Process Calibrators
Assure process control signal validity.
-
Product
Process Counters
TCT201-2ABC
-
The Process Counter TCT201-2ABC is a 1/16 Din 48 x 48 mm panel mount programmerable digital Counter with two 8 Amp relay outputs and up to 3 inputs. The TCT201-2ABC also has a potentiometer input that can accept either 5K or 10K Potentiometers. Other inputs can be PNP or NPN switches, 2 or 3 wire Proximity switches.
-
Product
Post-Diffusion Process Control
Suns-Voc MX
-
Perfect for paste-firing optimization and process control. Open-circuit method indicates the upper bound of efficiency for any solar cell precursors
-
Product
Energy & Process Monitor
-
Real time monitoring and reportingComposite system with EMS and PEMSDesired reports like, Doff wise, shift wise, count wise, production, energy, UKGSpeed Vs Kw curve, trends, bar graphs, comparisonsAlerts on higher UKG, lesser production, utilization & power fluctuations.Maintenance alerts based on run hours production cost analysis - Cost Audits - Energy Audits
-
Product
Radiation And Process Monitoring Systems
ProTK
-
Monitoring of the main steam line for leakages in a PWR nuclear power plant with a wide-range gamma ionization chamber.
-
Product
Process Timers
TCT101-1ABC
-
The Process Timer TCT101-1ABC is a panel mount 4 digit 2 line display meter that can be set up for various Timer functions, such as Timer Off, Timer On, Pause Timer, Timer On and Off, Propotinal Timer. The TCT101-1ABC has 2 relays that can be used for various functions and has 5 Amp contacts. The timer periods can be set in multiples of 1 hundredths, 1 tenths of a second, seconds, minutes or hours. With the aid of the front touch panel or digital input it is possible to interrupt the timer. The unit also has a function that can set the output to toggle on and off over a period of time.
-
-
Product
Calibrator Module
CAP CAL
-
The purpose of CAP-CAL is to check the correctness of Tan Delta and Capacitance of TD 5000 and TDX 5000. The calibrator includes an extremely high accuracy high voltage capacitor, which comes with a certificate issued by ISA - Altanova Group lab.
-
Product
Signal And Image Processing Research
-
TPAC solutions are ideal for research in signal processing applied to ultrasound. You need to be able to access to any parameter, implement a particular algorithm, and access to any data during the acquisition or postprocessing phase. TPAC provides you all of these. It can be applied to studies in signal processing, image processing, beamforming, machine learning, etc… Thanks to TPAC’s open platforms, you will be able to freely set the ultrasonic sequences, record the raw data from your experiment, and test your own algorithms or even method. In order to adapt to a wide variety of habits, TPAC proposes multiple APIs (Application Programming Interface) compatible with Matlab, C++, Python, C#, Labview and working under Windows or Linux operating systems. Through a socket, it is even possible to use any OS of your choice.
-
Product
Calibrator for Battery Charger-Analyzers
VCM-100
-
The VCM 100 is an instrument designed to verify the performance and to calibrate Battery Charger-Analyzers used on Nickel-Cadmium, Lead-Acid and other types of batteries.
-
Product
Calibration and Repair
-
Traceable vibrometer calibration insures a high level of data quality, critically important for many applications in industry, science and medicine. Polytec service engineers ensure fast and efficient equipment calibration that is traceable to national and international standards, intended to be ISO/IEC 17025 compliant.
-
Product
Pressure Controllers for Flowing Processes
-
Alicat Scientific, Incorporated
Use pressure controllers when gas is flowing through a process. They control absolute, gauge, or differential pressures, and can measure in-line pressures or be plumbed to measure process pressures at any point.
-
Product
Waveguide Calibration Kits
-
Designed to provide accurate calibration of vector network analyzers (VNAs) that are used for measurements in standard rectangular waveguide from 2.6 to 50 GHz (WR284–WR22).
-
Product
Differential Calibration Substrates
-
The GGB Industries, Inc., line of DIFFERENTIAL CALIBRATION SUBSTRATES allows the user to calibrate any GGB Industries, Inc., microwave Picoprobe at the probe tip. The underlying principal of the calibration of a measurement system is to provide accurate known standards to which the measurement system can be connected.
-
Product
Calibration Services
-
Trescal US is accredited to ISO/IEC 17025, ANSI/NCSL Z450-1 and ANSI/NCSL Z540.3 through A2LA. Trescal has one of the largest scopes of accreditation in the country for electronic, physical and dimensional domains as well as being a factory-authorized service center for many International manufacturers.
-
Product
Calibration Pulse Processor
2401
-
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
Product
Process Control Actuators
SM-6000
-
*Torque range up to 35,256 Nm (26,000 lbf.ft)*Up to 313° rotation*Double O-ring sealing*Continuous unrestricted modulating duty*Manual override standard*HART®, Profibus® & Foundation Fieldbus® available*Automatic torque limiting*Self-locking drive system to hold in last position and prevent backdriving up to 125% of torque rating*AC input power (1-phase and 3-phase)*Temperature range from -40° F to 185° F (-40° C to 85° C)*Manual override standard
-
Product
Repair & Calibration Service
-
Repair and calibration facility is one of the nation's premier laboratories that deals exclusively with electronic test and measurement equipment.
-
Product
Resist Processing Systems
-
The EVG100 series resist processing systems establish new standards in quality and flexibility for photoresist coating and developing. Designed to provide the widest range of process variations, the EVG100 series’ modularity offers spin and spray coating, developing, bake and chill modules to suit individual production requirements. These systems accommodate the processing of an extensive range of materials such as positive and negative resists, polyimides, double-sided coating of thin resist layers, high viscosity resists, and edge protection coatings. These systems can handle more than one substrate size, from 2" to 300 mm diameter, rectangle, square or even irregular shaped substrates, with no or very short tooling time. This allows the development of new devices or processes on an industrial level, which not only requires high flexibility but also controlled and repeatable processing. EVG has built up many years of spin and spray coating experience for demanding applications and incorporates this knowledge into the EVG100 series, where our process know-how can be leveraged to support our customers.
-
Product
Intrinsically Safe Calibrators
-
We offer calibrators that are Intrinsically Safe and can be used in hazardous Ex areas, where explosive gases may be present. Using Ex certified calibrators makes it easier for you, as it eliminates the need for always getting hot-work permits when going on site. Our Ex calibrators are both ATEX and IECEx certified.
-
Product
Process NIR Analyzers
-
Process near-infrared (NIR) analyzers continuously measure moisture, oil, coat weight and other parameters directly in manufacturing processes for responsive process control. Common industries include wood products, tobacco, snack foods, converting, and bulk materials. A variety of sample interfaces, environmentally rated enclosures, and interface options are available for easy implementation and integration.
-
Product
Calibration Services
-
A calibration industry leader since 1962, SIMCO provides trusted, high-quality instrument calibration services for thousands of organizations, including 15 of the top 20 global biomedical device manufacturers and 14 of the top 20 global aerospace and defense manufacturers.
-
Product
Multiport Calibration Assistant
S95552B
-
The S95552B software application flexibly creates and manages calibration sets for multiport measurements. This software enables you to combine multiple calibration sets with independent test ports as one calibration set with a greater number of test ports. The software also offers a way to re-calibrate using a certain set of test ports to refresh the calibration set.
-
Product
PSD Signal Processing Tool
SEEPOS
-
For most position measurement applications the SiTek SEEPOS system offers a complete and easy-to-use solution. High speed PSD electronics combined with digital signal processing and high speed USB data transfer gives a powerful measurement system. With its large dynamic range it can handle light powers from nW to mW from DC light sources as well as modulated light sources. All parameters, such as PSD bias voltage, amplifier gain, the use of analog and digital filters etc., are easily controlled from the included software and light spot position is continuously displayed both in XY and X-t, Y-t graphs. Optimized plot algorithms ensure that all data is visually seen on the screen even in full speed measurements. Included tools for data analysis and visualization simplify rapid scan through large data sets in order to find specific parts of interest.
-
Product
Loop Calibrator
6500 LC
-
Standard Electric Works Co., Ltd
● 4-20mA (1kΩ load, 24V Loop Supply).● 0.025% Basic Accuracy.● Simple Operation Interface.● Auto Ramp and Step Functions.● 0-20mA, 0-24mA selectable.● Incremental percentage setting : 0-100%.● Warning beeper when output is open.● 0-24V output.● The minimum load of 20kΩ on voltage mode.
-
Product
Process Monitoring and Control Systems
ComoNeo and ComoScout
-
Consistent digitization increases product quality and cost-effectiveness in injection molding production. The ComoNeo and ComoScout process monitoring system ensure that both newcomers and experienced users can monitor and control their processes precisely and efficiently.
-
Product
HiPot Calibrator
Model 9102
-
The 9102 Hipot Calibrators is specially designed standard devices for instrument calibration lab. The 9102 can simulate multiple loads and apply to various Hipot testers. These calibration equipment can save manufacturers a great deal of regular calibration fee.
-
Product
Calibration
Field Probes
-
We calibrate following types of field probes:Electric field probesMagnetic field probesFlux density metersRadiation monitorsNear field probes
-
Product
IADS Data Processing
-
Curtiss-Wright Defense Solutions
The IADS Server is the data processing, delivery and archiving portion of the IADS software suite. It supports a wide range of data source interfaces and can serve hundreds of concurrent client connections. It can process hundreds-of-thousands of parameters with comprehensive data storage capabilities and real time data recall for client scroll back.
-
Product
High Current Calibrator
MC151
-
MC151 Current calibrator is an accurate current source capable of 120 A. Typical uses include calibration of current sensors, current probes, current transformers, shunts, ammeters, DMMs or as stable current source for test and development applications. The calibrator is equipped with a built-in multimeter that can be used for simulation of programmable transconductance or current amplifier.
-
Product
Processing And Data Recorder Systems
DAQStream
-
DAQStream is a family of high-performance data acquisition and processing systems that combine Delphi Engineering Group’s industry leading wideband digital receivers and StreamServer™ – multi-channel, streaming software for unparalleled high-speed data recording and processing performance. Delphi’s wide variety of FMC, FMC+, ADC and DAC modules enable DAQStream users multiple configuration options to meet the most stringent application requirements.
