-
Product
PRO Conductivity Meter
MW301
-
MW301 is a Portable Conductivity (EC) Meter with Automatic Temperature Compensation. This instrument has been designed to meet the Grower's need for equipment suited to the aggressive environments found in agricultural and hydroponics applications.
-
-
Product
Carbon Sensor Conductivity Meter High-Concentration
HE-960HC
-
FPD manufacturing processesThe HE-960HC measures conductivity, which forms the basis for parameters in chemical and waste water management. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960HC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
Product
Thermitest
THW-L2
-
Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For Low-concentration)
HE-200C
-
HE-200 connects conductivity sensor (ESH/FS Series) and measures conductivity and temperature in the sample water. It is suitable for monitoring pure water/boiler water drainage recovery control and inline measurement of pharmaceutical water conductivity according to USP<645> quality guidelines.
-
Product
Conductivity Meter
Cond 6+
-
Multi-Point Push-button Calibration (up to 5 points) with ±1% full scale accuracy :: Option of quick, easy automatic calibration or customised, near-to-sample manual calibration.
-
Product
PRO High Range Conductivity Meter
MW302
-
MW302 is a Portable Conductivity High Range (EC) Meter with Automatic Temperature Compensation. This instrument has been designed to meet the Grower's need for equipment suited to the aggressive environments found in agricultural and hydroponics applications. It is also a great meter for food, labs, and water treatment applications.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For High-concentration)
HE-200H
-
HE-200H connects conductivity sensor (FES-125F,126F) and measures conductivity and temperature in the sample water. It can be used not only for measurement of electrical conductivity in aqueous solution, but also for concentration adjustment and rinse monitoring of CIP, etc., as well as for concentration monitor of process.
-
Product
Panel-mount Type Conductivity Meter (Four-Wire Transmission, For Wide Range)
HE-960HI
-
HE-960HI is a wide-range type sanitary electric conductivity meter that can measure over a wide range from manufacturing water up to 500 mS/cm, and enables advanced concentration management through abundant outputs. It connects conductivity sensor (FES-220/310). Cleaning-in-Place (CIP) terminal management and a reduction in cleaning solutions is also achieved through accurate surface detection.And we have developed a lineup of electric conductivity sensors that can be used in conjunction, from the conventional insertion type to the flow-through type with improved cleaning and sanitary properties.
-
Product
PH and Conductivity Meters
-
PeakTech Prüf- und Messtechnik GmbH
It is possible to measure the conductivity of liquids, for example of water. The purer the water, the lower the conductivity (for example, distilled water is purer than normal water and has a low conductivity of approx. <10 µS).
-
Product
100Hz/120Hz/1kHz Handheld LCR Meter
U1731C
-
Now you can measure at frequencies as high as 100 kHz, a capability that is typically found only in benchtop meters. With the auto identification, Ai which conveniently displays component type and detailed component analysis such as Z, ESR, DCR, you can get measurements done faster. Better yet, the battery lasts up to 16 hours, ideal for testing on the go. With the U1730 Series, you can perform quick, basic LCR measurements at your convenience, without burning a hole in your pocket.
-
Product
EPM Series Single-Channel Power Meter
N1913B
-
The N1913B EPM series single-channel average power meter provides repeatable and reliable results for bench/rack and field applications.
-
-
Product
P-Series Dual Channel Power Meter
N1912A
-
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
Product
Digital Power Meter
66205
-
The 66205 is the 2nd generation of the 66200 series power meter designed specifically for single channel measurement. Its state of art design is capable of providing highly accurate power measurements to meet the requirements of IEC 62301/EN50564 standards. Functionality improvements of the 66205 increase power measurement capabilities to a wider range of applications. The Smart Range function is one of the most important new features added to the 66205 power meter. Smart Range allows the power integration mode to perform active power measurements with the measurement range in auto mode. Chroma’s proprietary design automatically selects the appropriate range, based on changes in sensed voltage and current, ensures the best accuracy when integrating the measurements over time. The 66205 provides 10 selectable current measurement ranges from 5mA up to 30A. External sensor options A662017~A662020 are available to increase the current measurement range. Six selectable voltage ranges are available up to 600V.
-
Product
Optical Power Meter - PXI
Power 1400 Series
-
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
Product
Precision LCR Meter 20 Hz to 300 kHz/500 kHz/1 MHz
E4980AL
-
The E4980AL precision LCR meter is an industry standard LCR meter that provides the best combination of accuracy, speed, and versatility for a wide range of component measurements. The frequency upgrades provide a solid investment option and asset utilization.
-
Product
LCR Meter 10Hz - 300 kHz High Precision
T3LCR1300
-
LCR Meter 10Hz - 300 kHz High Precision.
-
Product
Inline Optical Power Meter - MATRIQ
Power 1600 Series
-
The Power 1600 Series optical power meter provides quick and accurate inline power monitoring from -50 dBm to +20 dBm with 1, 2 or 4 channels in a compact form factor.
-
Product
Handheld Capacitance Meter
U1701B
-
Capacitance meters do not always need to be on the bench. Neither do they always need to strain your budget. Keysight's new U1701A capacitance meter now puts the capacitance meter into the palm of your hand while doing random checks across the production floor or performing checks at your inspection or sorting stations. With wide measurement range, and features to ease your sorting tasks, the U1701A puts a new level of convenience into the world of capacitance meters.
-
Product
Inline Optical Power Meter - PXI
Power 1600 Series
-
Quantifi Photonics’ Power 1600 Series inline optical power meters provides quick and accurate inline power monitoring. Seamlessly integrate the power meter into your new or existing PXI test setup and save space, lower your costs and improve testing efficiency.
-
Product
Analog Optical Power Meter - MATRIQ
1500 Series
-
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
Product
100Hz/120Hz/1kHz/10kHz Handheld LCR Meter
U1732C
-
20,000 counts resolution0.2% accuracy Wide LCR ranges with 4 selectable test frequencies (100Hz, 120Hz and 1kHz and 10kHz)Auto identification(Ai) which automatically determines and displays component type and measurements Detailed component analysis with ESR, Z, D, Q, functions Battery life of 16 hours/Ac-powered IR-to-USB connectivity for data logging to PC
-
Product
Optical Head Interface
N7749C
-
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
Product
Capacitance Meter
E4981A
-
The E4981A capacitance meter offers a high-speed with reliable measurements for ceramic capacitor testing in the production lines. The E4981A realizes the measurement capabilities of capacitance from small to large values with accurate measurements. The E4981A capacitance meter contributes improvements of the test throughput, while attaining excellent component quality for ceramic capacitor testing.
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
-
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
P-Series Modular Power Meter (LXI Compliant)
N8262A
-
The Keysight N8262A P-Series modular power meter enables LAN-based automated measurements of peak, peak-to-average ratio and average power. The N8262A enables fast, efficient, and cost-effective creation and reconfiguration of your ATE system. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
-
Product
PXIe-4190, Up To 2 MHz, Up To 40 V PXI LCR Meter
788101-01
-
The PXIe-4190 helps you measure and test the inductance, capacitance, and resistance (LCR) of electronic equipment. It includes an LCR meter with fF-class capacitance measurements and a precision source measure unit (SMU) with fA-class current measurements. You can use PXIe-4190 meter in capacitance-voltage/current-voltage (CV/IV) automated test systems for semiconductor applications including integrated passive device (IPD), microelectromechanical systems (MEMs), multi-layer ceramic capacitor (MLCC), and parametric testing. Additionally, the PXIe-4190 is supported by the NI-DCPower instrument driver, which includes APIs for LabVIEW, C, C# .NET, Python, and other programming languages.
-
Product
Optical Power Meters
-
Fast monitoring of optical signal power from -60 to +10 dBm across 750 – 1700 nm wavelengths. The 1500 Series power meter offers logarithmic analog output which is ideal for active fiber alignment.
-
Product
Optical Multiport Power Meter
N7745C
-
Keysight's popular N7745A optical power meters with eight power-sensor channels provide increased throughput and operational efficiency to meet today's challenges in manufacturing. Designed for characterizing optical multiport components, these optical power meters offer industry-leading solutions for device connectivity, high-speed measurement data acquisition and fast data transfer for post-processing. The multiport power meter enables fast measurement solutions for all multiport devices; for example multiplexers, PON splitters, wavelength selective switches (WSS) and ROADMs, as well as compact setups for simultaneous testing of multiple single-port devices.
