RF Power Sensors
See Also: RF Power, RF Sensors, RF Power Meters, Rf Power Amplifiers
-
product
AC Current Sensor
LFR
The LFR ac current probe has been designed to have market leading low frequency performance, meaning low phase shift and low noise. This compact, low cost, clip-around probe is both flexible and dual-range, and is optimized to give minimal phase measurement error at frequencies from 45Hz to 20kHz and have a very low noise floor.
-
product
Power Amplifier
5241
The Model 5241 is a voltage-controlled power amplifier designed exclusively for Magtrol's Model HD-825 Hysteresis Dynamometer. Because of its double braking system, the HD-825 requires more than 4 amps of power in order to reach full torque. The 5241 (which can provide up to 5 amps of output current) is necessary in order to amplify the power between a 6200 or DSP6001 Controller (which both have a maximum current output of 1 amp) and the HD-825 Dynamometer.
-
product
Snap-on RF Current Monitoring Probe
TBCP2-250
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
product
Autoranging System DC Power Supply, 200 V, 70 A, 5000 W, 208 VAC
N8921A
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
product
Wattchman RF Station Monitor/Alarm Systems
81090
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
-
product
RF Device Tester
RF ITS
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
-
product
Request to Exit Sensor - Motion/Presence Sensors
Thermacon - Request to Exit Sensor, Concealed Passive Infrared Motion SensorA concealed and totally silent passive infrared (PIR) motion sensor that detects the presence of natural body heat and activates a relay. Relay activation begins when the detection area is entered and remains on for the duration of the preset relay timing. The unit is designed for concealed and easy installation in suspended ceilings. Four interchangeable detection patterns are standard with each unit. Units accept a power supply range of 12 to 24 volts AC or DC
-
product
Sensors And Cables
Sensors provide the vital link between the material under test and the instrument that measures its properties. Lambient Technologies LLC has developed a variety of disposable and reusable sensors for different applications. Click on the images below to learn more.
-
product
Mini Power, Contact, Receiver, 65 Amp, 8 AWG
610116112
Primary mating contact 610115124. (May mate with other ITA contacts, as well.)Mini Power contacts carry up to 65 amperes continuous current. Maximum resistance is 1 Milliohms.Specifications Operating Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BrassContact Plating 50µ" Au over 100µ" NiContact Termination SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 3.37
-
product
RF Adapters
RP-SMA Adapters
Are semi-precision units that provide excellent electrical performance from DC to 34 GHz and outstanding mechanical durability.
-
product
RF SCOE System
RF SCOE Systems require fast yet reconfigurable data processing as well as RF Modulation capabilities.For which FPGA Cards inside the PXI Frames are well suited.
-
product
CATV / RF Over Fiber
Transport RF signals: Cable TV (CATV), L-Band (SMATV), NTSC, DOCSIS, Return Path and other RF signals over 110km over a single fiber.
-
product
Solid State RF and Microwave Switches
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
-
product
RF Power Splitter, Combiner, Divider
PD2460
INSTOCK Wireless Components, Inc
Wideband Frequency (350 - 1000 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) Low PIM
-
product
Iveco Oxygen Sensor
KS60113 - Iveco
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Smart City Sensor
TrafiOne
FLIR TrafiOne is an all-in-one sensor for traffic monitoring and dynamic traffic signal control. The FLIR TrafiOne uses thermal imaging and Wi-Fi technology to adapt traffic signals based on the presence detection of vehicles, bicycles and pedestrians, even in total darkness or adverse weather. The sensor also generates high-resolution data for measuring travel times for different modes of transport and to improve traffic flows. TrafiOne also includes an HD video camera for additional visual support.
-
product
Photocell Sensor
AS6 220V 10A-B
Konstar Electric Industrial Co., Ltd
Photocell sensor switch can control the light switch automatically according to the light ray. When the sky become dark, the light will be on, but the day is coming, the light will off at once.It can used on the street lamps, stairs lamps, garden lamps etc.
-
product
Current Sensors
MCx1101 Family
Power architects are continually asked to push the boundaries for system efficiency, response time, small size, and low cost in new power system designs. Most modern designs require current sensors to help implement the complicated control, telemetry, and protection circuitry essential in meeting these difficult design goals.
-
product
Analytical Sensors
Conductivity sensors are pre-destined for use in the food industry. They detect the conductivity and concentration of different media and can differentiate between e.g. cleaning agents, rinsing water, and the food product. This means that it is not only possible to constantly track the product but also to reduce the waste of product and rinsing water – all possible without making adjustments to the sensor.
-
product
SafeOne RF Safety Monitor
The SafeOne is a RF Safety Monitor covering the requirements set forth in WHO ICNIRP specifications. It has a very wide frequency range covering 30MHz to 10GHz, which makes it suitable for use in almost all antenna installations. Due to the innovative lightweight design, technicians can wear this at all times, without the need to constantly be observant of the state of the instrument. The SafeOne is powered with standard batteries, with 250 days of continuous operation.
-
product
Digital and RF Testing
Amoeba® 5600
Built from the ground up based on AXIe and PXIe platforms, it offers the best of both worlds in terms of flexibility and power.
-
product
RF Bidirectional Amplifiers
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
product
LTE RF Communication Subsystem
The Delaire USA LTE RF Communication Subsystem is designed to provide a versatile solution for the testing needs of the next generation wireless systems. With the LTE test subsystem developers can build an end-to-end test environment for complete system operation. From end user equipment and eNodeB base stations to full system functionality, the LTE RF Communication subsystem allows developers to test and evaluate equipment and system performance in a controlled laboratory environment.
-
product
Automotive Oxygen Sensor
Model R-21A
Teledyne Analytical Instruments
Teledyne has a long and successful history in the development and supply of oxygen sensors for automotive emission testing equipment.The “R” series sensors are used by most automotive emission equipment manufacturers worldwide. We are striving to improve our sensors through aggressive research and development, assuring the highest quality products offered by any supplier of oxygen analyzers.
-
product
Temperature Sensor
The Temperature Sensor works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for Temperature Sensors and acquire synchronized temperature data.
-
product
Dielectric/Conductivity Sensor
VariconTM
The Varicon sensor is designed for use in presses, molds, bulk materials or laminates where a thin, flexible dielectric sensor is necessary. The Varicon sensor is thin enough to be implanted within a sample or between the plies of a laminate and may be discarded after use. Patterned on a polyimide substrate, the electrode array is designed to allow a choice of three sensitivities, which are selected by cutting off portions of the array at designated lines.
-
product
Vacuum Pressure Sensors
MKS, Granville-Phillips® Vacuum Gauges & Sensors cover a broad spectrum of vacuum measurement solutions.
-
product
hyperspectral imaging sensor
Hyper-Cam
The Hyper-Cam is a lightweight and compact hyperspectral imaging sensor which uses Fourier Transform Infrared (FT-IR) technology. This advanced high-performance spectrometer allows to detect and identify substances either gases or solids from a distance of up to 5 kilometers. It provides real-time chemical imaging as well as unparalleled spatial and spectral information about the IR targets under measurement.
