-
Product
CANbus Network Tester
-
Automatic Pin Test - automatically checks any abnormality on the OBD2 port caused by shorting (i.e., Pin 16 Power shorted to Ground), reverse polarity, and any other abnormalities
-
Product
LXI WTB Probe, Thru connect, DC coupled
60-981-001
-
The 60-981 LXI Wired Trigger Probe provides a simple method of monitoring the LXI Wired Trigger Bus activity. It provides a through line active probe that can be used to non-intrusively monitor the waveforms of the M-LVDS drivers on all 8 channels. Each channel has two single ended outputs from the differential pair that can be subtracted by an oscilloscope to display each driver output and the differential signal.
-
Product
Network Attached Storage & Recorders
-
Curtiss-Wright Defense Solutions
Our encrypted, solid-state network-attached storage (NAS) subsystems are designed to reliably provide file services to clients on an Ethernet network in a harsh environment. These NAS solutions protect data-at-rest (DAR) with the industry’s first NIAP Common Criteria (CC) certified 2-Layer encryption, as well as an option for NSA Type 1 encryption.
-
Product
DC Coupled, 14-Bit Digitizer For ExpressCard 54, 2 Channels 150 MS/s
EC14150D
-
The EC14150D (EC) is an DC-coupled dual channel waveform capture board that provides a remarkable combination of high speed and high resolution sampling along with a very large memory capacity all in a very compact and low power consuming ExpressCard form factor. At 4.5 W, the EC represents one of the lowest power consuming digitizer cards ever created for its class. Signal frequencies up to 200 MHz can be accurately captured either in baseband or in higher order Nyquist zones using under-sampling techniques. Where DC-coupling is required, the EC14150D should be considered.
-
Product
PNA Microwave Network Analyzer
N5222B
Network Analyzer
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Network Cable Tester
AudioJoG Pro 8 Power
-
Audio/Lighting/Network cable tester with SINGLE & DOUBLE ended testing with memory and intermittent fault detection.
-
Product
USB And Network Cable Tester
PinMaster PK-2018/2020
-
The PinMaster is designed to quickly and easily check all types of USB cables (USB 2.0, 3.0, A, B, 2.0 mini B and 2.0/3.0 micro B) and common cabling system includes Network/Data, Telephone/Voice and Coaxial/Video cables.
-
Product
Networked Absolute Inclinometer
T7
-
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
Product
Cable and Network Testing
-
Network technicians, Network Managers, and System Installers need their twisted pair cabling system to reliably support Ethernet applications up to 10GBASE-T. Efficiently solving network connectivity problems, installing PoE devices, and managing network move, adds, and changes is essential in today’s fast-paced IoT centric environment. Fluke Networks Cable + Network Testers enable users to build and maintain their connected infrastructure.
-
Product
Network Communication Platform Peripheral
-
Axiomtek provides different add-on cards for network appliance, such as PCIe PoE cards, network security cards, IPMI and more.
-
Product
40 GbE Network Attached Storage
HSR40 AC
-
Curtiss-Wright Defense Solutions
Handling the incoming data is Curtiss-Wright’s CHAMP-XD2, featuring dual Xeon D processors and two built in 40 GbE interfaces. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data. By keeping the data as PCIe, instead of converting it to SATA and sending it to a SATA storage, the data can be directly pipelined over the backplane to the PCIe-based Non-Volatile Memory Express (NVMe) SSDs.
-
Product
Avionics Network Simulation Systems
-
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
Product
Vector Network Analyser
LA19-13-02
-
The LA19-13-02 is a PC-driven Vector Network Analyser suitable for measuring a wide range of devices from 3 MHz to 3 GHz with 100 Hz resolution. Its full s-parameter test set includes bias-Ts for biasing active devices. It is housed in a small lightweight package making it very portable.
-
Product
Network Cable Tester
AVJoG
-
*A two box solution to testing AV panel installations. *Each box only 150mm square.*Easy to use with only one button operation. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *6V battery or Mains use.
-
Product
Network, Port ID And Cable Tester
One for All PH-400
-
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
Product
CAN + OBD Network Data Converter
NC1
-
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
Product
Wireless Network (loT)
-
Are computer networks that are not connected by cables of any kind. The use of a wireless network enables enterprises to avoid the costly process of introducing cables into buildings or as a connection between different equipment locations.
-
Product
Impedance Stabilization Networks
ISN
-
They are required for the measurement of conducted common mode noise on Telecom Cables of Information Technology Equipment (ITE). These measurements are necessary to meet the requirements specified in CISPR 22 and CISPR 32 standards.
-
Product
Network Testing Portfolio
TEMS™
-
The TEMS™ Network Testing Portfolio allows you to optimize the quality of your mobile network by concentrating on user experience. TEMS gives you the ability to walk test, drive test, and dynamically analyze your mobile network under the real-life conditions your users experience—indoors, outdoors, and around the clock.
-
Product
10GbE Network Attached Storage
HSR10
-
Curtiss-Wright Defense Solutions
The High-Speed Recorder 10 (HSR10) is a network attached storage (NAS) device designed for high-speed network recording based on a double 10 Gigabit Ethernet (GbE) port layout. What’s more, to adhere to security requirements for mission-critical applications, this unit is designed with two-layer encryption and follows industry-standard NAS protocols permitting system design flexibility.
-
Product
Compact Networked I/O
-
We offer networked I/O devices based on Ethernet, DeviceNet™, and Profibus for industrial control and automation applications.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Charge Coupled Device (CCD) Standard Image Sensors
-
Teledyne e2v is the leading supplier of scientific grade Charge Coupled Device (CCD) image sensors for the most challenging low light imaging and spectroscopy applications.
-
Product
Network Automation Manager
-
Integrated network automation software for large or complex environments
-
Product
Next Generation Network Testing
UX400
-
The VeEX UX400 is the smallest multi-service transport test solution to offer test capabilities ranging from DS1/E1 all the way up to 6x 100G traffic generation, supporting the latest 100G/40G optical pluggable form factors (CFP4, CFP2, CFP, QSFP28, QSFP+, no adapters required). Its modular architecture allows for up to six independent test modules and up to twelve concurrent tests or combinations of tests, including legacy PDH/DSn, SDH/SONET, OTN, Ethernet, Fibre Channel, CPRI/OBSAI, C/DWDM spectrum analysis and more. The platform's software architecture has been developed so that multiple users or scripts are able to access and operate different test modules at the same time, maximizing the use of resources. A battery backup option is available for the portable UX400 platform. Test modules can also operate in a standard 19" rack – the UX400R, when portability or battery operation is not needed.
-
Product
CNC Machine Network Solution
WebAccess/CNC
-
Webaccessoryess/CNC supports diverse SCADA drivers, CNC, I/O, PLC devices for efficient equipment data collection & networking app development.
-
Product
Industrial Ethernet Network
CC Link IE Field
-
CC-Link IE Field network is the first gigabit industrial Ethernet network extended down to the field device level. It combines the best of existing technologies and applies them in a highly reliable architecture that provides exceptional data bandwidth and transaction rates. The new network uses commercially available Cat5E cable and RJ45 connectors.
-
Product
PNA-X Network Analyzers
-
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
Product
Network Monitoring Tool
-
Motadata’s proactive network performance monitoring tool can be used to automatically discover network devices, interfaces, and applications. The network monitoring software in a multivendor IT environment ensures complete visibility of IT infrastructure. The unified view enables IT admins with a comprehensive picture of the overall IT health and also provides drill-down root-cause analysis, enabling them to resolve network issues even before they affect business processes. It facilitates monitoring of hybrid multi-vendor environment using 100+ pre-defined monitoring templates with immediate notifications on the set threshold values.
-
Product
Network Peripheral
-
PLANET provides a variety of network peripheral devices to help create an efficient network environment. This product line includes enterprise IP KVM switches and IP power manager for data center management, digital media center, IP HDMI extender and NAS.
