Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
Cable Assy 9-Pin D-Type, M/F, 1M
40-970-009-1m-MF
Cable Assembly
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 0.5m, 250 Port
A500RMR-C-5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Display Driver Test System
T6391
Test System
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
Product
SparkFun Pressure Sensor Breakout
MS5803-14BA
-
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid. Depending on how you interpret the data, you can determine altitude, water depth, or any other tasks that require an accurate pressure reading. What makes the MS5803-14BA unique is the the gel membrane and antimagnetic stainless steel cap that protects against 30 bar water pressure.
-
Product
Boards
MIL-STD-1553
-
The MIL-STD-1553 multi function interface cards are compatible with all common variations of MIL-STD-1553 and provides a wide range of features normally found only on full size testers. The card can operate simultaneously as a Bus Controller (BC) and/or multiple (up to 32) Remote Terminals (RT), or as a Triggerable Bus Monitor. The card supports error injection and detection.
-
Product
COM Express Embedded System – CM07
AS-CM07-CME-A
-
The CM07 COM Express Embedded System has been custom designed for a specific medical application in the field of radiation therapy. This unit integrates many features and interfaces which dramatically reduced the size compared with previous PC server based solution, as well as significantly increasing reliability.
-
Product
Broadband Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-32Gbps / DC-17GHz) tunable clock/data phase shifterDelay adjustment range of 265psExhibits low jitter and limited temperature variation over industrial temperature range1GHz of bandwidth for the phase adjustment tuning portFully differential CML input interfaceFully differential CML output interface with 600mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 1WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
3U VPX Processor Card
VPX3-1707
-
Curtiss-Wright Defense Solutions
Maximize performance in SWaP-constrained environments with the VPX3-1707, a powerful 3U OpenVPX single board computer designed to bring Arm’s unparalleled performance per watt to rugged, embedded systems. With advanced security capabilities and flexible I/O interfaces, the VPX3-1707 is a next-generation innovation for today’s C5ISR applications.
-
Product
Timing Controller
MS 2009
-
MS5128 Timing Controller has programmable logic generation, Input Output Signals Interface, Timings, macro-cells, Pins, internal timing delay and Signal Levels for airborne microprocessor boards.
-
Product
Video Signal Generator
PC Slot Type
-
M-100AD/A/C/Y/H/D, PCI type Signal Generator, was designed to make user can insert needed slot at Computer. Slot composed with Analog & DVI, Analog, CVBS, &S-Video, DTV, HDMI nd DVI type. It is operating with exclusive PC Program(User Interface) which is Master supplied.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
Potentiostats
-
Whether you're looking at a single-channel potentiostat or multichannel potentiostats, Gamry has a system for you. Gamry's two families of potentiostats are the high-performance Reference line and the more value-oriented Interface line.
-
Product
CoolMaster
1000D
-
CoolMaster 1000D is versatile bridge device connecting Daikin VRV Air Conditioning systems and any RS232 or USB capable device like Home PC, Embedded PC or Home Automation Controller. Exposing simple interface over RS232 communication line or USB bus, CoolMaster gains user application full control on indoor units and provides access to VRV system parameters. In other words CoolMaster hides complexity of internal Daikin Communication line (including very unique physical layer) and instead gives simple, comprehensive, well documented protocol running on popular RS232 or USB connection.
-
Product
Central Office Line Simulator
AI-7280
-
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Product
Connector Blocks for Interfacing to Ribbon Cables
-
VI Control Systems has designed several connector blocks for mating ribbon cables to screw terminals. Our design goal was to make the connector blocks small and inexpensive. Connector blocks are mounted by using 6-32 stand-offs. The connector blocks feature a ground plane that is connected to the mounting screw holes.
-
Product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
100MHz DDS Signal Generator
408A
-
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
Product
VPC Receiver Frame
ABex REC21-84TE-EXT
-
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
Product
Coaxial Programmable Attenuators
-
Coaxial attenuators are constructed with passivated stainless steel for durable use in both engineering labs and production line environments. These coaxial attenuators are designed and manufactured for low VSWR, low insertion loss and high attenuation value accuracy. The standard offering covers the frequency range of DC to 110 GHz and includes various interface options from 2.4 mm to 1 mm connector types as well as both male and female interfaces. The power handling of standard models is 0.5 to 1 watt continuous wave (CW). Higher power handling levels and different attenuation values and connector types from those listed below can also be requested.
-
Product
Protocol Control Control
PC2
-
The PC2 software from SCSI Toolbox, LLC brings a new level of parallel SCSI protocol control to your test environment. Designed in cooperation with LSI Logic to work with their Fusion-MPT Message Passing Interface technology, PC2 allows all negotiated parameters to be displayed or set for all devices connected to any SCSI Host Bus Adapter based on the LSI53C1030 chip set. PC2 also provides the means to generate hardware SCSI bus resets.
-
Product
Thermometer
S0122
-
Thermometer is designed for record of temperature. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
Product
Optical Communication Probes
-
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
Product
Imaging Modules
-
Teledyne e2v has developed compact MIPI modules which feature our own high performance CMOS image sensors inside a pre-focused, industrial-grade scanning optic. As a turnkey sensor/optics for imaging systems, these modules offers customers significant reduction in development time and cost savings. Only a few screws are needed to mount the module, with simple connection to the image processing system through an FPC cable connector. Software development efforts can also be reduced by using some limited API-layer Linux software drivers. This enables the module to be seamlessly interfaced to popular ISP platforms.
-
Product
EMX-7XXX
Programmable Resistor Module
The AMETEK VTI Instruments EMX-7000 Series PXIe Precision Programmable Resistor Ladder modules provide four independent channels of programmable resistors. The EMX-7004 is capable of delivering exceptional stability and accuracy for any resistance value between 1 Ω to 16,383 Ω and can be adjusted in 1 Ω increments through the software application programming interface (API) or dynamic soft front panel.The EMX-7005, EMX-7006 and EMX-7007 are perfect for applications requiring higher resistance values, with programmable settings ranging from 163 kΩ to 16.383 Mohms, while the EMX-7014, 7015 and 7016 are ideal for general purpose applications not requiring ultra high accuracies.
-
Product
Remote Data Acquisition
-
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
Product
Multichannel Memory-Mapped ARINC 708/453 Interface Card
EXC-708mPCIe
Interface Card
The EXC-708mPCIe is a multichannel, memory-mapped ARINC 708/453 interface card that supports two ARINC 708/453 channels, each programmable as transmit or receive. Each channel implements a 64K x 16 FIFO and supports polling and/or interrupt driven operation. The card complies with the PCI ExpressTM Mini Card standard. It’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 708 interfaces and for performing system simulation of the ARINC 708/453 Weather Radar Display databuses, both in the lab and in the field. In Transmit mode, each ARINC 708 word is written to the FIFO as a block of 100 16-bit words. In Receive mode, each ARINC 708 word is stored in the FIFO as a block of 103 16-bit words. The first two words comprise the 32-bit Time Tag, indicating the word’s time stamp. The next 100 words comprise the 1600 bits of the ARINC 708 word, which are followed by the Status Word.The EXC-708mPCIe card comes complete with C drivers including source code.
-
Product
Interface
RAR-XMC
Interface
Designed for embedded, laboratory and simulator applications, the RAR-XMC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, receive message time-tagging and error detection, and IRIG-B receiver (AM or DC/TTL) and generator (DC/TTL).
-
Product
PCI Express Optical Link Board
SIS1100-E2
-
The SIS1100-e2 is the follow up card to our SIS1100-eCMC board (without CMC carrier functionality). It was developed to extend the lify cycle of our PCIe to VME interface. For software/driver compatibility reasons we still employ the PEX8311 PCI Express to local bus bridge chip.
-
Product
Octal 4 Gsps 12-bit ADC
ADF-O4012
-
The DEG ADF-O4012 FMC includes eight 12-bit, 4 Gsps RF analog-to-digital converters (ADC). The ADF-O4012 features a 16-lane, 24.75 Gbps JESD204C interface, flexible clocking and triggering options. This ADF-O4012 leverages two Analog Devices AD9209 MxFE (Mixed Signal Front End) ICs, elevating the technology to a new level of integration.
