Programmable Attenuators
-
Product
Multi-module Programmers
-
Xeltek offers both traditional gang programmers and modern stand-alone models for production cluster setups. Traditional gang programmers come with four independent sockets that allow chips to be programmed concurrently.Recent trends have shifted from gang programming to cluster setups. Cluster setups consist of multiple stand-alone programmers operated by one operator for enhanced efficiency and cost-savings during production.
-
Product
PXI Programmable Resistor Module 6x24 Bit, 0 Ohm to 16M Ohm
40-295-121-6/24
-
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Variable Optical Attenuators
5418
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Non-Isolated
SC7
-
Module SC7 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications. SC7 is the same as SC1 except SC7 reallocates the pins used for CTS Flow Control as four (4) additional system grounds.
-
Product
Programmable Boards
LEO Board
-
LEO Board is a free programmable Aid for students who want to practice and enlarge their knowledge in programming of microcontrollers.
-
Product
PCI Precision Programmable Resistor Cards
-
Pickering's PCI precision programmable resistor cards feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-121
-
The 40-297A-121 (PXI) and the 42-297A-121 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 925 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 5.82MΩ
50-297-052
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Programmable Ammeter
IM1953
-
Programmable Digital Ammeters are DC current indicators with High and Low alarm limits. Also known as AC Ammeter, Electronic Ammeter, etc.
-
Product
Programmer
TurboProg
-
TURBO-PROG supports two types of turbo actuators:*Hella actuators with the following markings:712120, 730314, 781751, 763797*Siemens actuators in a metal-plastic housing used in turbochargers made for VW/Audi with 2.7TDI and 3.0TDI engines.
-
Product
In-System Programmer for ARM
MPQ-ARM
-
Supports Nuvoton M05x and NUC1xx device families Field Upgradeable - always supporting the latest devices Secure image management - protects your IP In-circuit gang programming of up to four devices at once Can be deployed in arrays to program up to 64 devices in parallel Stand-alone, PC-controlled or ATE-controlled operation Automatic device serialization
-
Product
LED Test Programmable DC Electronic Load
IT8912E Series
-
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 26.7kΩ
50-297-032
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Universal Programmable Transmitters
-
Omega offers a large selection of programmable universal transmitters that accept universal inputs including mA and Vdc process signals and all commonly used temperature signal types.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-044-HI
-
The 40-230-044-HI (PXI) and 42-230-044-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Manual Step Attenuator
WATT-3SM352
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Programmable 70W Electronic Load
MightyWatt R3
-
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
-
Product
Programmable DC Electronic Loads (conventional and regenerative)
-
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.
-
Product
Programmable Linear DC Power Supply
MPS-S Series
-
Triple channel programmable DC power supply is with high resolution, high precision and high stability, over-voltage and over-heat protection are available. Series and parallel operation are also provided. The resolution is 10 mV/1 mA.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 52.4kΩ
50-298-133
-
The 50-298-133 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Programmable Electronic Loads
SFL Series
-
The SFL DC Electronic Load Series is a multi-functional programmable DC Electronic Load series that offers power levels of 300W (3U Half-Rack) and 1kW (3U Full-Rack) with high-speed current control (no dynamic overshoot/oscillation), high slew-rate (up to 30A/us) and stable operation at low voltage with no turn-On delay. It is lightweight and has a user-friendly front panel with built-in (USB) and optional (IEEE) communication Interfaces.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Direct Reading Attenuator
DAXE
-
DAXE Millimeter-Wave Direct Reading Attenuator is a measurement instrument for signal level setting or loss measurements in waveguide networks. It also can be used for calibration of other attenuation measurement instruments. Direct Reading Attenuators have rotary-vane design. The value of attenuation is determined by rotation angle of resistive film with respect to the waveguide channel. Attenuation value does not depend on of frequency.The Attenuators are provided in waveguide bands between 18 GHz and 225 GHz.
-
Product
Variable Optical Attenuator Module for Multimode Fiber Applications
81578A
-
The Keysight 81578A variable optical attenuator is designed for multimode fiber applications and features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
0-5kv Programmable AC Hipot Insulation Tester
7112
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC withstand voltage insulation tester Feature: Small volume, light weight Easy to operate, has keyboard lock function
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Waveguide Tunable Attenuators
-
*Low Insetion Loss*Full Waveguide Band Coverage*Precise Adjustment*High Maximum Attenuation
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
