Noise Figure
delta of UUT noise to ideal.
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
Noise and Vibration Tester
-
SKF Condition Monitoring Center
High tech analysis and measurement such as frequency analysis (FFT) and further advanced analysis pinpoints faults. Spectral masks help to optimize the bearing performance in the particular customer application.
-
Product
IEC60335-2-9 Clause 3 Figure 104 Vessel For Testing Induction Hotplates
CX-104
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 104 Vessel for testing induction hotplates Parameter : Pot and lid material is mainly Q235, carbon mass fraction <0.08%; 2. The thickness of the wall material is 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm; 4. Pot body and lid surface to be clean 5, size: 110, 145, 180, 220, 300mm each one
-
Product
Noise Generators
GShM Series
-
*Operating temperature: +15...+25°C*Detection error for excessive relative noise temperature: +/-0.4 dB*Power consumption — <35 mA
-
Product
Precision Calibrated Noise Sources
-
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
Product
Low Noise Filter Adapter
PX0107A
-
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
-
Product
Noise Control And Acoustical Consulting Services
-
Our acoustical consultants use the latest and most advanced noise prediction and modeling software, precision sound measurement equipment and detailed acoustical analysis that enable us to help our clients achieve their project's noise requirements and goals. Contact us before your noise challenges become noise pollution problems.
-
-
Product
Phase Noise Analyzer
DCNTS
-
Noise eXtended Technologies S.A.S.
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences.
-
Product
Low Phase Noise Amplifier
-
RF Lambda’s lower phase noise amplifier offerings include special power supply conditioning and utilize technology to reduce the phase noise addition from amplifying the signal. Hermetically sealed options are available upon request.
-
Product
Portable 4-channel Noise & Vibration Analysis System
WCAmini AD-3661
-
* USB bus power unit * 24 bit, 4-channel measurement * A channel exclusively for tacho pulse measurements * WCAPRO (multi analysis software) * FFT analysis and real-time octave analysis * Tracking analysis and throughput recording/playback * Equipped with WCA Lite (easy-to-use analysis software)
-
Product
Noise Monitoring Station
HD2011NMT
-
HD2011NMT is a remote control Noise Monitoring Station with meteo parameters acquisition. It is designed to be part of a network of noise monitoring terminals or a stand alone unit.
-
Product
Phase Noise Measurement Solutions
-
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
Product
Noise Reduction Water Leak Detector
DNR-18
-
With digital noise reduction that removes intermittent sounds like barking dogs and passing vehicles. DNR-18: the advanced digital CPU eliminates intermittent interfering noises, like passing vehicles, people talking, and pedestrian footsteps.
-
Product
Low Noise Triaxial Cable
PX0102A
-
The Keysight PX0102A is suitable for low current measurement down to the sub-fA level. It supports the Keysight M9601A.
-
Product
8 Slot, 3U, PXI Chassis - Low Noise Fan
40-908-201
Chassis
This PXI chassis includes all the features and performance required by version 2.1 of the PXI standard and supports a control interface or embedded controller and up to seven more 3U peripheral modules. Mechanical expansion space on the right hand side allows the chassis to accept multi-slot modules, such as the BRIC, while only occupying one electrical slot.
-
Product
Sound & Noise Meters
-
Lutron Electronic Enterprise Co., Ltd.
portable, handheld instruments with calibrated microphones that measure real-time noise levels in decibels (dB), simulating how the human ear perceives sound
-
Product
Low Noise Amplifier
1010
-
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
Product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
High Power Noise Sources
NS-7001
-
The NS-7001 is high-power noise source specifically designed to operate in the 2.11-2.17 GHz UMTS band. It features flat output power that is regulated over a wide temperature range with high rejection outside the operating band of interest. Logic control is provided to enable/disable the noise source and an internal BIT function continuously monitors the output power. Other frequency bands and power levels are available.
-
Product
Environmental Noise Monitors
-
Our noise monitoring equipment is used across a wide range of applications and location. Each of these systems has been designed to meet the exact needs of the user by combining noise monitors with a software and support package.
-
Product
Sound Level Meter - For Workplace And Environmental Noise
SONIK-SE
-
The SONIK-SE is a powerful sound level meter which is ideal for performing occupational and environmental noise assessments for a variety of applications.
-
Product
Sound Level Meters & Noise Meter
-
Cirrus offers a range of Class 1 and Class 2 hand-held sound level meters and accessories to cover all noise measurement applications from simple noise tests to detailed noise analysis. Our range of Sound Level Meters and Noise Meters spans simple instruments that provide the measurement of Sound Level, Integrating-Averaging instruments that provide Leq and occupational noise functions as well as precision data logging sound level meters with 1:1 & 1:3 real time octave band filters and in-measurement audio recording.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Line Noise and Vibration Test Systems
-
The sound and vibration characteristics of your product can be used to identify many common mechanical and assembly defectives.
-
Product
Phase Noise Analyzers
-
Holzworth Instrumentation, Inc.
Holzworth's Real Time Phase Noise Analyzers are each designed to provide data faster than any other system, while maintaining data accuracy and repeatibilty. There is no guess work as to whether results are valid to the DUT or if there are unwanted variations or contributions coming from the measurement system itself.
-
Product
Noise Thermometer
MFFT-1
-
The MFFT-1 magnetic field fluctuation thermometer is a high accuracy thermometer system for typical dilution refrigerator temperature ranges.
-
Product
Ultra-low Noise Phase Inverter - Buffer
WMA-IB-LN
-
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
Product
Surface-Mount Noise Sources
-
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
Product
IEC61032 Test Probe 12 Figure 8
CX-12
-
Shenzhen Chuangxin Instruments Co., Ltd.
Test Probe 12 Figure 8 is intended to be used on appliaces for verifying the inaccessibility of hazardous live parts or hazardous mechanical parts.
