & Calibration
Our pressure calibrators offer a wide variety of features, accuracies, and pressure ranges. Included are intrinsically safe percent of reading calibrators, reference data recorders, wide-range dual sensor calibrators, and calibrators with built in pressure pumps. Many of our calibrators also offer current measurement, voltage measurement, 24 volt loop power supplies, and even complete systems with pressure pumps and calibration software. In many cases, one handheld calibrator can replace multiple instruments, reducing ongoing recalibration and maintenance costs.
-
Product
8 CANBus Channels, J1939 Protocol
CB2
-
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
Product
Meter Test & Calibration
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for meter test and calibration including portable power source, standard reference meter and meter test system. All products are accredited to the highest production standards with different options of measurement accuracy (class 0.05 and class 0.1).These enable them to cover different applications for test and calibration of different types of energy meters, electric transducers, indicating meters and so on.
-
Product
Rubidium Reference Oscillator
LPFRS-01
-
Rubidium reference generator LPFRS-01 is designed to generate a highly stable reference and clock frequency signal.
-
Product
Signal Analysis
Harmonic Distortion Analysis
-
The software is used for automatic measurement of the harmonic distortion factor and voltage r.m.s. of signals coming to the input channels of FFT spectrum analyzers. Adjustment to the frequency of the main component is performed automatically. The program is based on the measurement of the voltage r.m.s. of higher components by an external or internal reference signal.
-
Product
RF & Microwave Modules And Instruments
-
SHF Communication Technologies AG
In digital high speed test and measurement, a perfect clock signal is crucial for the generation of low jitter reference test signals. A SHF Synthesized Signal Generator (Synthesizer) used as a clock source can operate over several decades of frequency and is an essential part of any high speed test and measurement environment.
-
Product
8-Channel 200 MHz A/D with 64-Channel DDC, Virtex-6 FPGA - 6U VPX
Model 58662
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- 64 channels of multiband DDCs (digital downconverters)- Up to 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Industrial Calibrators
-
A temperature calibrator, often called a thermometer calibrator, is used to correct inaccuracies in installed thermometers and temperature sensors, because temperature measurement is a critical parameter in many industrial processes. Although simulators are sometimes called temperature calibrators or thermometer calibrators and may be used to provide thermometer calibration for the electronics in an installed system, a temperature source with a calibrated reference sensor is still required to provide a complete and meaningful calibration. Fluke Calibration industrial and field temperature calibrators include: Metrology Wells; Field Metrology Wells; field dry-well calibrators; handheld dry block calibrators; Micro-Baths; large target infrared calibrators; field IR calibrators; ice-point dry-well; and thermocouple furnaces.
-
Product
Machine Vision Camera - 2.3 MP, 41 FPS, Sony IMX249, Color
Blackfly USB3
-
The Blackfly® camera line combines Sony CCD, Aptina, e2v, and Sharp sensors with a host of unique features. For FLIR area scan cameras with the latest sensors and most advanced feature sets, please refer to our Blackfly S and Oryx camera families.
-
Product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - PCIe
Model 7053
-
- Supports Xilinx® Zynq® UltraScale+" RFSoC FPGA- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2, and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional front panel dual optical MPO interface for gigabit serial communication- Unique QuartzXM eXpress Module enables migration to other form factors- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
DDR4 Parametric Test Reference Solution
-
Keysight's DDR4 parametric test reference solution helps verify the signal integrity of DDR4 memory designs according to JEDEC specifications.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
3U OpenVPX High Density Multifunction I/O Board
68CB6
Multifunction I/O
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
Product
Bloomy Simulation Reference System
System
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
SENSORBOX MODULE
MDGDSSBM
-
*Turn your MDMAX, MDMAX2A or MDMAX3 into a unique sensor simulator to substitute known good waveforms for intermittent components that cannot be verified*Sensor simulation tests include: DC voltage, fixed frequency, pre-defined waveform and hand-drawn waveform*Contains a library of standard reference waveforms that can be modified by the stroke of a finger
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUCs (digital upconverters)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- 2 GB of DDR3 SDRAM; 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
One-Shot Image Checker
Focus-6500IA (TASCAL)
-
This is the image checker which inspects boards by comparing pre-registered reference image with captured image of inspected board.(Pattern Matching processing)
-
Product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - XMC
Model 71851
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex Ultrascale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the Kintex - Ultrascale FPGA for custom I/O- Optional 400 MHz 14-bit A/Ds- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Tester Electrical Interfaces
-
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
Product
Embedded Local Oscillator Capability
S93084B
-
The S93084B tunes the network analyzer’s receivers to the output frequency of the converter under test without having to access internal LOs or a common reference signals. For converters with embedded LOs, this enables measurements of match-corrected conversion loss/gain and absolute group delay (requires S93082B and S93083B), gain compression versus frequency (requires S93086B), intermodulation distortion (requires S93087B), and noise figure (requires S93029B).
-
Product
Gyroscopes
-
A device consisting of a wheel or disk mounted so that it can spin rapidly about an axis that is itself free to alter in direction. The orientation of the axis is not affected by tilting of the mounting; so gyroscopes can be used to provide stability or maintain a reference direction in navigation systems, automatic pilots, and stabilizers.
-
Product
Compact Timing Systems
NanoSync IV & NanoSync IV Low Profile
-
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare applications.The NanoSync IV-SA-Rb has been demonstrated to be compliant to the Joint Airborne SIGINT Architecture (JASA) Version 3.0, Annex 1, for Time, Frequency, Navigation and Geodesy (TFNG), making it suitable for Electronic Warfare (EW) COMINT and ELINT applications in fixed site, airborne and shipboard environments.
-
Product
VME Analog Output Module
DP-VME-2115
-
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
-
Product
Calibration Software
-
AMETEK Sensors, Test & Calibration
Our calibration software provides an easy way to calibrate gauges, RTD´s, thermocouples, transmitters, thermoswithes, and pressure switches. Complete a full calibration from entering the details of the gauge to printing out a calibration certificate. Reduce operating time by automating calibration procedures, reduce sources of error by automatically reading and storing values from the reference, and customize certificate templates to fit your needs.
-
Product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
-
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Cable Assembly, Receiver, TriPaddle, 72", 200 Pin Male LFH, M3 jackscrews
540105040505
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 72", refer to drawing for wire list, M3 jackscrews
-
Product
RFID Software
-
Radio Frequency Identification technology, commonly referred to as RFID, uses electromagnetic fields for the purposes of identifying and tracking objects. More recently, the technology has moved into mainstream applications that speed up the handling of manufactured goods and materials by attaching RFID tags to them. RFID technology has been around since the 1970s but its high cost and limited practical applications have discouraged its use up until recently.
