Noise Figure
delta of UUT noise to ideal.
-
Product
Noise Testing Software
GN-1100 Series
-
This software has a comparator function for abnormality diagnosis based on sound/vibration analysis.You can perform simultaneously the tracking analysis and pass/fail judgment for 2 revolution input channels.It is ideal for vibration analysis of CVT and in-line 100% inspection such as carrier noise analysis of motors.
-
Product
Pulse Function Arbitrary Noise Generator
81160A
Arbitrary Waveform Generator
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
Product
Noise Board
332D-11 VG
-
This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 3m
N1425B
Coaxial Cable
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
Product
Noise Sources
NC3208
-
It offers a high ENR output AWGN noise over a wide frequency range. This Noisecom noise source has excellent stability with temperature and voltage for tough environments. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including radar warning receivers (RWR), built-in test equipment (BITE), military aircraft, and Wi-Fi.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
Noise And Vibration Tester
-
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
Product
Ultra Low Noise DC Power Supplies
R4G Series
-
R4G series are series regulator system DC power supplies so that enabled setting and reading out more fine output with a 4-digit indicator on furont panel and a high resolution D/A and A/D converter adopted newly.
-
Product
Noise Monitoring System
Harmony
-
A system that consists of automatic noise measuring device, transmission device, computer system, and operation analysis software, and provides accurate data necessary for establishing noise-related policiesby providing real-time information such as noise level, location, and device status for each branch.
-
Product
Test Accelerometer Sensitivity And Noise Test
Accelerometer Test Unit
-
*Quick and Accurate Accelerometer Test*Battery operation*All tests use 32-bit resolution A to D Converter*All data downloaded to PC via Ethernet link*Records all data to a flexible easy to use database*Records time and date of tests
-
Product
Ultra-low Noise High Voltage Amplifier
WMA-200
-
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
Product
Pass-by Noise System
-
Vehicle Pass-by Noise TestingA very flexible Pass-by noise test system for characterizing the overall acoustic signature of any vehicle. Our solution brings a simpler, more effective and cheaper way to obtain accurate velocity and acceleration results for the Pass-by Noise test.
-
Product
Fast Low Noise SWIR InGaAs Camera
C-RED 2
-
C-RED 2 is a revolutionary ultra high speed low noise camera designed for high resolution Short Wave InfraRed imaging. Thanks to its state of the art electronics, software, and innovative mechanics, C-RED 2 is capable of unprecedented performances: up to 400 images per second with a read out noise from 10 to 30 electrons. Designed for high-end SWIR applications, smart and compact, C-RED 2 is operating from 0.9 to 1.7 μm with a very good Quantum Effi ciency over 70%, offering new opportunities for industrial or scientifi c applications.
-
Product
Low Phase Noise Reference Source
96270A
-
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
Product
Environmental Noise Monitors
-
Noise is one of the most complained about aspects of the environment, as not only does it have the potential to affect quality of life, it can also be difficult to monitor and therefore control. This type of noise is generally called environmental noise. There are many man-made sources of environmental noise, such as wind turbines, industrial sites, roads and traffic etc. If you are looking for equipment to measure noise in the workplace, look at sound level meters.
-
Product
Noise Dosimeters
Spark Family
-
Spark® series dosimeters are compact, affordable and tamper-proof personal Noise Dosimeter that measures the following to applicable IEC and ANSI standards:*Noise Exposure: Multiple Dose; Projected Dose; Time Weighted Average; (all with 4 user selectable combinations of Exchange Rate, Threshold, Criterion Level and Criterion Time); Sound Exposure Level*Sound Levels:; Leq; Lmax; Lmin; Lpeak/Luwpk, SEL and more*Time and number of events above Ceiling Level (115 dB) and Peak Level (140dB)
-
Product
Dual, Low Noise, Coaxial Cable Optimized
DCOAX
-
Very high precision, three-terminal capacitance measurements can be affected by the self-inductance of the test cables, mainly at higher capacitance values. Magnetically induced noise can also reduce the quality of measurements. The cable now offered by Andeen-Hagerling both minimizes these problems and provides a way to standardize the residual self-inductance.
-
Product
Noise and Vibration Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's unique Noise & Vibration Test Systems come fully equipped with the latest industry features. The on-screen operator display in our testers make it easy to set-up, read, track and record your noise or vibration information. We work directly with you to determine the best solution that will work for your application. Our data logging make sure that important data is stored and available for download for future reference. ESW's design engineers work to make sure the testing interface is easy for your operators to use. We work closely with our customers to make sure that your unique testing needs are met. Please see the slideshow below to see some of our Noise & Vibration Testers.
-
Product
Phase Noise Test System
PN9000 System
-
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
PC USB Noise & Vibration Measurement Systems
-
IEPE Sensor Based Measurement Systems, Charge Amplifier Based Measurement Systems, All-in-One Integrated Vibration Measurement Systems
-
Product
Noise Dosemeters
-
Noise Dosemeters are a type of sound meter designed to measure the levels of noise exposure to an individual over a period of time. All of our dosemeters are compliant to IEC 61252: 1993 / BS EN 61262:1997 and offer high quality and reliable personal noise monitoring solutions.
-
Product
Ultra-Low Noise 2 kHz Photoreceiver w/ Si-PIN Photodiode
PWPR-2K-SI
-
Picowatt Photoreceiver series PWPR-2K with switchable gain (10 to the 9th V/A, 10 to the 10th V/A) and a bandwidth from DC to 2 kHz is the perfect choice for cw-measurements, time resolved signal acquisitions and highly sensitive modulated measurements. Si and InGaAs models cover the wavelength range from 320 to 1700 nm.
-
Product
Vibration / Shock / Noise & Thermal Control
-
We specialise in vibration damping and shock isolation solutions for electronics and other light load applications.Our soft gel vibration damping materials are designed for isolating very light componets and extreme temperature environments.Most of our products are held in stock to support engineers with urgent vibration damping, noise control, shock isolation and cushioning impact problems.Our shock and vibration solutions are currently in use in aerospace, rail, truck, bus and handheld applications.
-
Product
Power Sensor and SNS Noise Source Cable (6.1m/20 feet)
11730C
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
Low Noise High Precision High Voltage Amplifier
WMA-280
-
The WMA-280 is a high voltage, low noise precision amplifier. Its specifications have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-280 can be used for MEMS actuation, EO-modulators, as high voltage driver for PZT (piezo) positioners, ultrasonics, and many other applications. Its output noise is only 300 microVolt rms.
-
Product
Noise Dosimeters
-
Noise Dosimeters are wearable, portable, wireless (cable-free), personal noise exposure meters for occupational and workplace noise measurements. They are designed specifically to monitor an employee’s noise exposure in order to comply with Health and Safety regulations.
-
Product
23 GHz Low Noise Amplifier
HMMC-5023
Amplifier
The HMMC-5023 is a GaAs MMIC low noise amplifier designed for moderate gain and low noise from 21 GHz to over 30 GHz. Typical applications of the HMMC-5023 include digital radio communications systems that operate within the 21.2 GHz to 23.6 GHz and 24.5 GHz to 26.5 GHz frequency bands. Moderate gain and low noise temperature make it ideally suited as a front-end gain stage.
