Voltage Testers
See Also: Proving Units, Power Testers, Voltage Detectors
-
Product
AC/DC Withstand Voltage Test
WB2671A/WB2671B
-
• Output voltage: 0-5kV (AC/DC); • Cutoff current range: AC 0~20mA (WB2671A)/0~100mA (WB2671B); DC 0-20mA; • Test time: 1-60s; • Transformer capacity: 750VA.
-
-
Product
Hipot Tester
Sentinel
-
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
Product
Leak Testers
-
Vidac has installed various versions of Leakdown testers for products such as:ValvesSealsConduit fittingsExplosion-proof cases
-
Product
LOADpro Load Testers
-
LoadPro is an external Web load testing service. A LoadPro test simulates actual user traffic from outside your network, stressing your entire infrastructure in order to discover bottlenecks that impact performance under peak traffic.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
Jerking Tester
JLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard:JB/T4279.5-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.000mm and below;Built-in small ultra-quiet air compressor would provide power supply and automatic constant pressure;Samples, while being jerked, would not move and slip out;
-
Product
AMIDA IGBT Tester
600
-
KVI Source: 1 Channel 4Q V/I Source; ±1000V, ±10mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% accurate reading of Range
-
Product
Battery Testers
EEST 50-60
-
Charge/discharge and test benches for aerospace batteriesCharge/discharge benches for the maintenance, the certification, the training and the homologation of all industrial battery types
-
Product
Portable Appliance Tester
PAT-2
-
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Confi guration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (PAT) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplifi ed set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
Product
Pitot-Static Tester
PS-525
-
The PS-525 Pitot-Static tester is a low-maintenance digital tester that is fully portable.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
Low Circuit Tester
26250
-
Helps locate shorts or breaks in wiring. Complete with insulated grounding clip.
-
Product
Mobile & Wireless Testers
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Mobile & Wireless Testers are the most cost-effective test solution for those in wireless manufacturing test, service test and handset repair requiring a multi-technology platform. By quickly testing GSM, GPRS, EDGE, WCDMA (UMTS), 1xEV-DO and TD-SCDMA terminals, we provides the lowest total test cost per device and drastically reduces production downtime because one system can easily switch from one technology to another.
-
Product
Flexible Functional Tester
igentic® 421t
-
Electronics customers require greater test flexibility to address the growing trend towards high-mix, low-volume printed circuit board (PCB) production. Sterner Automation is pleased to introduce the igentic® 421t, the next generation of automated test solution specially engineered to address these challenges. The igentic® 421t provides the flexibility, reliability and efficiency needed in one standard platform, allowing our customers to test multiple PCB's and significantly reduce individual product testing costs.
-
Product
Mechanical Testers
-
Actron’s wide variety of mechanical testers includes specialty tools, compression testers, vacuum pressure gauges and advanced timing lights. All mechanical testers work effectively on most foreign and domestic vehicles, small engines, motorcycles and other recreational vehicles to save you time on inspections and repairs.
-
Product
HIPOT Insulation Testers
-
Crown high voltage, transformer type hipot insulation testers are safe, easy to use for quick, positive determination of grounds, shorts, and broken wires in motors, transformers and other low voltage equipment or wiring systems. A turn of the selector switch gives a selection of seven voltages;500, 1080, 1250, 1500, 1750, 2000 or 2500 volts calibrated to +/- 5% accuracy; NEMA recommendation for insulation test is twice normal voltage plus 1000 volts. Since this instrument has a capacity of 2500 volts, it readily accommodates all normal requirements.
-
Product
High Voltage Cable/Harness Test System
CKT1175-50
-
The CKT1175-50 is a high-voltage wiring analysis system that features a switching matrix that can be distributed around the workshop or in and around the assembly to be tested. This system is expandable in 100 or 150 test point increments to 96,000 test points, and is available with a variety of adapter cable interface connectors, with the standard being the CKT MAC interface system
-
Product
UMTS / GSM Tester
-
manufacture a range of items that can be used in UMTS and or GSM propagation testing. These products have been designed against customers requirements.
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
LED tester
-
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
-
Product
High Voltage Probe Meters
-
Shanghai Beha Electronics Co., Ltd.
*High voltage test probe *is a high voltage probe that is used with Oscilloscope● Attenuation Ratio: 1000:1*Measuring range: AC 20KV/DC 30KV
-
Product
Professional Cable Tester
1EA560
-
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
-
Product
Dissolution Tester Accessories
-
Teledyne Hanson's diverse range of dissolution tester accessories significantly expands the functionality of their instruments, catering to various applications such as small volume testing, Chinese small volume testing, semisolids testing, and immersion cell usage per USP <1724>. The lineup includes:- Precision dissolution vessels- Vessel covers- Paddles (USP Apparatus 2)- Baskets (USP Apparatus 1)- Paddle over disk “transdermal sandwich (USP Apparatus 5)- Rotating cylinder (USP Apparatus 6) - Sampling probes- Small volume kits- Filter block kits- Humidity-sealed dosage-drop chambers- Stationary basket and cover
-
Product
Combined Handset Tester
COMPRION SIMfony
-
COMPRION SIMfony is a GCF/PTCRB validated system for comprehensive 3GPP handset testing. With the integrated air interface functionality, the system includes USAT, USIM and SAT tests. Operating with the system simulator Anritsu MD8470A, all procedures and tests are integrated, automated and controlled using the IT? GUI. Both COMPRION SIM simulators IT? Platform for conformance and IT? Prove! for pre-conformance testing are usable within the system.
-
Product
Precision Voltage and Current Sources
VI-700
-
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
Product
CDM Tester
-
Hanwa Electronic Ind. Co.,Ltd.
The tester implements to test the withstand voltage which occurs when the device contact to different electric potential object.
-
Product
Automatic Dielectric Tester
LD-LADT-A10
-
Automatic Dielectric TesterLD-LADT-A10is a fully automatic oil tester. The oil tester adopts industrial SCM to control which is applied to integrate circuit. It features anti-jamming technology which largely improves the machine capacity.
-
Product
Optical Tester
Model C
-
The Model C Optical Tester is just such a device. Extremely small geometric distortion and focal length deviation can be viewed and measured easily.
