Filter Results By:
Products
Applications
Manufacturers
-
product
Silica Analyzer
SLIA-5000
Management of silica (SiO2) is paramount in preventing the formation of scales. This is because scales present in turbines will reduce the efficiency of power generation, especially for thermal power plants and nuclear power plants. By combining HORIBA's many years of track records and technological know-how, the silica analyzer has been reborn with conventional stability, reliability and maintainability.
-
product
Turbine Control Solutions
NRG’s turbine control sensors are engineered exclusively for the wind energy industry. These rugged yet simple devices consistently provide accurate wind speed and direction data. With a service interval of 10 years, you can rest assured that Hybrid turbine control sensors will perform as expected with minimal maintenance. Tens of thousands of NRG sensors are being used for turbine control around the world, including regions that experience the most extreme weather conditions in both hemispheres.
-
product
Magnetizer
MAGNET-PHYSIK Dr. Steingroever GmbH
Use our magnetizers for everything from the smallest rotors in a wristwatch to wind turbines. We magnetize magnets and magnetic materials of all sizes.
-
product
Lake Paddle Wheel Flow Meters
Operating much like a turbine flow meter, the paddle wheel flow meter consists of a freely rotating wheel which is outfitted with magnets on the blades or “paddles” of the wheel. As the fluid flows through the meter, spinning the wheel, sensors detect the magnets with each pass.
-
product
Engine Speed Control and Measurement (Test Set A)
MS 1100
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
product
Boroscopes
A Borescope is an optical tool used to view invisible areas without damaging an item.Borescopes are used for many devices in the industry. Hence its many benefits for example Turbine Engines,Internal Combustion Engines =,Pipes,Heat exchanger tubes,Gear boxes, and more.
-
product
Wind Sensors
FT742
The FT742 measures wind speeds up to 75 m/s. Its innovative design incorporates a series of “turbulators” which condition the air flow to deliver our highest levels of accuracy yet. Available in four mounting options, the Flat Front (FF) and Pipe Mount (PM) are typically used in wind turbine control and the Direct Mount (DM) in meteorological applications. The Surface Mount (SM) has been specifically designed for OEM integration and for use on UAVs/drones.
-
product
Custom Cable Assemblies
AMETEK Power Instruments has designed and manufactured electrical, thermocouple, and fiber optic harness assemblies for more than sixty years. We have the experience and capability to produce rigid and flexible harness assemblies for virtually any application, whether it is a missile ignition assembly, aircraft actuator assembly or a thermocouple harness for an industrial gas turbine. AMETEK Cable & Harness Products boast superior reliability, high temperature operation, numerous braiding options for abrasion resistance and EMI shielding, waterproof or environmentally sealed, and custom molding. For more information, please contact us.
-
product
Vibration Diagnostics System
VDS
The Vibration Diagnostic System (VDS) is a vibration data management system designed specifically for the machinery Predictive Maintenance (PdM) community. It harnesses the graphic display capabilities of Crystal Instruments EDM Software for the work of machinery vibration analysts. It allows the user to quickly get to the data for a machine of interest and displays that data in the familiar Tri-axial or Single Axis view. Users can quickly compare other data from the same machine, quickly navigate back into the historical data of the machine, and quickly compare the data to that of other machines in the database. The software supports the construction of Average (a.k.a. baseline) data for a class of machines and allows easy comparison to that data as well. A full suite of cursors designed specifically for PdM analysis is provided for inuitive user interaction with the data.In addition to great graphics, an extensible machine modeling system was developed specifically for vibration analysis. VDS allows users to model machines based on the elements of the machine that can contribute to the vibration energy of the whole. Model bearings, rotors such as motor bars, couplings such as flexible and fluid couplings, account for slip in fluid couplings, model gears and pulley systems, and model turbines by accounting for each stage. The system is wide open, users can create new elements to use within a system. Users that may not want to do all that are provided with a comprehensive library of machine components such as AC and Induction Motors, Couplings, Gears, Pulleys, Pumps, and other components. Single and double gear shafts allows users to model many kinds of gear boxes with an unlimited number of stages. This ability alone lets users model their machines to view and use to keep track of vibration pickup locations, record the forcing frequencies of each part of the system, and attach attributes such as manufacturer and other part information.
-
product
Aeroderivative & Heavy-Duty Gas Turbines
GE’s heavy-duty and aeroderivative gas turbines are efficient, versatile and reliable with individual output ranging from 34 MW to 544 MW. They are proven performers in simple and combined-cycle operation for pure power generation, cogeneration, mechanical drive, and waste-to-power.
-
product
Bat Deterrent Systems
As White-Nose Syndrome continues to ravage the populations of many hibernating bat species, the wind industry remains committed to lessening its impact on wildlife, including contributing to bat fatalities. While it is well researched that wind turbines cause mortality to bats, successful minimization methods have been implemented. Presently, the most effective techniques involve curtailment, which requires a reduction in energy generation. NRG Systems understands that this is not an ideal option for wind plant operators, so we have set out to develop Bat Deterrent Systems that could significantly reduce bat take without curtailment, meaning operators can produce more renewable energy more of the time while keeping all bats out of harm’s way.
-
product
Flow Meter Sensor
RF Pickups
SPECTEC Innovative Sensor Solutions
SPECTEC RF pickups are excellent for applications that require near zero speed and zero magnetic drag sensing characteristics, such as flow meter sensor applications. SPECTEC RF (modulated carrier) sensors have a long history of use in turbine flow meters and turbine engines in the aerospace, petroleum, chemical, pharmaceutical and food industries.
-
product
Heat Recovery Steam Generators
The heat recovery steam generator (HRSG) provides the thermodynamic link between the gas turbines and steam turbines in a combined-cycle power plant. Each HRSG solution is custom-engineered to meet your desired operating flexibility and performance requirements. With more than 750 HRSGs installed worldwide, GE is a world leader in supplying HRSGs behind all major OEM’s gas turbines.
-
product
Engine Test Systems
TITAN Engine
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
-
product
PDS Pile Placement Monitoring Software
The Monopile Placement module is the result of the cooperation between our clients and our engineering and software teams.Monopiles are used in wind farms as a foundation upon which to place a wind turbine generator. The application monitors the process of the placement of the monopoles.
-
product
Engine Simulator
MS 1118
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
product
Swirl Flowmeters
Swirl flow meters combine the measuring dynamics of turbine meters with the robustness and reliability of Vortex flow metering by requiring shortest upstream / downstream distances. Equipped with digital signal processing (DSP) and advanced filtering techniques, these innovative flow meters from ABB allow improved flow signal detection and provide measurement immunity from the effects of hydraulic noise and pipeline vibration.
-
product
Steam Turbines
Over the last 100 years, GE has delivered more than 1.2 TW of power production capability totaling over 41 percent of the world’s installed steam turbine base. With unparalleled global experience in engineering, manufacturing, sourcing, and services, we are delivering advanced technology steam turbine products to ensure our customers are more profitable, successful and satisfied than ever before.
-
product
Petroleum Distillate Tester
Weshine Electric Manufacturing Co., Ltd
Weshine invented Petroleum Distillate Tester(VS-9815 Series) is designed and manufactured in accordance with the standard of ASTM D86, which is applicable to determine quantitatively the boiling range characteristics of such products as natural gasoline, light and middle distillates, automotive spark-ignition engine fuels, aviation gasoline, aviation turbine fuels, 1-D and 2-D regular and low sulfur diesel fuels, special petroleum spirits, naphthas, white spirits, kerosines, and Grades 1 and 2 burner fuels.
-
product
Exhaust Gas Thermocouples
8TR4C Series
The AMETEK 8TR4C Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested, and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading older style Exhaust Gas Thermocouples.
-
product
Turbine Flow Meters
CT60, CT150
Flows up to 150 lpm (40 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
product
Wind Power Solution
ECO MITSUBISHI
The ECO MITSUBISHI is custom-made with firmware and fixtures designed specifically for Mitsubishi turbines: 1000, 1000A, MWT 2.4. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Capacitors - Power - Heavy Current (ESTA)
Vishay ESTA is one of the few manufacturers to offer a complete range of power capacitors. These cost-effective devices for harmonic control, energy savings, and voltage stabilization are highly reliable and environmentally safe, and can be used under the most rugged conditions. Vishay ESTA power capacitors address a wide range of energy-generation applications. Their “green” applications include energy generation in on- and off-shore wind turbines and solar power plants.
-
product
Resistive & Inductive AC Load Bank
RL
Resistive & reactive load banks are able mimic motor loads and electromagnetic devices within a power system as well as purely resistive loads by offering the ability to set a specific power factor (pf). Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit. JUNXY has an extensive range of resistive & reactive load banks to simulate these types of loads on a power source and the transformers, relays, and switches which will distribute the power throughout your facility.
-
product
Torsional Vibration Monitoring Systems
Advanced Telemetrics International
Are used for Noise Vibration and Harshness (NVH) testing and analysis in automotive drivetrain, wind turbine gearbox and various other applications where measuring or monitoring rotating vibration is important. These systems are used to transmit torsional acceleration from a rotating shaft or component, while the machinery is running.
-
product
Exhaust Gas Thermocouples
HYBRID Series
The AMETEK Hybrid Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading an older style Exhaust Gas Thermocouple.
-
product
Turbine Flow Sensor
2100
Engineered specifically for small diameter applications, the Signet 2100 Turbine Flow Sensor provides accurate readings in two flow ranges; 0.3 to 3.8 lpm and 3 to 38 lpm (0.1 to 1 gpm and 0.8 to 10 gpm).
-
product
Qualified Hermetic EGT Thermocouple Upgrade
FIT-IT & FORGET-IT Eliminate Exhaust Gas Temperature (EGT) thermocouple concerns with AMETEK's new EGT thermocouple product offering for Frame turbine applications. AMETEK has worked closely with the turbine OEM to design and engine test this thermocouple as a direct replacement and upgrade for all new and existing EGT thermocouples. The new EGT thermocouples are qualified and meet all design specifications.
-
product
Copper Strip Corrosion Tester
K582
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the corrosiveness to copper from automotive gasoline, aviation gasoline, aviation turbine fuel, lubricant oil and other petroleum products.
-
product
Turbine Flowmeters
Titan’s small turbine flowmeter range use a radial flow principle based on the Pelton wheel technique. This well proven method is the ideal way of measuring low rates of flow of low viscosity liquids. For these mini flowmeters, a jet of fluid is directed at a turbine that is mounted on robust low friction sapphire bearings. The geometry of the turbine and the fluid chamber ensures that the rotational speed of the rotor is proportional to the flow rate through the device. The use of this radial arrangement allows more energy to be imparted into the turbine, so the bearing drag is far less important. Furthermore, because more energy is available the bearings themselves can be a lot stronger so increasing the life of the flowmeter. For larger flows, some of the liquid can bypass the turbine chamber, which then behaves as a “shunt” to the metered fluid. Accuracy is still maintained and the output remains linear.
