Voltage Testers
See Also: Proving Units, Power Testers, Voltage Detectors
-
Product
High Voltage Probe
HVP-15HF
-
*MAX.VOLTAGE:15KV DC.*BANDWIDTH:DC~50MHz.*DIVISION RATIO:X1000.*SIGNAL/NOISE:>60dB(1KHz)
-
Product
Voltage Controlled Amplifiers
-
Teledyne Microwave Solutions (TMS) offers a variety of high-performance voltage controlled amplifiers operating over a 5 to 2500 MHz range. These VCAmps feature an AGC range of 20.0 - 50.0 dB and Response Times from 3 – 25µs. TMS has a broad range of component products to meet your demanding needs.
-
Product
AC Voltage Sensors
-
Continuously monitor single or three-phase power lines for over or under voltage conditions with DARE?s AC voltage sensors, voltage monitors, and voltage sensing relays. DARE?s complete line of AC Voltage Sensors will protect system equipment and circuitry from voltage that is hazardous or unsuitable for operation.
-
Product
Voltage Pulse Generator
SKS-IV10J
-
Shanghai Sanki Electronic Industries Co., Ltd.
The voltage pulse generator SKS-IV10J is completely designed in accordance with the requirements of the impulse voltage chapter in OIML R 46-1/-2; it meets the requirements of the new IEC60255-5 and GB14711 standards; the leakage current detection alarm function is added, and the leakage current limit can be Adjustment; using linearized high-voltage power supply, low noise, high stability, high voltage accuracy and long service life.
-
Product
High Voltage Probe
HVP-39pro
-
* 39KVDC+ACpeak* 900MΩ Impedance* DC~50MHz(-3dB)* 1000:1 for Oscilloscope* Very Low Nosie
-
Product
Dual-Range High Voltage Non-Contact Tester
HVNCVT-1
-
Use to check for the presence of voltage in overhead conductors or find faults in cables.LOW range for 50V AC to 1.5kV AC.HIGH range for 1.5kV AC to 132kV AC.Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case.
-
-
Product
Voltage Detector
-
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
Product
Differential Voltage Probes
DP150/DP200pro
-
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
-
Product
Battery Voltage Supervisor
BVS
-
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
Product
Voltage Variable Attenuators
-
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
Product
Dual High Voltage Power Supply Tester
MS 1110
-
DHVPS Tester is used to test and service the dual high voltage power supply units. High Voltages of range from 4KV to 11KV can be tested.
-
Product
Voltage logger0 to 25V
TK-4702
-
Supplied with an input cable, this logger can measure voltages up to 25V DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.
-
Product
Low Voltage Holiday Detector
M1-AC
-
For use such as: Coatings, in-plant environments, rebar, pipelines, sheet materials coated with thin film under 20milsa,
-
Product
LXI High Voltage Matrix
65-218-121-CC
-
The 65-218-121-CC is a plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 1000V without access to the chassis backplane.
-
Product
Thermal Voltage Converter
1395D
-
The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.
-
Product
High and Low Voltage Detector
279A HD
-
Standard Electric Works Co., Ltd
Compact and light weight. Self-test function. Voltage detection：80V~11.4kV AC. Waterproof: IP65. Identify Line (Phase) and Neutral. Operation starting voltage. Low voltage: 65±15V. High voltage: 2000±200V.
-
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
Product
Rub Tester and Abrasion Tester
RT4
-
This comparative test works by abrading a printed sample against a reference material under known conditions. The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.
-
Product
Surge Voltage Generator
SSG 3000
-
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
Product
High Voltage Test System
CKT-1180
-
The CKT 1180 is a High-Voltage Test System with up to 3500 VDC and 2800 VAC RMS leakage test capabilities.Originally designed for High-Speed Rail, the CKT 1180’s focus is to test assemblies that require extremely high reliability and work at elevated voltages.
-
Product
Non - Contact Voltage Detector
Model 273 HP
-
Kusam Electrical Industries Limited
The 273 HP is a Non-contact voltage detector. It has two ranges for selection.The 273 HP consists of an internal pickup sensor, a function selection switch, a visual and a sound annunciator. With the 273 HP, physical contact with electrical conductors is not necessary when testing for live lines. Its sensor senses the radiated field which surrounds live conductors. Radiated field strength increases with voltage and decreases quickly with distance or earth shielding
-
Product
Surge Voltage Generator
SSG 500
-
Cable fault location with the BAUR SSG 500. The SSG 500 surge voltage generator is arranged in a 19'' housing. Maximum safety is achieved with the electrical safety control unit, the automatic discharge unit, the fully enclosed design and separate protection and system earth.* 6 output voltages up to max. 16 kV available* Electromagnetically actuated surge switch* Preselectable surge energy: 288 / 512 Ws (in all voltage ranges)* Automatic discharge unit
-
Product
High Voltage Probe
CP-3308R
-
*100:1 scope probe *300MHz Bandwidth *Read out Function *Division Ratio x 100 *100MΩ Fix Input Impedance *1500V DC Working Voltage (CAT Ⅱ) *2000V AC peak to peak MAX. (CAT Ⅰ) *CE Approved.
-
Product
Voltage Controlled Oscillators
-
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
Product
sbRIO-9223, Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785480-01
-
Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO-9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO-92233 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO-9223: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
-
Product
DC Tester
-
The DC Tester is a Voltage and Ampere breakout for measuring DC current from 0-26V at 3.2A Max (when used with the USB Tester OLED Backpack). The DC jacks make it easy to measure a wide variety of devices by placing it inline between your power supply and your project without splicing cables, just like the
-
