Thermocouple Simulators
-
Product
Partial Discharge Simulation Devices
-
Hangzhou Xihu Electronic Institute
Simulation device of cable PD faults, simulation device of switchgear PD faults, simulation device of GIS PD faults, simulation device of transformer PD faults.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PCI Express
PCIe-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
K Thermocouple Immersion Probe
TP741
-
Immersion "K" Type thermocouple probe. Stem diameter 1,5 mm.
-
Product
2 PRI + 4 Port FXS PSTN Simulator Adv
CH-4FXS-MOD-2PRI-A
-
One of the most feature rich PSTN simulator on the market. Unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Thermocouple 90 Series Modules
-
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
Product
Analog Simulator
MPLAB® Mindi™
-
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
K-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-K001
-
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Simulation Models for Passive Components, Transistors, Diodes, etc.
-
An indispensable collection of the industry''s most advanced simulation models for passive components, transistors, diodes and more. These reliable, measurement-based models maximize the RF/MW electronic design automation (EDA) process, reduce design cycle times, and lower product development cost. With a few EASY steps, the Modelithics Model Libraries are ready to use in EDA tools.
-
Product
Barometric Pressure Simulation
SimBARO
-
Embedded and Integrated GPS/Inertial navigation systems require an altitude reference data input provided by a barometric pressure altimeter to reduce vertical plane errors inherent within inertial systems. Spirent’s SimBARO product offers a simulated source of barometric pressure altitude data and is available as an add on to SimINERTIAL, Spirent’s Inertial Measurement Unit (IMU) and Embedded GPS/Inertial navigation system (EGI) test tool.
-
Product
2 Port 10/100/1000Mbit/s AFDX®/ARINC664P 7Test, Simulator And Monitor Module For XMC
AXC-FDX-2/B
Monitoring Module
AFDX®/ARINC664P7 Test and Simulation module for XMC with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
Product
High Output Simulators
-
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
Product
Solar Cell Simulation
Setfos
-
Setfos excels in analyzing and fitting experimental data, providing researchers with valuable insights and trend predictions. Complement your experimental work with Setfos for unmatched accuracy and reliability in data interpretation.
-
Product
MIMIC® IoT Simulator
-
The MIMIC IoT Simulator creates a real-world test lab with many thousands of manageable IoT sensors, gateways and other connected devices to simulate your IoT environment related to*Industry 4.0*Smart Factories*Smart Cities*Smart agriculture
-
Product
MEMS Sensor Simulation
SimSENSOR
-
Performance testing of sensor fusion in MEMS inertial and multi-GNSS navigation systems. SimSENSOR extends the capabilities of Spirent’s multi-GNSS simulators by simulating MEMS sensor outputs on a common trajectory with the simulated GNSS RF signals. The simulated MEMSs sensor outputs include user control of representative noise and errors (bias/drift).
-
Product
AC drives, Soft-Starters or Servo Drives Simulation Software
-
Product simulation software enables users to operate, program and simulate AC drives, Soft-Starters or Servo Drives directly from their computer without having the actual product present or connected. Our simulation software can be used as a demonstration tool during a sales meeting or as an interactive tool for training classes. Software available In addition we offer simulation software for dedicated markets such as pumping, mining, material handling, etc... to demonstrate the use of motor controls in simulated applications.
-
-
Product
Thermocouple (K-Type) And Temperature Probe Adapter
U1186A
Temperature Probe Adapter
Consists of a K-type thermocouple bead and a mini connector to dual banana plugs.
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
-
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Thermocouple Power Sensors
N8482H
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Handheld ESD Simulator
-
Battery operated handheld ElectroStatic Discharge (ESD) generator up to 30kV.Discharge networks according to IEC 61000-4-2, ISO 10605, MIL-STD-461 CS118, DO-160 section 25 and many more standards.
-
Product
Modular Solar Array Simulator Mainframe, 1200W
E4360A
Mainframe
The Keysight 1200W, E4360A Modular Solar Array Simulator is a 2U high, 2-slot mainframe that accepts up to 2 E4360 series modules. Modules are ordered separately. It offers LAN, USB, and GPIB interfaces standard.
-
Product
Multi-Parameter ECG Patient Simulator
SL-8 SimSlim®
-
The smallest, comprehensive multi-parameter patient simulator on the market. Includes ECG, Respiration, Arrhythmia, 4-IBP, YSI 400/700 Temperature, and Cardiac Output. Its patented power circuitry provides amazing battery life up to 10 years without charging or changing batteries! One button operation reduces the time for setup and completing testing. View the product manual on our User Manuals page.
-
Product
Basic Rate ISDN and IDSL Network Simulator
Emutel Solo
-
Emutel Solo is a small, portable lightweight battery powered basic rate ISDN and IDSL network simulator. With 2 software switchable S/U interfaces and the choice of either Euro-ISDN, North American or NTT support. Emutel Solo allows you to test and demonstrate all types of BRI equipment on one compact unit. Providing all the standard features but also many others that its compeditors don't include.
-
Product
Regenerative Grid Simulators 9kVA-15kVA
-
Chroma Systems Solutions, Inc.
Four quadrant, single- or three-phase AC power sources designed to simulate real-world grid characteristics for EV, PV inverter, and smart-grid test applications.
-
Product
4 Port Phone Line Simulator (FXS) Adv
SIM-4FXS-A
-
This unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Two Inputs Thermocouple Thermometer
HD2328.0
-
Thermocouple thermometer for probes type K, J, T, E. It measures temperature by means of immersion, penetration, contact or aria probes. Two inputs for miniature thermocouple connectors. Storage of maximum, minimum, average value. Functions: REL, HOLD and auto power off which can be disabled, IP 67 protection degree.
-
Product
STANAG3910/EFEX Test And Simulation Module for Standard Ethernet
ANET3910
-
STANAG3910/EFEX Test and Simulation module for Standard Ethernet. The ANET embedded Linux Operating System gives the unique capability to run the optional PBA.pro Engine right in the box. Another option is the ANET-ADK onboard software development kit where users create run-time applications (e.g. STANAG3910/EFEX to Ethernet Converter, STANAG3910/EFEX to Ethernet Gateway) to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available.The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
