Relay Drivers
Control the energized state of relays.
-
Product
Measuring and Monitoring Relays
-
Various measuring and monitoring relays are available for the purpose of monitoring electrical quantities. In addition to overvoltage, undervoltage, frequency, unbalance, phase sequence, phase failure and loop monitoring, special solutions for specific applications are also possible: extended temperature ranges, sector-specific standards, compact design, country-specific profiles.
-
Product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector, With Interlock
42-158-104-HI
-
The 40/42-158-104-HI is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via a 37-pin D-type male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors
40-153-002
-
The 40/42-153-002 is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
High Current 45 Relay PXI Card
GX6315 Series
-
The GX6315 is a 45 channel, high current relay board that plugs directly into any 6U PXI slot. The GX6315 also provides nine transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
-
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
General Purpose Reed Relays, Dry and Mercury Wetted
Series 89
-
Mercury wetted relays - 0.1 inch x 1.0 grid. As series 80 and 88 but with alternative pin configuration
-
Product
Half, Full Bridge & Three Phase Drivers
-
Renesas' half-bridge (h-bridge), full-bridge and three-phase drivers handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance.
-
Product
Laser Diode Drivers (LDD)
-
LDD technology has evolved from driving DVD/CD/Blue-ray optical drives to include laser projection in smartphones, automotive head-up displays (HUDs) and pico projectors. Renesas has developed new LDDs for RGB scanning laser projection systems and laser-based pico projectors. Automotive HUDs are benefiting from big innovations in MEMS projection systems and are now central to advanced driver assistance systems (ADAS) and safety. The latest laser scanned-MEMS projection systems can provide higher resolution images and at a lower cost.
-
Product
16-Ch Isolated Digital Input And 16-Ch Relay USB 3.0 I/O Module
USB-5862
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub16-ch Isolated Digital Input and 16-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
16 Relay Output PCIe Board
APCIE-2200-16
-
16 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16 has 16 relay output channels. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
Text-Based Way to Connect & Disconnect Relays on ABex Modules
ABex Switching
-
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
-
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 12.4 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-780B-511-E
-
The 40-780B-511-E (PXI) and 42-780B-511-E (PXIe) are single failsafe SPDT 12.4 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT front panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
PC Based Test Setup for LED Driver of LED
-
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
Product
PXI Matrix Switch: 4x32, 2-Wire, 100Vrms/2A, Armature Relays
M9120A
-
The M9120A high-density matrix offers higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the durable armature switches allowing multiple channels to be connected at one time, up to 60W per channel. The 4-wire wide bus can be used to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
Product
PCI Express Card With Eight Isolated Inputs, Eight Relay Outputs, And Change Of State Detection
PCIe-IIRO-8
-
This product is a x1 lane PCIe isolated digital input and relay output board with Change of State (COS) detection capabilities.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-780B-541-E
-
The 40-780B-541-E (PXI) and 42-780B-541-E (PXIe) are single failsafe SPDT 40 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Single-in-Line Reed Relays
Series 113
-
SIL relays - Requires a small area of only 0.15 x 0.5 inches (3.8mm x 12.5mm). 10 Watts Form A or 3 Watts Form C switches. Smallest Form C reed relay
-
Product
High Impedance Busbar Differential Relay
MIB
-
The MIB, a member of the M II family of economical and highly functional digital protection relays, is a microprocessor based relay that provides three phase high impedance differential protection for Substation Bus-bars of any voltage level. Use the MIB also to protect electrical machines like transformers, generators or motors against restricted earth faults.
-
Product
Relay I/O Module via Ethernet
2650
-
8 form-C mechanical relays with 240VAC, 2A ratingConnects to an Ethernet through 2601 hub100 mm DIN carrierResponds to interlock and E-stop circuitsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
Pickering Software Drivers & Applications
-
We provide driver packages for LXI and PXI products offering seamless installation and support of all popular Programming languages such as C/C++, LabVIEW™, LabVIEW RT, .NET, VB, LabWindows/CVI, MATLAB®, Python, ATEasy, TestStand™, Veristand™ and Switch Executive™ (via the IVI driver).
-
Product
PCI 32 Channel Reed Relay Output Digital Interface
8007
-
The 8007’s PCI digital I/O interface reed relay outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
Product
Surface Mount Reed Relays
Series 200
-
Surface Mount Reed Relays. Wide range featuring dry or mercury wetted switches. Coaxial version for high speed digital or RF up to 6 GHz. 5, 12 or 24 volt coils with optional diode
-
Product
Safety Relay Modules & Sensors
-
Using safety relay modules, you can reliably implement safety functions in machines and systems. They monitor signals from emergency stop buttons, light grids, and safety door switches, and initiate a safe state where necessary.
-
Product
Relay Test Jumper Kit II
60610
-
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector
42-153-003
-
The 40/42-153-003 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
Waveguide Electromechanical Relay Switches C, X, Ku, K & Ka Bands up to 40 GHz
-
Waveguide Electromechanical Switch models cover C, X, Ku, K, Ka frequency bands up to 40 GHz. SPDT and Optional DPDT* Configurations with Latching Self Cut-Off Actuators, TTL Logic, and Position Indictors with manual override. Patented Motor Drive with Arc Suppression. Designs support WR-137, WR-112, WR-90, WR-75, WR-62, WR-42, and WR-28 waveguide sizes with O Rings for pressurized operation. Power handling capability up to 12 kW CW and 320 kW Peak. These waveguide electromechanical relay switches deliver desirable performance that includes high isolation levels up to 105 dB, and extremely low insertion loss down to 0.01 dB.
-
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
-
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
