Programmable Attenuators
-
product
Step Attenuators
A stepped attenuator from Pasternack. Our BNC attenuator is a RF step attenuator design. This 50 Ohm manual step attenuator is precision manufactured to RF and microwave industry specifications.
-
product
Programmable AC Power Source
6400
Chroma Systems Solutions, Inc.
The Chroma 6400 series Programmable AC Power Source uses state of the art PWM technology to deliver pure, instrument grade AC power at a very low cost never achieved before. The 6400 AC power source offers maximum rated power for any output voltage from 0 to 300VAC, at any frequency from 45 to 1K Hz. It is not only suitable for commercial applications (47-63Hz), but also for avionics, marine, military applications at 400Hz.
-
product
Coaxial Fixed Attenuator, DC to 18 GHz
8491B
The Keysight 8491B coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. It has type-N connectors with a maximum frequency of 18 GHz. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
PXI Resistor Module 2-Channel 1.5R to 4.09k
40-293-023
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Digital Step Attenuators
Ranatec’s digital step attenuators covers all mobile frequency bands and gives a calibrated attenuation range of more than 90 dB in steps of 0.25 dB. All Ranatec digital attenuators are built as modules and offers both serial and parallel control logic.
-
product
Programmable DC Electronic Load
63000 Series
The 63000 Series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power suppl ies, A/D power suppl ies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices. The 63000 Series offers models in two operating voltages 150V models, with 250W and 350W power levels up to 60A in a single unit. Their compact and light weight design make these loads easy to move around which is ideal for R&D and design validation. Each model of the 63000 Series has unique user-def ined waveform (UDW) funct ion capable of simulating real-world custom waveforms. In addition, a data storage function has been built in for saving and recalling up to 100 stored settings at any time. For automated testing, these save and recall functions can save a great deal of time. The 63000 Series has 3 power ranges that can precisely measure the voltage and current in real time. Since short circuit testing is a critical test item, the 63000 provides short circuit simulation to effectively address application demands for power and automated testing.
-
product
Controllable, Programmable Clocked AC Source
EAC-AFV
*Output from 15kVA to 2000kVA*Output voltages 0VAC to 700VAC / 1000VDC per phase*Maximum currents up to 2000A per phase*Simulation of 1- and 3-phase networks (worldwide)*Variable frequency of up to 2000Hz, sine, square, triangle*Indication via graphic display
-
product
Programmable RF Multi-Port Test
A programmable multi-port switch between your RF device under test and a Vector Network Analyzer significantly speeds up testing.
-
product
Fixed Attenuators
A fixed 1 dB attenuator from Pasternack. This 1dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
product
Programmable AC Laboratory Power Supplies, Motor-controlled
Programmable AC Laboratory Power Supplies, Motor-controlled
-
product
Programmable DC Electronic Loads (conventional and regenerative)
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2.5Ω to 201kΩ
40-252-041
The 40-252-041 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 201kΩ with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Fully Programmable Digital Design with Wireless Remote Control
VLF E Series
The VLF E Series uses a state-of-the-art, switching power supply design with wireless computer controls. Equipped with HVI’s E-Link software, the E Series stands among the most advanced cable testing systems available. Our customers praise its flexible data capture and reporting capabilities, full remote operation via XBee wireless technology, and seamless tan delta testing with HVI’s TD units.
-
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-020
The 40-297A-020 (PXI) and the 42-297A-020 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 472 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Programmable Relays
Omega offers a wide selection of programmable relays. From universal remote I/O modules to pressure switch accessories, you'll find everything you need to complete your application here.
-
product
Programmable Ground Resistance Tester
AllWin Instrument Science and Technology Co., Ltd.
Executive test in 40A/60A of UL60950-1Test resistance range 0~510m ohmOutput current range 5~40A
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 6.97kΩ
50-298-030
The 50-298-030 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Amplifier And Attenuator Modules
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
product
Variable Attenuators
Continuously variable attenuators from Pasternack are available in 50 Ohm impedance and with SMA connectors. SMA continuously variable attenuators have RF db attenuation values that range from 7 dB to 40 dB. The frequency range of our continuously variable attenuators is from 1 GHz to 18 GHz. This variable attenuator product line includes low to high power attenuators which have the power handling up to 5 Watts.Variable attenuators from Pasternack include female genders and can be bidirectional, depending on the power rating. Our continuously variable attenuators are manufactured to precise industry specifications and the bodies are constructed of. Pasternack commonly uses Pi attenuators or Pi pads for its continuously variable attenuator designs.
-
product
Programmable Voltage Reference Plug-In
ProDAQ 3202
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
product
Low cost Device Programmer for PC/Parallel
ChipMax
ChipMax is a cost-effective, high quality industrial-grade device programmer with parallel-port interface that is suitable for most programming needs without using any extraneous personal family modules.
-
product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 2.97MΩ
50-298-151
The 50-298-151 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 2.97MΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-036
The 40-254-036 (PXI) and 42-254-036 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 395kΩ with 8Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Programmable Power Supplies
GENESYS+™ Rack DC Power Systems
The GENESYS+™ High Power Programmable Rack DC Power System platform provides advanced features in a light-weight portable high power density profile with a comprehensive set of built-in user-friendly interfaces that include a multi-functional front panel, LAN (LXI 1.5), USB (2.0), RS-232/RS-485 and Isolated Analog (5V/10V) along with several optional digital communication interfaces (IEEE, EtherCAT or Modbus-TCP).
-
product
Attenuator Interconnect Kit, 2.92 mm
11716D
The 11716D attenuator interconnection kit provides the necessary parts to connect 84904L and 84906L programmable step attenuators in series.
-
product
Programmable DC Power Supply
CBCT
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
-
product
Programmable AC/DC Hipot & Insulation Resistance Tester
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC Hipot & Insulation Resistance Tester can do hipot test and insulation resistance test.
